Manualios.com

SHAREBOT Next Generation XXL+ Operation & User’s Manual

  • Next Generation XXL+ 3D Printers
  • ma.2O9Kmchm5M
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 41

SHAREBOT Next Generation XXL+ Manual Online:

4.15, 2979 votes
SHAREBOT Next Generation XXL+ User Manual
SHAREBOT Next Generation XXL+ User Guide
SHAREBOT Next Generation XXL+ Online Manual

Text of SHAREBOT Next Generation XXL+ User Guide:

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual 1 Presence filament sensor 2 Label with Identification Code (inside the printer, on the right part of the chassis) 3 Switch and power cable socket Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission page 10

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual How to calibrate the printing bed This operation, although at first a bit hard-working, it will become an habit for you that you will want to do before every prestigious print, taking only a few tens of seconds. With experience you might even make regulations "on the fly" while printing the first layer, if there is evidence of some Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission page 22

  • Sharebot Next Generation XXL+ user's manual The orientation Let's begin with a consideration about the orientation of 3D files in relation to the printing surface: the object is built layer by layer and so each new layer is supported by the one previously built. When a wa ll or a surface is tilted over 45°, or some parts ar e built without la yers supp

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual “Prepare” menu This menu is used to set up and manage the printer, such load and unload the filament, pre-heating the extruder and the printing bed, launching 'autohome or moving all the different axis. In practice, you have complete control of the printer and you can perform all management and maintenance operations. Info screen Change filament Disable steppers Autohome Preheat: – Preheat all – Preheat bed Cool down Move axis Move down plate Test Plate (level plate) Check

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual The “slices” are saved in a specific format (called G-Code); This format is nothing more than a set of instructions for moving the instrument (extruder head) along a path X, Y, and Z axes. Each slice contains the movements on two axes, the moving the of the plane and the commands of the motor that extrudes the plastic to create one by one the layers that make up the object. Every 3D object can be transformed with the process of slicing in a variety of

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Opening the package Your Sharebot XXL+ is equipped with a series of accessories that allow you to make it immediately operative; there is no software because it is open source and constantly updated. Software must be downloaded from the Sharebot website to always have the latest version . Alternatively, we recommend the purchase of Simplify3D from our website to take advantage of the potential of Sharebot XXL+. With care and without damaging the packaging remove the various parts and elements that fix the printer inside the package and then - helped by another person - pull it out by the two s

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Printing plate The first layer of the object that we print is crucial for the success of printing: for this reason the printing surface must be perfectly smooth, with a uniform layer of hairspray applied. After many prints, layers of hairspray overlap each other and together with the residues of the printed parts compromising the flatness of the surface of the printing glass by creating irregularities: paying attention you can wash the printing glass with warm water and remove any remaining impurities. Regulation of pressure upon filament The cogwheel of the motor of the extruder and the relative am

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Lubrication.................................................................................................................................................................................................38 Belts tension.............................................................................................................................................................................................39 Checking of proper ventilation.............................................................................

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Downloading from internet Internet offers many ready-made 3D models, but also in this case there are differences between the models that you “see fine” and those who “print well”. A good indicator of the ability to print the file extension: the most popular 3D printing is STL (websites that intend to offer printable objects use this format). If there is no STL it is likely that the intended use is different and the result on a 3D printer is not guaranteed. From a 3D model to a printing file The real “secret” of three-dimensional printing is the transformation of three-dimensional object into a sequence of two-dimensional

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Now that the filament is inserted, dock again the PTFE guide. In case you want to print with the check filament sensor disabled, you can load the filament bypassing the sensor itself, positioning the spool-holder in a upper position, in such manner that the filament reaches all the print area smoothly. Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior p

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual C Report the danger of mechanical moving parts. D Report the danger of crushing at the point where the machine is located. E Report the danger to the presence of hot surfaces at the point of the machine where it is placed. Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission page 41

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Detach the printed part When printing is complete, your Sharebot XXL+ positions the platen down and park the extruder. In this position you can easily extract the printing glass after removing the clips to detach the printed object it from. This operation is delicate and inevitable: to complete correctly the printing , it's necessary that the first layer adheres well and remains attached to the printing glass for the entire duration of the process. If there was not a good grip, t

  • Sharebot Next Generation XXL+ user's manual Let's print! Press the control knob and select "SD card menu". You can now read the contenent of the SD card, files and folders. Chose the file you want to print by pressing the control knob on it, and the printing process starts. Your Sharebot XXL+ starts heating the extruder and the printing bed while executing an a

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual “Tune” menu The item is displayed only while the machine is printing; the commands we find in are: Info Screen Check filament: ON/OFF Change filament Fan speed Nozzle Bed Flow Speed The first voice is about the sensor that monitors the presence of the filament. When the sensor no longer detects the filament, the printer goes automatically into change filament procedure (identical to that described afterwards); the buzzer sounds and the printer waits to receive the new filament just for 24 hours. By pressi

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual ATTENTION – EXTRUDER The fusion and extrusion system of the thermoplastic filament requires a heated end up to temperatures of 250 degrees and more. The contact, even for a very limited time, with the heated part causes burns. You must avoid to put your hands or other body parts in the printing area when printing and for minutes after the printing process is over. The current temperature of the extruder is indicated on the LCD screen. ATTENTION – HEATED PRINTING BED All the printing plate is made of metal with the addition of a glass plate. This device is electrically heated and s

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual calibration without hindering the movement of the bridge. The procedure continues by drawing the diagonals of the rectangle and then two circles, taking about 8 minutes. Adjusting pression force on filament Your Sharebot XXL+ is equipped with an amortized bearing opposed to the extruder cogwheel. This solution allows to compensate irregularities in thickness that some filaments may present, helping the dragging of it. The correct pression already regulated when you receive the printer.

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual For further details, please consult the Simplify3D user's manual or our dedicated course: www.sharebot.it/index.php/events/event/corso-simplify3d 7 - Printing behaviour of thermoplastic materials One of the most critical factors in the current 3D printers is the surface treatment of the printing plate. When the filament is extruded, the first layer must be daub by the nozzle on the printing surface.; i f by cooling down, the plastic loses grip, the printing process can fail, or decrease in quality, because of the detachment of th

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Version 0.4 - 06/2017 Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission page 1

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Plate levelling (calibration)...................................................................................................................................................23 Adjusting pression force on filament..............................................................................................................................................24 5 – Our first 3D printing....................................................................................................................................................................................

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Positioning the printer For proper operation, the printer must work in a clean and dust-free space, with an ambient temperature between 10° C and 30° c. It is also preferable a position away from drafts or air conditioning. In the left back you’ll find power switch so we recommend to leave it easily accessible; the power cable is the only way of separation of the plug from the mains. A t the front -bottom left – and on the left side of the printer, you will find the ventilation

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Indice generale ATTENTION – EXTRUDER..................................................................................................................................................................................2 ATTENTION – HEATED PRINTING BED........................................................................................................................................................2 Support Policies ..............................................

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual Fundamental parameters of Slic3r  Layer height: in the "print settings" tab you find "layers and perimeters" menu and the "layer height" voice; this is the height of the single layer and determines the printing resolution (for those curves developed in Z) and, consequently, the printing time. The default value is 0.3 mm and is recommended for all prints with Sharebot XXL+ because of its large print area.  Fill density: in the next menu, "infill", the item "fill density" concerns the internal material infill of O

  • Sharebot Next Generation XXL+ user's manual irregularity in thickness. A cquiring the right sensitivity for the calibration of the printing plate, even just looking frontally, it will be an advantage for you and potential warranty for prints always optimal. Plate levelling (calibration) From the "prepare" menu select "Test plate": the procedure prints concentric rectangles

  • SHAREBOT Next Generation XXL+, Sharebot Next Generation XXL+ user's manual “Nozzle” is to set the temperature of the nozzle: the value is in degrees Celsius and any change must be confirmed by pressing the menu knob. Same thing for following item, the heated bed. “Flow” is relative to the percentage increment or decrement of the extrusion phase: the slicing software calculates exactly how the material is extruded to create individual layers, but with this item we can "get fat" or "lean" the print as we prefer. The last item is about the printing speed: we can change the percentage of all the speeds of the gcode. It is identical to the one that we can change directly in

  • Sharebot Next Generation XXL+ user's manual 7 SD card slot 8 LCD control knob 9 Glass printing bed 10 Lateral ventilation of electronic 11 USB connection (only for update) Sharebot srl Nibionno Italy All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission page 9

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Shindaiwa T344 Owner's/operator's manual shindaiwa/t344-W36.pdf 09 Apr 2023 28 1.96 Mb
2 D-Link DSS-24+ Operation & user’s manual d-link/dss-24-B45.pdf 15 Oct 2023 35 0.49 Mb
3 Frigidaire FFC05M2AW0 Factory parts catalog frigidaire/ffc05m2aw0-QZG.pdf 22 May 2023 7 0.41 Mb
4 CrimeStopper CS-5502 Wiring instruction crimestopper/cs-5502-R37.pdf 04 May 2023 1 0.04 Mb
5 Whirlpool FEP340Y Use and care manual whirlpool/fep340y-92G.pdf 02 Sep 2022 28 1.34 Mb
6 Blanco BCGC74 - BCGC52 Use, installation and maintenance instructions blanco/bcgc74-bcgc52-77T.pdf 23 Sep 2022 13 0.62 Mb

Similar Resources:

  • WEEDO

    TINA 2

    (41 pages)
    1JIANGSU WIIBOOX TECHNOLOGY CO.,LTD◆ This user manual is for standard TINA 2.◆ Because of software or hardware upgrades and modeldifferences, new revisions may not be listed in this guide.3D PRINTERTINA 2USER MANUAL …
  • XYZ Printing

    da Vinci 1.0 Pro 3in1

    (28 pages)
    da Vinci 1.0 Pro 3in1User ManualENGProduct Safety Product Description Printer screen menu, functions and messagesFunctional operations and descriptions PrintScanOptional module Support Details Product …
  • iBox

    JG Titan MKII V2

    (5 pages)
    JG Titan MKII V2 „single“ Montage / AssemblingDemontieren Sie jetzt alle Anbauteile des Kühlkörpers. Schrauben Sie nun das Aluminium Ver-bindungsstück des Extruders ein. (Muss zuvor aus Extruder demontiert werden). Schrauben Sie anschließend die neue Heatbrake mit bündig eingesetztem HD Tube in den Kühlkörper ein und setzen Sie den Extruder-Hals a …
  • MiiCraft

    Hyper Series

    (12 pages)
    3D production system ► Make a better world 1 Hyper series / Prime series 3D Printer User Manual for Hardware Version 1.0 …
  • Z Corporation

    D4

    (4 pages)
    ZD4 Operations Manual Z CORPORATION09503 Revision A11.1. DESCRIPTION OF OPERATIONZD4 System:Purpose: The ZD4 Depowdering Station assists in the removal of powder from parts createdwith Z Corporation 3D Printers. There are, essentially, two modes of operation: theDepowdering Station allows you to blow loose powder off your parts with compressed air, …
  • WANHAO

    Duplicator 5S

    (2 pages)
    Hold ,then press or to scroll through options. represents Heating Mode, represents Cooling Mode.Power IndicatorLCD LayoutOperation1.Set Target Temperature:2.Second Menu:Press gently to blink display the to change the target target temperature.Now press or temperature.Hold for 6 seconds to enter seco …

3D Printers Instructions:

Comments, Questions and Opinions: