Shinko HR-700 Instruction Manual
|
Shinko HR-700, 95 10.1.3 When there is a Major Error 10.1.4 When the Trend Recording is deflected Flowchart 2 Major erro r Scaling setting proper? Calibration correct? Calibrate again. (See 9.5 on Page 91) Set it properly. (See 7.1.1 on Page 46) Zero/span position of chart pape r p ro p er? NO YES YES YES YES NO NO NO Calibrate again. (See 7.2.11 on Page 78) (Dot printing error) Contact our dealer where you purchased the instrument, or our sales representative. Display or printed value matches dot p rintin g value? Flowchart 3 Trend Recording is Deflect
Shinko HR-700, 45 「」 [Note] In the , , or mode, press the “ENT” key to select the range. Use the key to select a range type. “ENT” key 10mV 0 to 20mV 0 to 50mV 200mV 1V 0 to 5V 10V 4 to 20mA Range Mode B R S K E J T C Au-Fe N PR40-20 PL- U L Pt100 JPt100
61 7.1.7 Setting other functions Other functions can be set as the following. Setting Items (1) (Printing cycle) Selects a printing cycle from 10, 20, 30, and 60 seconds. (2) (Zone recording) The data for each channel can be recorded separately in another area so as not to be overlapped. (3) (Partial compression/expansion) Records the measured data of the channel,
Shinko HR-700, 83 (3) Error Detection If the recorder receives data as a result of a signal error such as parity error and framing error due to noise or hardware problems, this data will be ignored. Consequently, a data format error will result, as the data was not sent in the normal data format. That command will not be executed in the receiving function, and no response will be resulted in the transmitting function. The data format error status can be confirmed by the ESC S command (described later).
Shinko HR-700, 110 11.3 Standard Setting Functions 11.3.1 Standard Setting Functions Table 11.3.1 Standard Setting Functions Function Description Burnout To deflect over toward 100% with disconnecting input. Every channel’s burnout can be specified. (DC voltage of 50mV max., TC input ) Tag Number Sets a tag number by up to 7 figures per channel. (Prints at a logging print) Reference Junction Compensation Specifies an inside/outside of the Reference Junction Compensation. Copy Function Copies a channel setting. Input o
Shinko HR-700, 31 6. RUNNING 6.1 Running Once the power is turned on, the display on the front of the door lights. The instrument will be ready to run (user mode) in about 5 seconds, including the initial screen. If the REC lamp is unlit, press the “REC” key to start recording operation. 6.1.1 Status after Initial Screen (1) Display screen : The “REC” lamp keeps the status of before power-off. (2) Printout data : All printing data and analog recording data of before power-off are cleared. (3) Alarm and Diagnosis : Alarm indications and output information are not rcover
Shinko HR-700, 35 (2) Manual print stopping procedure 1) Press the “PRINT” key. 2) Use the “PRINT” key to display “ ” , and press the “ENT” key. 3) Use the “PRINT” key to select “ ” . Pressing the “ENT” key stops manual print. However, printing will continue until the line is completely printed. Then manual print will stop, and the display will return to the status prior to starting manual print. Fig. 6.4.1 Manual Print 6.4.2 List Print Prints the following se
Shinko HR-700, 62 (1) (Printing Cycle) Example) Setting the printing cycle to 60 seconds. Press the “MENU” key for 3 seconds or longer to enter the setup mode. Use the key to display " ", and press the “ENT” key. Use the key to display " ", and press the “ENT” key. Use the key to select the printing cycle " ", and press the “ENT” key. Press the “ENT” key. Setting is completed. To return to the user mode, press the “MENU” key for 3 seconds or longer. (2)
Shinko HR-700, 74 (3) Alarm print ON/OFF Sets the alarm print ON/OFF. When ON1, prints the alarm occurring and the alarm recovering. When ON2, prints only the alarm occurring. Example) When setting both the alarm occurring and the alarm recovering. Enter the engineering mode (See the key operation on page 67). Use the key to display “ ”, and press the “ENT” key. Use the key to select “ ”, and press the “ENT” key. Use the key to display “ ”, and press the “ENT” key. Once setting is completed, the recorder will return to the Alarm Print Setting screen. (4) Logging print ON/
Shinko HR-700, 57 (1) Character code table 2 3 4 5 6 7 A B C D E F 0 SP 0 @ P p 0 0 Π π 1 ! 1 A Q a q 1 1 A P α ρ 2 " 2 B R b r 2 2 B Σ β σ 3 # 3 C S c s 3 3 Γ T γ τ 4 $ 4 D T d t 4 4 Y δ υ 5 % 5 E U e u 5 5 E Φ ε φ 6 & 6 F V f v 6 6 Z X ζ χ 7 ' 7 G W g w 7 7 H Ψ η ψ 8 ( 8 H X h x 8 8 Θ θ ω 9 ) 9 I Y i y 9 9 I ι A : J Z j z K κ B + ; K [ k { + + Λ λ C , < L l | M μ D – = M ] m } N ν E . > N ^ n  ̄ - - Ξ ξ F /
Shinko HR-700, 27 (9) Turn the Sprocket Drum Gear Check paper feed using your hand. Turn the sprocket drum gear to feed out the chart paper. (4 sections of chart paper should be fed out.) Fig. 5.1-9 Checking Paper Feed (10) Put the Chart Paper Holder back Insert the chart holder horizontally into the case until it is locked. Fig. 5.1-10 Putting Back the Chart Holder Turn the gear at the left end of the sprocket drum in the arrow direction. Chart Receiver Chart guide When inserting it, push the paper receiver.
Shinko HR-700, 25 (5) Loosen the chart paper The chart paper may not be properly fed, if stuck. Be sure to loosen the paper. Fig. 5.1-5 Loosening the Chart Paper (6) Set the Chart Paper into the Storage Chamber Unfold 2 sections of chart paper. Holding the printing surface upward, set it in the storage chamber. Fig. 5.1-6 Setting the Chart Paper Square Holes on the Left Sprocket Drum Storage Chamber Rectangular Holes on the Right
Shinko HR-700, 107 For input 4 to 20mA, the square root computation accuracy is as the following formula. Measuring 100% 100 = = = 0.16% rdg Measuring 50% 50 = = = 0.19% rdg Measuring 9% 9 = = = 2.3% rdg Measuring 1% 1 = = 5(0.002 +12.5) = 62.5% rdg If the process variable is low, as above, its accuracy rating is not valid. (3) Decade The accuracy rating at the decade computation is defined as the logarithm of display value. Under normal opera
98 10.2 Self Diagnosis Function (ERROR) This instrument always diagnoses itself on the items listed in the Table 10.2.1 below. When an error is found after self diagnosis, a relevant error number is displayed. 10.2.1 Self diagnosis Items Table 10.2.1 List of Diagnosis Items Type Error message Part Diagnosis Remedy Zero point sen
Shinko HR-700, 55 Setting hereinafter is valid only for the model to which an alarm output (option: LH6) has been added. If the option has not been added, press the “ENT” key until " " is displayed. Then, press the “ENT” key again. Setting is completed. When an alarm occurs, the alarm output is issued from the alarm output relay. Use the key to select alarm output ON and press the “ENT” key. If the alarm output is not used, select OFF and press the “ENT” key. If the alarm output is set to ON, set the relay number. Use the key to select a relay number out of 1 to 6, and press the “ENT” key. Press the “ENT” key
Shinko HR-700, 88 8.5 Outputting the Status If the open-link recorder has a data error on its link, it will save the error as a communication error in the internal status area. The (ESC S) command reads this status. Issuing the command clears the on-going error. 8.5.1 Status Output Command ESC S(CR) (LF) Upon receiving this command, outputs will be the status of commands received so far. 8.5.2 Status Output XX: 00 to 19 Table 8.5.2 Status output list Status factor Status factor Status output A/D END Syntax er
Shinko HR-700, 49 About Square Root Computation The square root computation is as follows: Each item is defined as follows: SPAN L : Span lower-limit value (Span L) SPAN R : Span upper-limit value (Span R) SCAL L : Scaling lower-limit value (Scale L) SCAL R : Scaling upper-limit value (Scale R) IN : Input voltage OUT : Output (Scaling value) When an input value is 1% or more (1 to 100%) OUT = (SCAL R – SCAL L ) x + SCAL L When an input value is less than 1% OUT = x (IN – SPAN L ) + SCAL L Example) When setting on the previous page is performed, the display is shown as below. Input voltage (
11 2.2.2 Operation Keys The following describes functions of each operation key. The actual operation keys are described as shown below. Fig. 2.2.2 Operation Keys in this manual Table 2.2.2 Names of Operation Keys and Their Functions Key Name Function “REC” key Starts/stops recording. To stop, press the “REC” key for
Shinko HR-700, 37 6.4.3 Engineering List Print Engineering list print provides the following setting data of the instrument on the chart paper. Analog recording Digital printing Burnout/RJC, etc. (1) Engineering list print operating procedure 1) Press the “MENU” key. 2) Use the “PRINT” key to display “ ”, and press the “ENT” key. 3) Use the “PRINT” key to select “ ”. Pressing the “ENT” key executes engineering list print. Once engineering list print starts, the display automatically returns to the Data Display screen. Up
23 5. PREPARATIONS FOR OPERATION 5.1 Setting the Chart Paper (1) Press the “REC” key for 3 seconds or longer Stop recording operation. With the power turned on, press the “REC” key for 3 seconds or longer. Fig. 5.1-1 Pressing the “REC” key (2) Open the Door Push the door hook to unlock the door. Pull out
Shinko HR-700, 66 (6) (Comment Words) Example) Setting "ON" for Comment 1( ). Press the “MENU” key for 3 seconds or longer to enter the setup mode. Use the key to display " ", and press the “ENT” key. Use the key to display " ", and press the “ENT” key. Use the key to select a comment number. Display " " and press the “ENT” key. Set " " as the 1st character. Use the key to select a code, and use the key to shift a digit. Press the “ENT” key. Set " " as the 2nd character. Operate in the same manner as
Shinko HR-700, 108 11.2.3 Individual Specifications Table 11.2.3 Specification Items Block Item Specification Measuring Point 6 Input Sampling 10s/6CH Input Display Interval 2.5s Recording Form Printing Form Wire dot (6-color ink ribbon) Recording Width 100mm Print Period 10s/6CH [Note 1] Chart paper Length: 16m, Width: 114mm, Folding width: 40mm The length of the Clean Chart is 12m. Chart feed speed 0, 1, 2, 3, 4, 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 80, 90, 100, 120, 150, 160, 180, 200, 240, 300, 360, 375, 450, 600, 720, 750, 900, 1200, 1500mm/h (Analog recording wil
44 (2) (Current/Voltage), (Thermocouple), (Resistance Temperature Detector) [Note]: When changing a decimal point position, change it during (3) Scaling (pages 46, 47) Measures Current, Voltage, Thermocouple and RTD. Example) When setting Thermocouple T for Channel 1 (T: -100 to 300 ) Press the “MENU” key for 3 seconds or longer to enter the setup mode. Displays
Shinko HR-700, 111 No.HR71E5 2004.11 SHINKO TECHNOS CO.,LTD. OVERSEAS DIVISION : : : : Reg. Office Mail Address URL E-mail 2-48, 1-Chome, Ina, Minoo, Osaka, Japan P.O.Box 17, Minoo, Osaka, Japan http://www.shinko-technos.co.jp [email protected] Tel : Fax: 81-72-721-2781 81-72-724-1760
92 (1) Calibration of Voltage Conduct calibration in the case of voltage, current or thermocouple input. For thermocouple input, calibrate reference junction compensation together. Calibrate the voltage according to the instructions in Section “7.2.12 Data Calibration” (Calibration of the voltage).(See page 79) (2) Calibration of RTD (Resi
Shinko HR-700, 106 11.2.2 The Accuracy at the Computation (1) Scaling The accuracy rating at the scaling is shown as the following formula. Scaling accuracy (digits) = (Range accuracy rating (digits) x Scaling factor + 2 digits) But, Scaling factor = Example 1) When VOLT range is –1.000 to 1.000V and Scaling range is 0.00 to 100.00. Range accuracy rating = 0.1% x 1.000V + 3 digits (Input +1.000V) = 4 digits Scaling factor = = 5 Therefore, Scaling accuracy = (4 x 5 + 2) = 22 digits Analog recording accuracy = 4+{1000– (–1000)} x = 10 digits
Shinko HR-700, 28 (11) Close the Door Close the door and check a door lock. (12) Press the “FEED” key to check Paper Feed Press the “FEED” key on the display keyboard to feed the chart paper. Fig. 5.1-11 Pressing the “FEED” key (13) Press the “REC” Key to restart Operation The chart paper is fed while pressing the key. Releasing the key stops paper feed. The paper begins a slow feed when the key is pressed. Prior to the operation of the instrument, be sure to confirm that the chart paper is being fed!! L M
Shinko HR-700 Voice Recorder Command manual
HR-700 |
Shinko CIT-200 Voice Recorder Instruction manual
CIT-200 |
Samsung SV7000W Voice Recorder Service manual
SV7000W |
Voice Magic VR-2008 Voice Recorder Operation manual
VR-2008 |
Panasonic WJ-NV300K Voice Recorder Quick reference manual
WJ-NV300K |
Cisco Nexus 7000 Series Voice Recorder Command reference manual
Nexus 7000 Series |
Lexicon PCM 80 Voice Recorder Operation & user’s manual
PCM 80 |
Sennheiser 503125 Voice Recorder Instruction manual
503125 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Akura | APL2YR2068U | Instruction book | akura/apl2yr2068u-VZ4.pdf | 18 Nov 2023 | 26 | 2.79 Mb |
2 | Homelite | UT80516 | Operator's manual | homelite/ut80516-OJI.pdf | 11 Mar 2023 | 56 | 9.18 Mb |
3 | GE | GFWH2400L | Dimensions and installation information | ge/gfwh2400l-7S1.pdf | 10 Sep 2022 | 3 | 0.95 Mb |
4 | Triarch | Indoor Lighting 60142 | Assembling instructions | triarch/indoor-lighting-60142-47Z.pdf | 22 Jan 2023 | 1 | 0.16 Mb |
5 | MTD | 129-271R000 | Owner's manual | mtd/129-271r000-3HS.pdf | 11 Feb 2023 | 20 | |
6 | GE | WWA8344V | Use and care manual | ge/wwa8344v-72R.pdf | 19 Sep 2022 | 28 | 5.11 Mb |
Marantz
1SETTING UPINTRODUCTIONThank you for your purchase of the MarantzProfessional PMD680 PC Card Recorder. The PMD680 isthe next generation of portable digital recorders thatbridge the gap between real-time audio recording andcomputers — while keeping the size and functionality ofour renowned portable cassette and MiniDisc recorders.The PMD680 has been design …
PMD680(29 pages) |
Olympus
CÂMARA DIGITALSTYLUS-7020/µ-7020STYLUS-7010/µ-7010● ObrigadoporteradquiridoumacâmaradigitalOlympus.Antesdeutilizarasuanovacâmara,leiaatentamenteestemanualdemodoausufruirdeumexcelentedesempenhodasuacâmaraedeumaduraçãoprolongada.Mantenhaeste …
S701 - Pearlcorder Microcassette Dictaphone(72 pages) |
Safa Media
Missi2000 building 101, 725, Suseo-Dong, Gangnam-Gu, Seoul, KoreaTEL: 02-3413-2020(Rep)FAX: 02-3413-2029E-Mail:[email protected]'s ManualIC RECORDERIRS-810L / IRS-1610LThank you for your purchasing a Sound MAP.Please read this User Guide before you use your Sound MAP.SF69-00139ASAFA MEDIA Co., Ltd.
…
IRS-810L(12 pages) |
Sylvania
SUPPLEMENTSERVICE MANUALDVD RECORDER & VIDEO CASSETTE RECORDERDVR90VEDUBBINGCHANNELVCRRECORDOPEN/CLOSEPLAYREWPOW ER F.F WD STOP/EJECTOUTPUT SELECTVCR DVDSTOP PLAYDVDRECORDS-VIDEO VIDEO L - AUDIO - RThis service manual supplement is for the DVR90VE W1.5 Version model, which are different from previous DVR90VE model. For DVR90VE W1.5 Version model, FUNAI m …
DVR90VE(14 pages) |
Zoom
Operating the Zoom H1 Handy Recorder for Message Banking Contents Page 1. Turning the Zoom H1 on and off ………………………… 2. Recording a Message ……..……………………………… 3. Playing a Recorded Message …………...….................. 4. Moving to the Previous/Next Recorded Message …… 5. Adjusting the Play Vo …
Handy REcorder H1(5 pages) |
Plum
1 PROGRAM VERSION: MacR6-Z0_H2.1.0_S001.04_V1307 MacR6-Z0-P_H2.0.1_S001.04_V1307 DOCUMENT REVISION: 12-2017 MacR6-Z0 & MacR6-Z0-P Pulse / pressure / temperature recorder USER MANUAL
…
MacR6-Z0(70 pages) |
Lloydspharmacy Personal Care Products SpotClear Advance LLAC1User Guide: Lloydspharmacy SpotClear Advance LLAC1 (W3365K, Upd.27/09/2023) SpotClear Advance LLAC1, 17 |
Buffalo Grill Instruction ManualBuffalo Instruction Manual Grill Gl Instruction Manual, 16 |
COBHAM Motherboard SPSC-EVB-R0COBHAM Motherboard SPSC-EVB-R0 Operation & user’s manual SPSC-EVB-R0, 31 |
Wow Speakers Wow-soundSpeakers #N556UW Wow-sound, 7 |
Philips Headphone SBC HN060#YW34G3: SBC HN060 Headphone Specifications SBC HN060, 2 |
BoschHome Cooktop nit8065ucBoschHome Product Manual: nit8065uc PDF Use and care manual - JXMTT6 nit8065uc, 87 |
Greenheck Industrial Electrical AMD-42-TDIndustrial Electrical PDF Installation, operation and maintenance manual AMD-42-TD, 12 |
Kohler Plumbing Product 72282T-4Kohler Plumbing Product Installation instructions manual (File: kohler-72282t-4-installation-instructions-manual-2, 29.12.2023) 72282T-4, 2 |
HP Switch J9311APDF Manual (@68CHD9), HP J9311A Switch (25th Aug 2023) J9311A, 72 |
Weider Other Pro 255 L BenchWeider Pro 255 L Bench Guide (Doc Type: Other Manual ) Pro 255 L Bench, 12 |
Panasonic Kitchen Appliances CZ-CENSC1CZ-CENSC1 Operating instructions manual - B827ZT CZ-CENSC1, 8 |
JBL Speaker System CINEMA SB200JBL CINEMA SB200 User Manual (Quick start manual), @4LJCKB CINEMA SB200, 8 |