Tytan DS 512 Installation Manual

Text of Tytan DS 512 User Guide:

• 2 tytan TYTAN DS512 CAN GPS GSM CAN-bus Vehicle Security System (VSS) and GSM-SMS Pager features • GSM-SMS pager integrated with CAN-bus Vehicle Security System central unit, • alarming state signalisation with SMS messages in GSM network, • external GPS receiver (optional), • remote (SMS) control of VSS and remote access to VSS trigger so

• Tytan DS 512, Digital Systems 3 GENERAL • Tytan DS512 was designed to use in all vehicles with 12V/24V power supply system and negative ground. • Tytan DS512 must be installed according to the manufacturer’s requirements and documentation. • It is suggested to install the DS512 only by an authorized person or company. The list of authorised installers can be obtained from manufacturer or distributor of Tytan DS512 CAN. It should be checked, if the installation certificate, delivered with the system has been filled in by the installer. • The

• Tytan DS 512, 4 tytan 1. DS512 OPERATING PRINCIPLE The DS512 is a device, that combines function of a complete Vehicle Security System (VSS) and the SMS pager. The general purpose of DS512 is to notify up to 3 mobile phone numbers with SMS information containing status of vehicle and status of equipped security system. The DS512, can be equipped with external GPS receiver. This allows to receive vehicle geographical position in the form of latitude and longitude. SMS notification also includes a link to online maps, w

• Tytan DS 512, Digital Systems 5 Mode 1 - ANALOGUE PAGER The DS512 operates as an analogue pager to any VSS installed in the vehicle. Detection of alarming in the monitored VSS causes the DS512 to notify up to 3 users with a SMS about alarming. There is no audible nor visible signalisation in this mode. The device does not react on opening the door or switching on the ignition as long as it does not trigger the OEM alarm. The information on triggering alarm is read from analogue signal. The possible triggering conditions are: positive signal NO, positive signal NC, ground signal NO, ground signal NC. The signal must be at least 1 sec. long

• Tytan DS 512, 6 tytan Parameter list: 2.1. Operating mode The parameter selects the operating mode of DS512 as described above (analogue pager / CAN-bus Pager / Silent Alarm / Full Alarm). 2.2. Selection of vehicle type In order to operate correctly with the vehicle CAN-bus in CAN-bus based modes (2,3,4), the DS512 has to be programmed to a given vehicle model with so-called ‘CAN level’. The CAN-bus level can be selected according to the table or the wiring diagram for a given vehicle. Moreover, it can

• Tytan DS 512, Digital Systems 7 - power windows. The information which vehicles allow for CAN bus control and which circuits can be activated is present on the vehicle list and on wiring diagrams 2.6. Audible confirmation of arming/disarming The parameter enables acoustic signalisation of arming/disarming VSS with short siren chirps. IMPORTANT! Audible confirmation can be enabled only in countries where the Reg. 97 does not apply. In opposite case, the homologation of DS512 as a VSS becomes invalid. 2.7. Power windows roll-up The parameter enables power windows roll-up when the system is armed. In order to op

• Tytan DS 512, 8 tytan Depending on the configuration of parameters 6,7,8, the information on ignition state, combined door/trunk/bonnet state and armed/disarmed state will or will not be included in the SMS sent from DS512. If parameter 7 is set to ‘no’ the information on system status will be sent only as: If it is set to ‘yes’, the information on system status will be more detailed: Moreover, even if the alarm is not triggered at the moment, but the alarm was triggered at least once since the vehicle was armed, the additional information will be placed in the SMS: In

• Digital Systems 9 ALARM The DS512 in mode 3 and 4 (operating as VSS) has detected alarm condition and is alarming. ALARM_OEM The DS512 has detected, that OEM CAN VSS has been triggered (modes 2,3,4) . ALARM_PAGER The DS512 has detected, that monitored analogue VSS has been triggered and is alarming (mode

• 10 tytan Column 8 shows the status of optional equipment: RF module with analogue central door lock control outputs and external sensor No2 inputs Lamp Description RMT_LOCK The lamp shows that LOCK button on Tytan remote transmitter was pressed RMT_UNLOCK The lamp shows that UNLOCK button on Tytan remote transmitter was pressed RMT_TRUNK The lamp sh

• Tytan DS 512, Digital Systems 11 5. PROGRAMMING OF TYTAN REMOTE TRANSMITTERS The DS512 can be equipped with additional RF receiver module, handling the Tytan remote transmitters. The RF module is automatically paired with DS512: - when the DS512 is restarted. Please keep in mind, that to restart DS512 all power supply sources must be disconnected: the main power supply, internal battery and USB connector. - when the RF module button is pressed on the dedicated PC software and the RF receiver diagnostic monitor is opened. In order to program the remote transmitters, open the RF module panel and press the Save

• Tytan DS 512, 12 tytan 8. BASIC SMS COMMANDS The DS512 can be controlled by SMS commands sent from any mobile phone. The commands are described in details in User Manual. The commands begin with 5-digit VSS PIN code (Important! Not to be confused with SIM card PIN!). The VSS PIN code prevents DS512 from unauthorised access. Default VSS PIN code is 12345. In this document, 2 basic commands, applicable for device testing will be shown. DS512 Status Basic method of testing the DS512 SMS commands functiona

• Tytan DS 512, Digital Systems 13 where: current VSS PIN current (old) VSS PIN or default VSS PIN (12345) in the device new VSS PIN VSS PIN which will be set as the new one number of mobile phones number of mobile phones, which receive SMS with information when the alarm is triggered in the vehicle 0-3 first phone number, second phone number, third phone number mobile phone numbers which are informed about triggering the alarm in the vehicle in international form

• Tytan DS 512, 14 tytan 10. GIVING THE SYSTEM TO THE USER After the system is installed and checked, the user must be informed about operation of the system, the meaning of VSS PIN code and obliged to change individual VSS PIN code, mobile phone numbers, number of mobile phones and to test operation of at least status or localisation SMS command. After that the SMS Paging must be tested. 11. TECHNICAL DATA Power supply: 9-30V Mean (300 seconds) power consumption at 12V

More Instructions:

Tytan DS 512 Operation & user’s manual 12-02-2024 10

DOWNLOAD

Related Products and Documents (Car Alarm):

Comparable Devices:

Similar Resources:

• Carbine PLUS-6900 (20 pages) User’s ManualModel: PLUS-6900This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; and(2) This device must accept any interference received, including interference that may cause undesired operation.Note: The manufacturer is not responsible for any radio …

• Toyota TVSS V (71 pages) TVSS VTOYOTA VEHICLE SECURITY SYSTEMEINBAUANLEITUNG TEIL 1INSTALLATION INSTRUCTIONS PART 1NOTICE EXPLICATIVE DE L’INSTALLATION PARTIE 1CorollaLHDTEILENUMMER - PART NUMBER - NUMERO DE PIECEFÜR-FOR-POUR **E12-A*L + **E12-D*L Manual Ref. Nr. T5LE12AD/J-A0-2500HAUPT-EINBAUSATZ(Nur für Belgien)MAIN KIT (Only for Belgium)08585-12980EQUIPEMENT PRINCIPAL(Belgiq …

• nedis DUMSM10WT (37 pages) DUMSM10WTMANUAL (p. 2)ANLEITUNG (S. 4)MODE D’EMPLOI (p. 6)GEBRUIKSAANWIJZING (p. 8)MANUALE (p. 10)MANUAL DE USO (p. 12)MANUAL (p. 14)HASZNÁLATI ÚTMUTATÓ (o. 16)KÄYTTÖOHJE (s. 18)BRUKSANVISNING (s. 20)NÁVOD K POUŽITÍ (s. 22)MANUAL DE UTILIZARE (p. 24)ΕΓΧΕΙΡΙΔΙΟ XPHΣHΣ (σελ. 26)BRUGERVEJLEDNING (s. 28)VEILEDNING (s. 30)INSTRUKCJA OBSŁ …

• Webasto Thermo Top C (28 pages) WARNING!Hazard warning:Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result.Specialist company training, technical documentation, specialized tools and equipment are required to install and repair Webasto heating and c …

• Mopar EVS (13 pages) Note: It is recommended that this installation take place prior to rustproofing.The individual delivering the vehicle should review theoperation of this security system and any optionalfeatures with the owner of the vehicle. Please place theoperating instructions in the glove compartment with thevehicle Owner's Manual.Please review these instructions co …

• Directed 4113, 1-button series (20 pages) This product is intended for installation by a professional installer only! Attempts to install this product by a per-son other than a trained professional may result in severe damage to a vehicle’s electrical system and components.© 2012 Directed, Vista, CA N4113 2012 01N4111 2012 01Installation GuideKeyless Entry Remote Start4113, 1-button series …

Comments, Questions and Opinions: