Manualios.com

Z Corporation Spectrum Z 510 Maintenance Manual

Z Corporation Spectrum Z 510 Manual Online:

4.3, 1565 votes
Z Corporation Spectrum Z 510 User Manual
Z Corporation Spectrum Z 510 User Guide
Z Corporation Spectrum Z 510 Online Manual

Text of Z Corporation Spectrum Z 510 User Guide:

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 1/12 80563 Spectrum Z510 Preventative Maintenance Procedure Rev D Description: This procedure is for the purpose of preventative maintenance on the Spectrum 510. Prerequisites: • Printers should be inspected for bulletin updates before ordering parts for maintenance. • Bulletins can be found on the Z Corp Website. Equipment / Parts Required: • 50342 Dealer Recommended Toolkit. • 50355 Spectrum Z510 Maintenance Kit. • 10674 Syringe, Luer-Lock, 20cc (Accessories Kit) • 06775 PL Needle Tubing Assy (Accessories Kit) • 0994

  • 85063 Spectrum Z510 Preventative Maintenance Procedure 2/12 1.Fast Axis Module Document #s/Notes Clean rails Clean Bumpers Clean Pulleys with dental pick Careful not to scratch the metal Grease Fast Axis Check Fast Axis for smoothness Reset maintenance reminder Clean Pogo Card Check Pogo Pins for springiness

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 3/12 6.Pistons Document #s/Notes Grease piston screw Reset maintenance reminder Rezero piston External keyboard and monitor (manufacturing Window) 7.While Printing Document #s/Notes Run alignment Check for streaks Check for short spread/over spread Check for smooth spread Check rails for noise Additional Comments: Technicians signature:______________________________________________ Customer Signature:______________________________

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 4/12 Changing the Septa Remove the print heads from the carriage. Remove the fast axis from the machine Cover the binder hose plug with paper towels and secure with a rubber band. Place a paper towel inside the assembly to soak up any stray binder. Pull all the binder tubes loose from the septa. Note- make sure you have your paper towels handy. When the tubes are pulled from the septa, binder will leak from the tubes.

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 5/12 Remove the four e- rings that retain the septa. Note – be careful not to lose the plastic washers that are attached to the top side of the septum. Old septum shown with the four plastic washers that must be re-installed on new septa before installation. Septum being removed. Note – The plastic washer tends to stick to the carriage. Do not lose them.

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 6/12 Install the septum (septa). Note – you will have to insert the L shaped connector in the hole first by holding it on an angle, and then straighten it out as the connection area passes the hole. Make sure each has the plastic washer attached. Hold the septa in place, and attach all four e-ring clips. Loop the yellow tube over the top of the clear. This lessens the amount of pinching force on the base of the yellow tube. Some carriages may have the yellow tube going under the clear. If so, please re-route at this time. Re-attach the

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 7/12 Clean all the pogo connections with the alcohol crush tubes. Clean up any binder on the bottom of the carriage, and make sure the alignment window is clean. Re-install the Fast axis module and pull several syringes of binder through the septa to clear all air bubbles. Re-install the print heads (purge if new heads) Run an auto- alignment.

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 8/12 Service Station Wiper Remove/Replace This is the service station wiper. It is one of the components in the maintenance kit. Raise the old wiper up and out of the way. Remove the two hex screws that mount the assembly into place. Note – The ZPrinter 510 and ZPrinter 650 use the same wiper assembly, and the mounting screws and method is the same.

  • 85063 Spectrum Z510 Preventative Maintenance Procedure 9/12 Remove the squirter block, clean it and clean the holes with the tip of the syringe tool. Clean the holes from both sides. Align the rubber wiper with the holes in the squirter block and wrap around the block.

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 10/12 Once aligned, insert both mounting screws into place to hold the assembly together. Tighten both screws evenly. (see next picture for clarification) Note – The ZPrinter 510 and ZPrinter 650 use the same wiper assembly, and the mounting screws and method is the same. As you tighten the two screws (alternate to keep the pressure even) you will notice that the rubber bulges out from underneath the mount. When properly tightened, the rubber will extend by nearly 1/8 inch. This should be a visual indication that the pressure is even on the two screws and th

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 11/12 Testing the flow rate 1. SET UP: From ZPrint, choose Bleed Air from the service menu, then click Start (this will move the carriage to the front of the machine and prevent it from auto parking even when you close the top cover. The safest option is to power down the printer and manually move the carriage to the front, right side of the deck. 2. CHECK: Make sure there is some binder in the bottles for the line you are testing. 3. INS

  • Z Corporation Spectrum Z 510, 85063 Spectrum Z510 Preventative Maintenance Procedure 12/12 Change History REV ECN Name Date Rev A 2637 BWH 12/23/08 Rev B 2881 BWH 9/25/09 Rev C 3134 BWH 4/13/11 Rev D 3146 BWH 5/24/11 Information contained in this document is the confidential property of Z Corporation. Recipient shall not disclose such Information to any third party, and shall not use it for any purpose whatsoever other than to price or provide services to Z Corporatio

More Instructions:

DOWNLOAD

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Electro-Voice Compact Precision CP1200 Owner's manual electro-voice/compact-precision-cp1200-19R.pdf 13 Jan 2023 36 2.38 Mb
2 Bayliner 185 Owner's manual bayliner/185-4N4.pdf 09 Apr 2023 56
3 Q-See QR series Operation & user’s manual q-see/qr-series-KYS.pdf 13 Jul 2023 22 4.39 Mb
4 Samsung HL-S5065W Owner's instructions manual samsung/hl-s5065w-5XX.pdf 23 Jan 2024 120 10.73 Mb
5 NordicTrack E7.0 Elliptical Manual  nordictrack/e7-0-elliptical-97Q.pdf 18 Oct 2022 32
6 Iqua Snake� 2 HHF-601 Specifications iqua/snakea-a-2-hhf-601-59O.pdf 18 Jul 2023 1

Similar Resources:

  • MUTOH

    XpertJet XPJ-1641SR

    (150 pages)
    CSTM-XPJ16xxSR(E)_1.00 CONFIDENTIAL Page. To Table of Contents 1 MUTOH INDUSTRIES LTD Training Manual History Rev.1.00 26.July.2019 Rev. 1.00 Date 26.July.2019 Date ◆First version …
  • BIGREP

    ONE

    (4 pages)
    Your First Print: The Toolbox I. WHAT YOU NEED 1. 2. 3. The Ocke Print Folder – available here – that contains: • The PLA 1 mm nozzle Presetting .factory file • The Toolbox .stl file A spool with more than 50 g of 2.85 mm PLA filament. Choose the color you like from our online shop here! Install Simplify3D. If you don’t have …
  • XYZ Printing

    ds Vinci Color

    (14 pages)
    Important Safety Precautions 2Product exterior 2Specications 3Unpacking 4Main screen 6WiFi setting 7Print bed calibration (leveling) 8Z-offset check 8Load laments 8Ink Installation 9Change Ink 10Print test page 10Color calibration 11Ink Calibration 11Convert and slicing le 12Printing 12Problem code and handling 13XYZprinting 3D …
  • FLASHFORGE 3D PRINTER

    Hunter

    (62 pages)
    FlashForge Corporation Hunter User Guide | www.flashforge.com …
  • PhotoCentric

    Liquid Crystal Dental

    (11 pages)
    2205 West Parkside Lane, Phoenix, 85027, AZ USAwww.photocentricgroup.usCambridge House, Oxney Road Peterborough PE1 5YW [email protected] USADISPOSAL INSTRUCTIONSDo not throw this electronic device into the waste when discarding. To minimize pollu-tion and ensure utmost protection of the global environment, please recycle …
  • m3d

    PRO

    (23 pages)
    Extruder Gear Replacement Guide for the M3D PRO In this guide we will explain how to replace the extruder gear for your M3D PRO. You will need a 2.0mm/1.5mm hex screwdriver for the disassembly and you’ll want to be in a antistatic environment. Some electronics will be exposed during the disassembly and there is a chance you could damage them. We recommend …

Comments, Questions and Opinions: