Manualios.com

Siemens SIMATIC TI505 Installation And Operation Manual

  • SIMATIC TI505 Adapter
  • ma71V1uyttdHs
  • Installation And Operation Manual
  • PDF / Adobe Acrobat Reader
  • 66

Siemens SIMATIC TI505 Manual Online:

4.1, 2535 votes
Siemens SIMATIC TI505 User Manual
Siemens SIMATIC TI505 User Guide
Siemens SIMATIC TI505 Online Manual

Text of Siemens SIMATIC TI505 User Guide:

  • Siemens SIMATIC TI505, Index-3 T Technical assistance, x TIWAY I network connecting S5 PLCs, 1-4 local area network, 1-4 Network Interface Modules, 1-4 parameters, 2-7 port, 2-6 protocol, 3-8 U UniLink models, x, 3-2 V Voltage supply, x, 3-2

  •                  

  • Siemens SIMATIC TI505, TIWAY I Network Communication 3-11 S5 UniLink Adapter Installation and Operation 3.7 Receiving with the 3964R Procedure After a successful transmission of the data information has been made to the partner, the procedure enters the idle state awaiting the link to be established by the partner. If the procedure receives any character (except STX) while in the idle state, it waits until the character delay time (220 ms) has elapsed and then sends a NAK character. Then a repetition is expected. If after a total of six unsuccessful attempts, or if the repetition by the partner does not take place within the waiting time of 4 seconds, the procedure breaks off reception

  • Siemens SIMATIC TI505, BUSINESS REPLY MAIL FIRST CLASS PERMIT NO.3 JOHNSON CITY, TN FOLD FOLD POSTAGE WILL BE PAID BY ADDRESSEE NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES SIEMENS INDUSTRIAL AUTOMATION, INC. 3000 BILL GARLAND RD. P.O. BOX 1255 JOHNSON CITY TN 37605–1255 ATTN: Technical Communications M/S 3519

  • Siemens SIMATIC TI505, TIWAY I Network Communication 3-3 S5 UniLink Adapter Installation and Operation The pin assignments for these ports are listed in Table 3-2. Table 3-2 Local Line Connector Pin Assignments Pin Name Description 1 2 3 4 5 6 7 8 9 Shield LLM+ LLM– Reserved Reserved Cable shield and signal common Reserved Reserved Positive biased signal line Reserved Reserved Negative biased signal line The Local Line interface uses shielded, twisted-pair cable, such as Belden  9860 or Belden 9271. Figure 3-2 shows the TIWAY I bus structure with the network trunkline cable, which can extend up to 25,000 feet with droplines up to 100 feet in length. I003647 SIMATIC S5 PLC CP 525 RS-232 S5 Interfac

  • Siemens SIMATIC TI505, Installation and Set-up 2-2 S5 UniLink Adapter Installation and Operation 2.1 Overview This chapter provides an introduction to the operation and set-up of the S5 UniLink Adapter. During normal operation, requests are sent over the TIWAY network to the S5 UniLink Adapter; thus it functions in the same manner as any other secondary in the network. Appendix B lists the TIWAY primitives supported by the S5 Adapter. The majority of requests issued to the S5 Adapter are to obtain memory locations from the S5 PLC.

  • Siemens SIMATIC TI505, TIWAY I Network Communication 3-1 S5 UniLink Adapter Installation and Operation Chapter 3 TIWAY I Network Communication 3.1 Local Line Interface Ports 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local Line Interface Ports 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local Li

  • Siemens SIMATIC TI505, Installation and Set-up 2-3 S5 UniLink Adapter Installation and Operation For the S5 UniLink Adapter to establish communications with the CP 525 module, the following prerequisites must be met. Use the PG programmer to load these parameters. • The STEP 5 user program in the CPU must include the data handling blocks SEND ALL and RECEIVE ALL. • The CP 525 user program of the CP module must include the RK 512 Interpreter and the 3964R Transfer Procedure. NOTE: Remember to program the communications par

  • S5 Adapter/CP 525 Error Codes C-2 S5 UniLink Adapter Installation and Operation C.1 S5 UniLink Adapter Primitive Exceptions During operation, two possible error codes could be returned by the S5 UniLink Adapter: primitive exceptions, and CP 525 errors. The error byte of a primitive exception contains one of the following. Request: None Response: LLLL 00 PP DDDD Table C-1 Primitive Except

  • Siemens SIMATIC TI505, Simatic S5 Memory Mapping A-11 S5 UniLink Adapter Installation and Operation A.10 S5 Data Types Not Supported by S5 PIM Due to significant differences in the internal memory structure and architecture between the TI500/TI505 PLCs and the S5 PLCs, no compatible memory translations to these specific S5 data types are available. The S5 Analog I/O Bytes memory type as accessed through a CP module is not supported by the S5 PIM. Access to Analog I/O will be through Data Block memory, which implies that all analog conversions will be taken care of in the STEP 5 program. This was determined bec

  • Siemens SIMATIC TI505, viii Contents List of Tables 1 S5 UniLink Adapter Models x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 S5 UniLink Adapter Models 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Local Line Connector Pin Assignments 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 RS-232/RS-423 D Connector Pin Assignments 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Siemens SIMATIC TI505, Installation and Set-up 2-6 S5 UniLink Adapter Installation and Operation 2.3 Setting the Dipswitches Two banks of dipswitches are provided on the S5 UniLink CPU board, accessible by opening the cover plate on the face of the unit (see Figure 2-4). A000653a S5 PIM Dipswitch 1 Dipswitch 2 I003643 Figure 2-4 S5 UniLink Adapter Dipswitch Location Dipswitch 1 is used to configure the S5 Interface Port and the TIWAY network port, as shown in Figure 2-5. The data rate of the S5 UniLink Adapter interface port can be set for either 9600 or 19,200 baud using switch 3 on Dipswitch 1 (see Figure 2-5). The remaining comm

  • Siemens SIMATIC TI505, Simatic S5 Memory Mapping A-6 S5 UniLink Adapter Installation and Operation A.5 Input Bytes — CP 525 ‘E’ Type The S5 Input Bytes memory, as accessed through a CP module, refers to memory that is organized in 128 contiguous bytes of memory. Because the process input image memory area (E memory) is accessible only if a corresponding I/O module is in use, the S5 PIM assumes no knowledge of the accessible memory area of the process input image. The TT types that map to this type of S5 memory are Packed Input Discretes (TT Type 06) and Unpacked Input Discretes (TT Type 03). NOTE: If a TIWAY request is out of range, the excepti

  •                      

  • Siemens SIMATIC TI505, TIWAY I Network Communication 3-2 S5 UniLink Adapter Installation and Operation 3.1 Local Line Interface Ports The S5 UniLink Adapter is available in four models, offering a choice of two physical interfaces for network communications: Local Line or RS-232-C interfaces, in different voltage versions. Table 3-1 lists the model numbers, the type of interface, and the supply voltage for each model. Table 3-1 S5 UniLink Adapter Models Model Number Network Port Supply Voltage PTI:505–7115 Dual Local Line 120 VAC PTI:505–7116 Dual RS-232C/423 120 VAC PTI:505–7117 Dual Local Line 240 VAC PTI:505–7118 Dual RS-232C/42

  • Siemens SIMATIC TI505, iv Contents 3.2 Modem Interface Ports 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232-C Modem Interface Ports 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modem Port Pin Assignments 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modem Specifications 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Siemens SIMATIC TI505, Simatic S5 Memory Mapping A-10 S5 UniLink Adapter Installation and Operation A.9 Counter — CP 525 ‘Z’ Type The S5 Counter memory, as accessed through a CP module, refers to memory that is organized by 256 contiguous words of memory. Because the accessible Counter memory is different for different CPUs, the S5 PIM assumes no knowledge of the accessible memory ranges for Counter memory. The TT type that maps to this type of S5 memory is Counter Current (TT Type 16). The Timer/Counter Current TT Type 0F accesses S5 Timer memory only, thus no access to S5

  • Siemens SIMATIC TI505, MANUAL PUBLICATION HISTORY SIMATIC TI505 – S5 UniLink Adapter Installation and Operation Order Manual Number: PPX:505–8116–2 Refer to this history in all correspondence and/or discussion about this manual. Event Date Description Original Issue 09/92 Original Issue (2800120–0001) Second Issue 04/94 Second Issue (2800120–0002)

  • Siemens SIMATIC TI505, Simatic S5 Memory Mapping A-9 S5 UniLink Adapter Installation and Operation A.8 Timer — CP 525 ‘T’ Type The S5 Timer memory, as accessed through a CP module, refers to memory that is organized by 256 contiguous words of memory. Because the accessible timer memory is different for different CPUs, the S5 PIM assumes no knowledge of the accessible memory ranges for timer memory. The TT types that map to this type of S5 memory are Timer Current (TT Type 14) and Timer/Counter Current (TT Type 0F). The Timer/Counter Current TT Type 0F will access S5 Timer memory only, thus no access to S5 Counter memory will be provided through TT T

  • Siemens SIMATIC TI505, Contents v A.5 Input Bytes — CP 525 ‘E’ Type A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Address Mapping A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Value Conversion A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Siemens SIMATIC TI505, TIWAY I Network Communication 3-7 S5 UniLink Adapter Installation and Operation 3.3 Redundant Media Transmission Most TIWAY I conformant devices support a redundant media scheme which provides active access to a device over one of two independent media channels. Port 2 on both Local Line and RS-232 models of the S5 UniLink Adapter provides support for redundant media transmission. If access to a device fails on one channel, communications can be automatically or manually switched to the alternate channel. This type of a circuit is illustrated in Figure 3-5.

  • Siemens SIMATIC TI505, Copyright 1994 by Siemens Industrial Automation, Inc. All Rights Reserved — Printed in USA Reproduction, transmission or use of this document or contents is not permitted without express consent of Siemens Industrial Automation, Inc. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Since Siemens Industrial Automation, Inc. does not possess full access to data concerning all of the uses and applications of customer’s products, we do no

  • Siemens SIMATIC TI505, TIWAY I Primitives Supported by S5 PIM B-5 S5 UniLink Adapter Installation and Operation Primitive 04 is the format primitive that allows you to determine the maximum length of the primitive acceptable to the Network Interface Module. The buffer length is returned in number of bytes. Request: LLLL 04 Response: LLLL 04 NNNN MM EE FF GG BB ... BB Symbol Value Definition NNNN 010E Primitive field length supported. MM 20 Number of Data Acquisition Blocks supported. EE 00 Number of Data Acquisition Records supported. FF 00 Number of Da

  • Product Overview 1-1 S5 UniLink Adapter Installation and Operation Chapter 1 Product Overview 1.1 Description of the S5 UniLink Adapter 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting a SIMATIC S5 Controller to a TIWAY Network 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . S5 UniLink Adapter Components 1-2. . . . . . .

  • S5 Adapter/CP 525 Error Codes C-3 S5 UniLink Adapter Installation and Operation C.2 CP 525 Error Codes If the CP 525 module responds with an error code, it is returned in the following 80DD word. The DD field will contain the CP 525 error code byte. In order to determine the meaning of this error code, you must refer the value DD to the appropriate CP 525 manual

  • Siemens SIMATIC TI505, Simatic S5 Memory Mapping A-8 S5 UniLink Adapter Installation and Operation A.7 Flag Bytes — CP 525 ‘M’ Type The S5 Flag Bytes memory, as accessed through a CP module, refers to memory that is organized by 255 contiguous bytes of memory. The TT types that map to this type of S5 memory are Packed Control Register (TT Type 08) and Unpacked Control Register (TT Type 05). S5 Flag Bytes Memory TI500/TI505 Control Register Memory Address Address = CCCC (hex) 32107654 Byte Address: Quotient of (CCCC / 8) Bit Address: Remainder of (CCCC / 8) When converting the value for Packed Control Registers, the most significant bit (MSB) of the

  • Siemens SIMATIC TI505, Installation and Set-up 2-5 S5 UniLink Adapter Installation and Operation The pin assignments for the S5 interface are shown in Figure 2-3. Any pins not listed in the diagram should remain unused in order to prevent damage to the communications processor or the S5 UniLink Adapter. NOTE: Do not exceed 50 feet in length for the communications cable. 1 2 3 4 5 6 20 8 7 1 2 3 4 5 6 20 8 7 (DTE) (DTE) GND 99 10 10 11 11 12 12 13 13 CP 525 Communications Processor S5 UniLink Adapter 14 14 TD TD RD RD RTS RTS CTS CTS GND DSR DCD DSR DCD 25 25 DTR DTR I003642 Figure 2-3 Pin Assignments for Connecting S5 Adapter to CP 525 S5 Interface P

Related Products and Documents (Adapter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Johnson Screens PVC Manual  johnson-screens/pvc-71T.pdf 10 Dec 2022 2
2 Marshall Electronics VS-547-3GSDI Operation & user’s manual marshall-electronics/vs-547-3gsdi-155.pdf 08 Feb 2023 74
3 West Bend L4972T Manual  west-bend/l4972t-485.pdf 26 Sep 2022 27
4 HP EliteBook 830 G6 Product end-of-life disassembly instructions hp/elitebook-830-g6-OCT.pdf 24 Dec 2023 32
5 Frigidaire GLGR331MA Factory parts catalog frigidaire/glgr331ma-7H8.pdf 17 Oct 2023 12 0.77 Mb
6 GE ZV42 Owner's manual ge/zv42-IZ6.pdf 22 Nov 2022 12

Similar Resources:

  • Baby Jogger

    citymini

    (1 pages)
    1 2 3NOTE: When seat is not in reclined position, the rear flaps of the rain canopy can be snapped together for a tighter fit.NOTE: The zippered opening on the front of your Rain Canopy provides quick and easy access to your child.4 5NOTE: It is not necessary to lay your stroller handle on the ground or remove the wheels to attach the rain canopy to your str …
  • Hioki

    Z3230

    (2 pages)
    無線 LANアダプタWIRELESS LAN ADAPTER取扱説明書 / Instruction ManualDec. 2021 Revised edition 4Z3230A960-04 21-12HZ3230JA/ENはじめにHIOKI Z3230 󵇼󶦸LAN󸸀󲰫󸎉Z3230 LR8450-01 󵥌󵇼󶦸󱸇󱗡 …
  • Sun Microsystems

    x4422a

    (96 pages)
    Sun Microsystems, Inc.www.sun.comSubmit comments about this document at: http://www.sun.com/hwdocs/feedbackSun™Dual Gigabit Ethernet andDual SCSI/P Adapter Installationand User’s GuidePart No. 817-4339-10January 2004, Revision A …
  • Wiseup

    WIFI23

    (161 pages)
    WIFI23 User Guide I. Product Overview 1. Camera Lens 2. Indicator Light 3. Reset Button 4. Micro SD Card Slot II. What’s In the Box -Mini CD Disc -Card Reader -WIFI AC Adapter Camera III. Network Setup 3.1. Install the P2PLiveCam APP Search for the P2PLiveCam APP in Google Play Store or Apple Store and install it on your smartphone or t …
  • HP

    NC380T

    (8 pages)
    The HP NC380T server adapter is the industry's first PCI Express dual port multifunction network adapter supporting TOE (TCP/IPOffload Engine) for Windows, and iSCSI (Internet Small Computer System Interface) over a single network connection. Each port onthe NC380T is a four lane (x4) serial device designed for PCI Express slots. The NC380T comes with a …
  • Hama

    Nano Bluetooth USB Adapter

    (34 pages)
    00049234/12.09 All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.Hama GmbH & Co KGD-86651 Monheim/Germanywww.hama.com …

Comments, Questions and Opinions: