Panasonic S-80MW1E5 Installation Instructions Manual
|
Panasonic S-80MW1E5, ȖȯȠȘȕȥȦȟȝ ǏǕǕǑǗǓǔǤ PORTUGUÊS NEDERLANDS ITALIANO DEUTSCH ESPAÑOL FRANÇAIS ENGLISH Air-to-Water Heatpump ■ R410A Models Model No. Indoor Units Type Indoor Unit Type Rated Capacity 80 125 W1 Air-to-Water S-80MW1E5 S-125MW1E5 ENGLISH Read through the Installation Instructions before you proceed with the installation. In particular, you will need to read under the “IMPORTANT!” section at the top of the page. FRANÇAIS Lisez les instructions d’installation avant de commencer l’install
Panasonic S-80MW1E5, 2 IMPORTANT! Please Read Before Starting This Air-to-Water must be installed by the sales dealer or installer. This information is provided for use only by authorized persons. Be sure to read the installation instructions relevant to the VRF system connected to this Air-to-Water and all appliances connected to the VRF system. For safe installation and trouble-free operation, you must: ● Carefully read this instruction booklet before beginning. ● Follow each installation or repair step exactly as shown. ● This Air-to-Water shall be installed in accordance with National Wirin
Panasonic S-80MW1E5, 3 ENGLISH When Installing… Select an installation location which is rigid and strong enough to support or hold the unit, and select a location for easy maintenance. …In a Room Properly insulate any tubing run inside a room to prevent “sweating” that can cause dripping and water damage to walls and floors. CAUTION Keep the fire alarm and the air outlet at least 1.5 m away from the unit. …In Moist or Uneven Locations Use a raised concrete pad or concrete blocks to provide a solid, level foundation for the outdoor unit. This prevents water damage and abnormal vibration. …In an Area with High Winds Securely anchor the outdoor unit d
Panasonic S-80MW1E5, 4 IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent gases into the atmosphere. Refrigerant type: R410A GWP (1) value: 1975 (1) GWP = global warming potential Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please contact your local dealer for more information. Sample label: MF2 type outdoor unit Please fill in with indelible ink, ■ 1 the factory refrigerant charge of the product ■ 2 the additional refrigerant amount charged in the field and ■
Panasonic S-80MW1E5, 5 ENGLISH CONTENTS Page Page IMPORTANT! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Please Read Before Starting IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1-1. Main Components 1-2. Tools Required for Installation (not supplied) 1-3. Accessories Supplied with Unit 1-4. Field Supply Accessories 1-5. Type of Copper Tube and Insulation Material 1-6. Additional Materials Required for Installation 2. SELECTING THE INSTALLATION SITE . . . . . . . . . . . 8 2
6 1. GENERAL This booklet briefly outlines where and how to install the Air-to-Water system. Please read over the entire set of instructions for the indoor units and make sure all accessory parts listed are with the indoor units before beginning. 1-1. Main Components Indoor unit 1. PCB (Main) 2. PCB (Relay Board) 3. PCB (3WAY) 4. Pressure relief valve 5. Flow switch
Panasonic S-80MW1E5, 7 ENGLISH 1-2. Tools Required for Installation (not supplied) 1. Flathead screwdriver 2. Phillips head screwdriver 3. Knife or wire stripper 4. Tape measure 5. Carpenter’s level 6. Sabre saw or keyhole saw 7. Hacksaw 8. Core bits 9. Hammer 10. Drill 11. Tube cutter 12. Tube flaring tool 13. Torque wrench 14. Adjustable wrench 15. Reamer (for deburring) 1-3. Accessories Supplied with Unit No. Accessories Qty. No. Accessories Qty. No. Accessories Qty. a Installation plate 1 d PS Foam 2 g Drain elbow 1 b Screw 3 e Long Banding Strap 4 c Installation plate 1 f Packing 1 1-4. Field Supply Accessori
Panasonic S-80MW1E5, 8 1. The indoor unit must be within a maintenance space. [ ] Drain Hose 300 mm or more 300 mm or more 300 mm or more ø9.52 mm (3/8”) Liquid Refrigerant Piping ø15.88 mm (5/8”) Gas Refrigerant Piping Water Inlet piping Water Outlet piping Check that all the cables do not touch the hot piping, etc. Cable list: ● Power Supply cable ● Inter-unit control wiring ● Remote controller wiring ● MINI Seri-Para I/O wiring ● Other cable ● 2-way Valve cable ● Room Thermostat cable ● External Controller cable Optional Type designation 60245 IEC 57 or heavier cable 2. SELECTING T
Panasonic S-80MW1E5, 9 ENGLISH 3-2. How to Fix Installation Plate The mounting wall is strong and solid enough to prevent it from vibration. Washer Wall Wall Installation plate a Installation plate c Indoor unit body Wall 745 71 160 200 6 6 1550 from ground More than 551 More than 551 (Unit: mm) Bolt-size M8 Bolt- size M8 Appropriate Plugs (M8) The centre of installation plate should be at more than 551 mm at right and left of the wall. The distance from installation plate edge to ground should more than 1550 mm. ● Always mount the installation plate horizontally by aligning the m
10 Water Piping Installation of Air-Conditioning mode Water Piping Installation of TANK mode Water Inlet Tank Unit Panasonic Air-to-Water Heatpump Indoor Unit External Filter (Field Supply) Water Outlet High-Spec Wired Remote Controller (CZ-RTC5) ● Be sure to use two spanners to tighten the connection. Tighten the nuts with torque wrench: 117.6
Panasonic S-80MW1E5, 11 ENGLISH 3-8. Drain Elbow and Hose Installation ● Fix the drain elbow g and packing f to the bottom of indoor unit, as shown in below illustration. ● Use inner diameter 17 mm drain hose in the market. ● This hose must be installed in a continuously downward direction and in a frost-free environment. ● Guides this hose’s outlet to outdoor only. ● Do not insert this hose into sewage or drain hose that may generate ammonia gas, sulfuric gas, etc. ● If necessary, use hose clamp to further tighten the hose at drain hose connector to prevent leakage. ● Water wil
Panasonic S-80MW1E5, 12 4-3. Wiring System Diagram N OT E (1) Refer to “4-2. Recommended Wire Length and Wire Diameter for Power Supply System” for the explanation of “A”, “B” and “C” in the above diagram. (2) The layout of terminal boards in your equipment may differ from the diagram. Be sure to confirm the actual terminal boards. (3) Refrigerant Circuit (R.C.) address should be set before turning the power on. (4) Regarding R.C. address setting, refer to the installation instructions supplied with the outdoor unit. Auto address setting can be executed by remote controller automatically. (5) Sub-remote controller cannot be connected. (6) Gro
13 ENGLISH CAUTION (1) When linking the outdoor units in a network, disconnect the terminal extended from the short plug from all outdoor units except any one of the outdoor units. (When shipping: In shorted condition.) For a system without link (no wiring connection between outdoor units), do not remove the short plug. (2) Do not install the inter-unit c
Panasonic S-80MW1E5, 14 How to connect wiring to the terminal ■ For stranded wiring (1) Cut the wire end with cutting pliers, then strip the insulation to expose the stranded wiring about 10 mm and tightly twist the wire ends. (2) Using a Phillips head screwdriver, remove the terminal screw(s) on the terminal board. (3) Using a ring connector fastener or pliers, securely clamp each stripped wire end with a ring pressure terminal. (4) Place the ring pressure terminal, and replace and tighten the removed terminal screw using a screwdriver. ■ Examples of shield wires (1) Remove cable coat not to scratch braided sh
15 ENGLISH 5. HOW TO PROCESS TUBING 5-1. Connecting the Refrigerant Tubing Use of the Flaring Method Many of conventional split system air conditioners employ the flaring method to connect refrigerant tubes which run between indoor and outdoor units. In this method, the copper tubes are flared at each end and connected with flare nuts. Flaring Procedure with a Flare Tool (
Panasonic S-80MW1E5, 16 CAUTION After a tube has been insulated, never try to bend it into a narrow curve because it can cause the tube to break or crack. 5-4. Taping the Tubes (1) At this time, the refrigerant tubes (and electrical wiring if local codes permit) should be taped together with armoring tape in 1 bundle. (2) Wrap the armoring tape from the bottom of the outdoor unit to the top of the tubing where it enters the wall. As you wrap the tubing, overlap half of each previous tape turn. (3) Clamp the tubing bundle to the wall, using 1 clamp approx. each meter. N OT E Do not wind the armoring tape too
Panasonic S-80MW1E5, 17 ENGLISH 6. HOW TO INSTALL THE HIGH-SPEC WIRED REMOTE CONTROLLER (OPTIONAL PART) 6-1. Installation Location ● Install at the height of 1 to 1.5 m from the floor (Location where average room temperature can be detected). ● Install vertically against the floor. ● When installing more than 1 remote controller next to each other, keep distance of 5 mm on the right and left and 50 mm on top and bottom. ● Avoid the following locations for installation. • By the window, etc. exposed to direct sunlight or direct air • In the shadow or backside of objects deviated from the room air flow. • Location where condensation occurs. The remote controller is
Panasonic S-80MW1E5, 18 2-1. Exposed type Preparation: Make 2 holes for screws using a screwdriver. Mount the top case. ● Align the claws of the top case and then align the claws of the bottom case. Connect the remote control wiring ● Arrange the wires along the groove of the case. Cut here with a nipper and remove the burr with a file. Wall to which the remote controller is fixed Claw (2 places) Claw (2 places) Bottom case (Back side) Remote controller terminal board Remove the coating. Approx. 6 mm Remove the sheath. Approx. 180 mm Make
Panasonic S-80MW1E5, 19 ENGLISH 7. TEST RUN ■ Test Run of Water Circuit CAUTION Panasonic Air-to-Water Heatpump Indoor Unit External Pump ● When external pump is used, be sure to install it in independent water circuit and not direct to the Air-to-Water heatpump indoor unit circuit. 7-1. How to Remove Front Plate Please follow the steps below to remove the front plate. Before removing the front plate of indoor unit, always switch off all power supply (i.e. indoor unit power supply, heater power supply and tank unit power supply). 1. Remove the 2 mounting screws which loca
Panasonic S-80MW1E5, 20 7-3. Initial Setting for Air-to-Water Unit * To complete the initial setting, it is necessary to carry out the Test Run for Water Circuit. * If the Test Run for Water Circuit is not complete, “L16” alarm will occur. 7-3-2. Test Run for Water Circuit * You cannot perform the test run of refrigerant circuit if test run for water circuit has not been completed. * First, pour water into the water circuit. High-spec Wired Remote Controller (CZ-RTC5) ƾ ƿ ʹʷƓʺʷƺƻ 1. Keep pressing the , and buttons simultaneously f
Panasonic S-80MW1E5, 21 ENGLISH • Air purge Press the or button to see each menu. If you wish to see the next screen instantly, press the or button. Select “Air purge” on the LCD display and press the button. > @6WDUW $LUWR:DWHUXQLW 7+8 6WDUWDLUSXUJH" $LUWR:DWHUXQLW 7+8 3XUJLQJDLU $LUWR:DWHUXQLW $LUSXUJH 3XPSVSHHGVHWXS &DQFHOLQWKHDWHUDODUP $LUWR:DWHUVHWWL
Panasonic S-80MW1E5, 22 7-4. Detailed settings for Air-to-Water (extract) High-spec Wired Remote Controller (CZ-RTC5) ƾ ƿ ʹʷƓʺʷƺƻ 1. Keep pressing the , and buttons simultaneously for 4 or more seconds. The “Maintenance func” screen appears on the LCD display. 0DLQWHQDQFHIXQF (&21$9,LQIR 2XWGRRUXQLWHUURUGDWD 6HUYLFHFRQWDFW 5&VHWWLQJPRGH 6HO 3DJH> @&RQILUP
Panasonic S-80MW1E5, 23 ENGLISH 1. Keep pressing the , and buttons simultaneously for 4 or more seconds. The “Maintenance func” screen appears on the LCD display. 0DLQWHQDQFHIXQF (&21$9,LQIR 2XWGRRUXQLWHUURUGDWD 6HUYLFHFRQWDFW 5&VHWWLQJPRGH 6HO 3DJH> @&RQILUP 7+8 2. Press the or button to see each menu. If you wish to see the next screen instantly, press the or button. Select “13. A
24 9. CHECK WATER PRESSURE *(0.1 MPa = 1 bar) Water pressure should not lower than 0.05 MPa (with inspects the pressure gauge 5). If necessary, add tap water into tank unit. Refer to tank unit installation instructions for details on how to add water. 10. CHECK PRESSURE RELIEF VALVE ● Check for correction operation of pressure relief valve by turning up the lever to
Panasonic S-80MW1E5, 25 ENGLISH ■ Error Code Code How to Release E03 Remote controller communication error Automatic E04 Abnormal indoor/outdoor communication error Automatic F01 Abnormal refrigerant sensor 1 (E1) Automatic F02 Abnormal water outlet sensor 1 (E2) Automatic F03 Abnormal refrigerant sensor 2 (E3) Automatic F10 Abnormal water intlet sensor (TA) Automatic F11 Abnormal water outlet sensor 2 (BL) Automatic L13 Mismatched indoor unit Reset (On and off of the power supply) L16 Test run for water circuit is not finished Do test run for water circuit L25 Unmatched remote controller Reset (On and off of the power supply) P07 Abnormal Internal heater overload Cancel from the remote co
Panasonic WH-SDF07C3E5 Heat Pump Service manual
WH-SDF07C3E5 |
Panasonic WH-MDF06D3E5 Heat Pump Operating instructions manual
WH-MDF06D3E5 |
Panasonic WH-MDC05F3E5 Heat Pump Service manual
WH-MDC05F3E5 |
Panasonic U-140PEY1E8 Heat Pump Operating instructions manual
U-140PEY1E8 |
Panasonic WH-MDC09C3E8 Heat Pump Service manual
WH-MDC09C3E8 |
Panasonic S-07MK2U6 Heat Pump Operating instructions manual
S-07MK2U6 |
Panasonic WH-SDF03E3E5 Heat Pump Design handbook
WH-SDF03E3E5 |
Panasonic U-8MF2E8 Heat Pump Service manual
U-8MF2E8 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | OTC Wireless | AVCW 100 | Quick start manual | otc-wireless/avcw-100-1U5.pdf | 09 Dec 2022 | 1 | |
2 | Closet Maid | Portable Closet 1095-31 | Installation instructions | closet-maid/portable-closet-1095-31-BR5.pdf | 09 Feb 2023 | 1 | 0.15 Mb |
3 | Sony | KV-29FX60A | Service manual | sony/kv-29fx60a-6EJ.pdf | 05 Jan 2024 | 4 | |
4 | Atlona | AT-HD14SS | Operation & user’s manual | atlona/at-hd14ss-343.pdf | 29 Dec 2022 | 11 | 0.99 Mb |
5 | Kenmore | 58714403400 | Installation instructions manual | kenmore/58714403400-EG6.pdf | 12 Sep 2023 | 12 | |
6 | Panasonic | DMC-TZ18 | Basic operating instructions manual | panasonic/dmc-tz18-ESW.pdf | 06 May 2023 | 15 |
Nordyne
13 SEER High Efficiency Split SystemThese units have been designed and tested forcapacity and efficiency in accordance with A.R.I.Standards. Split System Heat Pump units aredesigned for use with a wide variety of fossil fuelfurnaces, electric furnaces, air handlers, andevaporator coil combinations.Outdoor Air ConditionerUser’s Information and Installation …
13 SEER(12 pages) |
AERMEC
ISO 9001 - Cert. n° 0128/4IANPW07046755403_04Sostituisce il:Replace:6755403_03 / 0502MMMMAAAANNNNUUUUAAAALLLLEEEE TTTTEEEECCCCNNNNIIIICCCCOOOO EEEE DDDD’’’’IIIINNNNSSSSTTTTAAAALLLLLLLLAAAAZZZZIIIIOOOONNNNEEEETTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL AAAANNNNDDDD IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNN BBBBOOOOOOOOKKKKLLLLEEEETT …
AN R407C(72 pages) |
Dimplex
Luft/Wasser-Wärmepumpe für InnenaufstellungLIK 8TEAir-to-Water Heat Pump for Indoor InstallationPompe à chaleur air-eau pour installation intérieureMontage- und GebrauchsanweisungDeutschEnglishFrançaisInstructions d’installation et d’utilisationInstallation andOperating InstructionsBestell-Nr. / Order no. / No de commande : 452160.66.01 FD 9102
…
LIK 8TE(60 pages) |
IV Produkt
Industriventilation Produkt AB, Box 3103, SE-350 43 Växjö, SwedenPhone: +46 (0)470-75 88 00 email: [email protected] www.ivprodukt.seAir handling with the focus on LCCAir handling with the focus on LCCCooling Unit for Producing Chilled WaterEnvicooler®Operation and Maintenance Instructions 20010309E-D
…
Envicooler(15 pages) |
Danfoss
InstructionsCondensing Units Optyma™ Integral range© Danfoss | DCS (CC) | 2018.07FRCC.PI.059.A1.02 | 1MBP application50 Hz Compressor H W DOP-MCRN030OP-MCRN038MTZ018MTZ022545 630 650OP-MCRN048OP-MCRN054OP-MCRN060MTZ028MTZ032MTZ036705 900 900OP-MCRN068OP-MCRN086OP-MCRN096OP-MCRN108OP-MCRN121OP-MCRN136MTZ040MTZ050MTZ056MTZ064MTZ072MTZ080836.5 1200 800OP-MGR …
Optyma OP-MCRN030(9 pages) |
Hayward Pool Products
Model HP50CL Hayward Pool Products Canada, Inc.2880 Plymouth Dr., Oakville, ON L6H 5R4Haywardpool.ca / 1.888.238.7665SWIMMING POOL HEAT PUMP UNITInstallation & Instruction ManualHP65CLHP80CL
…
HP50CL(64 pages) |
Panasonic TV TX-32LX60FPDF User Manual (@S5F946), Panasonic TX-32LX60F TV (12th Oct 2023) TX-32LX60F, 56 |
Baxi Heat Pump AmbifloUser operating instructions manual for Baxi Ambiflo Heat Pump Ambiflo, 12 |
Craftsman Accessory 917.249790Craftsman 917.249790 Guide (Owner's manual), @36H8M8 917.249790, 16 |
REVELL Toy Saab J-35J DrakenAssembly manual for REVELL Saab J-35J Draken Toy Saab J-35J Draken, 11 |
KEPCO Power Supply HSF 5-20-1UKEPCO HSF 5-20-1U Manual (Instruction manual), @152491 HSF 5-20-1U, 4 |
MINOURA Other V100 - SCHEMATICSMINOURA V100 - SCHEMATICS User Manual (Manual ), @69Y39Q V100 - SCHEMATICS, 1 |
Sper scientific Measuring Instruments 850070Sper scientific Measuring Instruments 850070 Instruction manual 850070, 8 |
Philips Grooming kits G270Philips G270 Guide (Operation & user’s manual), @X687HW G270, 17 |
Vodavi Telephone Triad-S 1-2-3 Single LinePDF Guide (@792IZ2), Vodavi Triad-S 1-2-3 Single Line Telephone (Mon 01.2024) Triad-S 1-2-3 Single Line, 24 |
RecorderGear Kitchen Appliances PB500PDF User Manual (@9RV8D3), RecorderGear PB500 Kitchen Appliances (Tue 12.2023) PB500, 20 |
Oki Printer B930dn#4611ME B930dn: Oki Printer Owner Documentation B930dn, 229 |
Parkside Power Tool PDSP 1000 A1 SANDBLASTER GUNParkside PDSP 1000 A1 SANDBLASTER GUN User Manual (Operation and safety notes), @N7WLF4 PDSP 1000 A1 SANDBLASTER GUN, 89 |