Manualios.com

Siemens VersiCharge Installation And Operation Manual

  • VersiCharge Automobile Accessories
  • ma71V1uyttdHs
  • Installation And Operation Manual
  • PDF / Adobe Acrobat Reader
  • 34

Siemens VersiCharge Manual Online:

4.55, 1144 votes
Siemens VersiCharge User Manual
Siemens VersiCharge User Guide
Siemens VersiCharge Online Manual

Text of Siemens VersiCharge User Guide:

  • Siemens VersiCharge, 28 © 813776  When the external contact is closed, the alternate input will control the VersiCharge, preventing it from entering the ‘Charging’ state  The status output is a switch that indicates charging status. When the contacts are closed, the unit is in charging state

  • Siemens VersiCharge, 3 © 813776 Table of Contents 1 Important Safety Information ................................................................................................... 5 1.1 Read this First .................................................................................................................. 5 1.2 Symbol Legend................................................................................................................. 5 1.3 Product Labels.................................................................................................................. 5 1.4 Definitions ..........................

  • Siemens VersiCharge, 8 © 813776 interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio/TV technician for help.

  • 20 © 813776  Locate a stud within the wall to attach the mounting bracket and receptacle. For concrete or masonry walls, install appropriate anchors.  Verify that the stud or anchor and surrounding materials can handle the 20+ lbs load of the VersiCharge.  Verify local code with respect to installation height: o Installation height is regulated by NEC®; however

  • Siemens VersiCharge, 21 © 813776 3.5 Amperage Adjustment The Siemens VersiCharge has the option to set the maximum amperage/power that can be delievered to the car using the Amperage adjustment switch. Note that Versicharge cannot control the power draw to the EV, it can only communicate the current capacity of the device to the EV. Note: The EV controls the power draw. the VersiCharge only communicates the maximum available power to EV. Dial Settings  Amperage adjustment dial is for use by a qualified technician only  Purpose of the amperage adjustmen

  • Siemens VersiCharge, 6 © 813776 Indicates connection point for Ground conductor. 1.4 Definitions The term EV used in this manual refers to an electric vehicle. The term AC used in this manual refers to alternating current. The term Universal unit refers to any VersiCharge with a plug and chord assembly attached, i.e. part numbers VC30XXXU**** (Indoor / Outdoor Use) The term Hardwired unit refers to any VersiCharge which is factory configured for hardwired installation only, i.e. part numbers VC30XXXHW**** (Indoor Use only) The placeholder ‘XXX’ in the mentioned part numbers can either stand for ‘GRY’ which denotes that the unit is g

  • 31 © 813776 product from Siemens, via a non-expedited freight carrier selected by Siemens, to locations within the United States (including Alaska and Hawaii) and Canada, but not to other locations outside the United States or Canada. The Limited Warranty does not cover shipping damage or damage resulting from mishandling by the freight carrier. Any such

  • Siemens VersiCharge, 30 © 813776 Section 6: Warranty Limited Warranty Siemens Industry Inc. ("Siemens") has developed a highly reliable EV Supply Equipment (EVSE), branded as VersiCharge (“VersiCharge EVSE”), that is designed to withstand normal operating conditions when used in compliance with the Siemens Installation and Operations Manual supplied with system as originally shipped by Siemens. The Siemens limited warranty (“Limited Warranty”) covers defects in workmanship and materials o

  • Siemens VersiCharge, 17 © 813776 Rear-fed, Cord-and-Plug Installation Mounting NOTE: Flush mount installations only, meaning the receptacle is even with wall in which it is installed.  Locate a stud within the wall to attach the mounting bracket. o For concrete or masonry walls, install appropriate anchors. o Verify that the stud or anchor and surrounding materials can handle the 20+ lbs load of the VersiCharge.  Ensure that receptacle can be flush mount installed to the left side of the

  • Siemens VersiCharge, 27 © 813776 State Name Description Halo Status Indicator Power Available 240V or 208V Power Present Off Ready to Charge EV detected, waiting for charging command from EV Green - Solid Charging Charging EV Green - Fading in and out Pause Operation paused Off Delay Timer Operation awaiting delay timer Off Remote System is controlled via remote control interface Off Halo Deactvation The Halo indicator on the versiCharge can be deactivated to marginally lower power consumption of your device dur

  • Siemens VersiCharge, 5 © 813776 1 Important Safety Information 1.1 Read this First This manual contains important instructions for use during installation and maintenance of the Siemens VersiCharge™ electric vehicle charging station. 1.2 Symbol Legend To reduce the risk of electrical shock, and to ensure the safe installation and operation of the Siemens VersiCharge™, the following safety symbols appear throughout this document to indicate dangerous conditions and important safety instructions. DA

  • Siemens VersiCharge, 26 © 813776  While in use, the cord can be unwrapped, loop by loop, to allow sufficient length of cord to be unwound to reach the EV receiver WARNING! Failure to properly protect the connector and the cord could result in damaged components, which could prevent the VersiCharge from functioning properly or create a hazardous situation. 4.5 Delay Timer The VersiCharge has a built in delay timer to allow users to select the time that they would like for their EV to charge. The delay timer will prev

  • Siemens VersiCharge, 13 © 813776 2.6 Device States EVSE's do not have the capability to determine whether your car has been charged or not, refer to car manual for indication of car battery status. State Name Description Indicator(s) Halo Status Indicator Power Available 240V or 208V Power Present 'Power Available' Off Ready to Charge EV detected, waiting for charging command from EV 'Power Available' and "Ready Green - Solid Charging Charging EV 'Power Available' and 'Charging' Green - Fading in and out Pause* Operation paused 'Power Available" and

  • Siemens VersiCharge, 15 © 813776  The VersiCharge will mount on the surface of the wall, protruding at least 15 inches, and a location for installation should be chosen where there is sufficient space to park an EV, walk past the device, open nearby doors, etc., without obstruction.  If the installation location is not already wired for installation, installation of the VersiCharge unit should be planned with an electrician and then the electrician should bring in the electricity according to those guidelines. DANGER Explosion hazard. This equipment has arcing or sparking parts that should not be exposed

  • 25 © 813776 The VersiCharge will automatically disconnect power in the event of a fault.  If a fault occurs during charging, the VersiCharge will disconnect power from the EV, with an audible click, and change to the ‘Fault’ state. The VersiCharge will automatically self-recover when all faults clear, with the exception of grounding faults.  For grounding faults,

  • Siemens VersiCharge, 9 © 813776 2: Device Layout 2.1 Exterior – Front 1. Pause Button 2. Delay Timer Button 3. Connector 4. Connector Holster 5. Halo Indicator 6. Closure Screws 7. Hinges 2.2 Exterior – LED Indicators 1. Pause 2. Charging 3. Power Available 4. Ready 5. Fault 6. Remote Control Activated 7. Service Portal 8. Time Delay 9. Hour Delay 10. Remote Control Lock Note: Wi-fi and zigbee communication are not enabled for these versions. 2 1 3

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Philips 379161116 Brochure philips/379161116-7J5.pdf 15 Nov 2022 3 1.56 Mb
2 Kleenmaid KED597-4350 Use and care manual kleenmaid/ked597-4350-75B.pdf 22 Aug 2022 19
3 Insignia NS-PNC5001 Quick setup manual insignia/ns-pnc5001-OB2.pdf 03 Oct 2022 2
4 Philips US2-P44418A Operation & user’s manual philips/us2-p44418a-W23.pdf 04 Jul 2023 16 0.35 Mb
5 KitchenAid KEBS177SWH - 27 Inch Single Electric Wall Oven Installation instructions manual kitchenaid/kebs177swh-27-inch-single-electric-wall-oven-VA9.pdf 21 Jun 2022 6
6 Bush BFSAT01SD Quick start bush/bfsat01sd-C73.pdf 20 Mar 2023 2 0.95 Mb

Similar Resources:

  • Ecco

    EW4008

    (9 pages)
    Page 1 of 3Specications:Overall dimensions: 9.81” x 3.36” x 3”Weight: 2.70 lbs. / 1.23 kgInput Voltage: 12-24VDCTemp. Range: -40° to 65°C -40° to 150°FPower Consumption for low beams (per light): 20W Max Power Consumption for high beams (per light): 36W MaxPower Consumption for indicator light (p …
  • Thule

    COMPLETE RAILING CARRIER 45050

    (4 pages)
    45050/45058 COMPLETE RAILING CARRIERPARTS INCLUDED • PIÈCES INCLUSES • PIEZAS INCLUIDASAB CDE F Grailing foot / pied de rail / pie de la barra lateralhandle assembly / poignée / ensamblaje del asaendcap / capuchon / tapa de extremoload bar (45050) / barre (45050) / la barra (45050)load bar (45058) / barre (45058) / la barra (45058)change key / clé d� …
  • Yakima

    Locking RailRider 3

    (6 pages)
    Locking RailRider 3Tighten bases.Do not over-tighten the bases — the towers mayhave difficulty sliding on.Once you have determinedyour crossbar spread,measure for equal distances onboth sides of thevehicle.Open levers to loosentower screws.PRIOR TOINSTALLATION:USTO REMOVE FACTORY-INSTALLED RACKS:• Open rear hatch door.• Pry up the track cover-plate.INS …
  • Intermec

    CV60

    (2 pages)
    Worldwide Headquarters6001 36th Avenue WestEverett, Washington 98203U.S.A.tel 425.348.2600fax 425.355.9551www.intermec.com© 2007 Intermec TechnologiesCorporation. All rights reserved.CV60 Vehicle Mount Computer Quick Start Guide*930-162-003*P/N 930-162-003CV60Where to Find More Information󲀃󱓢󱅪󰭂󱐊󰒚󲵆󰘞󱻲󲵆󱷚󱶢󰴂󱶾 …
  • JL Audio

    Stealthbox SB-J-JTGLAD/10TW1

    (5 pages)
    INSTALLATION GUIDE for the SB-J-JTGLAD/10TW1 SKU# 946812020 & Up Jeep Gladiator (JT)Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.We strongly recommend that you have your new Stealthbox® installed by …
  • Lippert Components

    Ground Control 2.0

    (2 pages)
    Rev: 09.11.2018 Page 1 CCD-0002105AUTO-ELECTRIC LEVELING SYSTEM STABILIZER INSTRUCTIONSQR-063LEVELING AND STABILIZATIONDropping Off TrailerNOTE: Prior to unhitching from the tow vehicle, ensure the fifth wheel is parked on a level surface and chock the tires of the fifth wheel.1. Disconnect any wires, chains or sway control that may be equipped between the …

Comments, Questions and Opinions: