Manualios.com

Kramer FC-10ETH Operation & User’s Manual

Kramer FC-10ETH Manual Online:

3.9, 886 votes
Kramer FC-10ETH User Manual
Kramer FC-10ETH User Guide
Kramer FC-10ETH Online Manual

Text of Kramer FC-10ETH User Guide:

  • Kramer FC-10ETH, FC-10ETH – Getting Started 3 2 Getting Started We recommend that you: • Unpack the equipment carefully and save the original box and packaging materials for possible future shipment • Review the contents of this user manual • Use Kramer high performance high resolution cables Go to Uhttp://www.kramerelectronics.comU to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate). 2.1 Achieving the Best Performance To achieve the best performance: • Use only good quality connection cables to avoid interference, deterioration in signal quality due to poor matching,

  • Kramer FC-10ETH,               �

  • 12 FC-10ETH - Configuring the FC-10ETH Ethernet Controller 4.3 Routing Data in the Passive and Active Routing Modes The FC-10ETH routes data in either the Passive Routing Mode (see Section 4.3.1) or the Active Routing Mode (see 4.3.2Section 4.3.1 The Passive Routing Mode ). In the Passive routing mode, the FC-10ETH never opens the Ethernet communication first, and only

  • Kramer FC-10ETH, 10 FC-10ETH - Configuring the FC-10ETH Ethernet Controller Figure 5: Connecting the FC-10ETH for Configuration 4.2.1 The Kramer Configuration Manager Window Figure 6: FC-10ETH Configuration Manager Window im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 Fax 07131 911203 [email protected]

  • Kramer FC-10ETH, FC-10ETH – Configuring the FC-10ETH Ethernet Controller 13 4. Set the Destin. IP and Port in the Destination Settings Area, for CHANNEL 1 and CHANNEL 2. 5. Press the Config button to accept changes. im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 Fax 07131 911203 [email protected]

  • Kramer FC-10ETH, FC-10ETH – Configuring the FC-10ETH Ethernet Controller 7 4 Configuring the FC-10ETH Ethernet Controller This section describes: • How to connect the FC-10ETH for configuration, via its ETHERNET port (see USection 4.1U) • How to install and run the Configuration Manager software (see USection 4.2U) • The Configuration Manager Window features (see USection 4.2.1U) 4.1 Operating via the ETHERNET You can connect to the FC-10ETH via Ethernet using either of the following methods: • Direct connection to the PC using a cro

  • Kramer FC-10ETH, FC-10ETH – Controlling Machines via the Ethernet using the FC-10ETH 15 6. Select either:  A virtual COM port if the control application cannot directly connect to the Ethernet driver (see USection 5.1.1U), or  An Ethernet port connection if the control application can directly connect to the Ethernet driver (see USection 5.1.2U) Figure 7: Connecting the FC-10ETH in the Passive Routing Mode 5.1.1 24BSetting a Virtual Port If the control application cannot work with an Ethernet driver, download the Kramer VSPM from our Web site to set a virtual port for each local port on your FC-10ETH. The Kramer VSPM software lets you emulate vi

  • Kramer FC-10ETH, 16 FC-10ETH - Controlling Machines via the Ethernet using the FC-10ETH 5.1.2 Setting an Ethernet Connection If the control application can directly connect to the Ethernet driver, select the host IP and port number according to your FC-10ETH configuration, as illustrated in Figure 8. Figure 8: The Port Window – Selecting a Remote Connection 5.2 Controlling a Kramer Machine via a Serial Controller To control a Kramer machine via serial controllers (in the Active routing mode), as illustrated in the example in Figure 9, do the following: 1. Connect the FC-10ETH (A) 12V DC power adapter to the power socket and co

  • Kramer FC-10ETH, 6 FC-10ETH - Overview # Feature Function 1 12V DC +12V DC connector for powering the unit 2 RS-232 COM 1 Port Connects to the RS-232 9-pin D-sub port on the Kramer (or other) device 1 or PC 3 ETHERNET Port Connects to your LAN 4 RS-232 COM 2 Port Connects to the RS-232 9-pin D-sub port on a Kramer (or other) device 2 or PC A Kramer device can be connected to either the RS-232 COM 2 port, or to the RS-485 terminal block port (but not to both) 5 RS-485 Terminal Block Port Connects to the RS-485 port on a Kramer (or other) device A Kramer device can be connected to either the RS-232 COM 2 port, or to the RS-485 terminal block port (but not to both) P

  • Kramer FC-10ETH, 18 FC-10ETH - Controlling Machines via the Ethernet using the FC-10ETH Figure 9: Connecting the FC-10ETH in the Active Routing Mode im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 Fax 07131 911203 [email protected]

  • Kramer FC-10ETH, FC-10ETH – Configuring the FC-10ETH Ethernet Controller 9 4.1.2 19BConnecting the ETHERNET Port via a Network Hub (Straight-Through Cable) You can connect the Ethernet port of the FC-10ETH to the Ethernet port on a network hub or network router, via a straight-through cable with RJ-45 connectors. 4.1.3 20BControl Configuration via the Ethernet Port To control several units via the Ethernet, connect the Master unit (Machine # 1) via the Ethernet port to the LAN port of your PC. Use your PC initially to configure the set

  • 4 FC-10ETH - Overview 3 Overview The high performance FC-10ETH Ethernet Controller is an easy-to-use, bidirectional hardware and software interface system for controlling Kramer (and also non-Kramer) RS-232 and/or RS-485 controllable machines via Ethernet LAN, as well as via the Internet. In particular, the FC-10ETH: • Offers network connectivity that lets you con

  • Kramer FC-10ETH, FC-10ETH – Contents i Contents 1 Introduction 1 1.1 Terminology Used in this User Manual 2 2 Getting Started 3 2.1 Achieving the Best Performance 3 3 Overview 4 3.1 Defining the FC-10ETH Ethernet Controller Front Panel 5 4 Configuring the FC-10ETH Ethernet Controller 7 4.1 Operating via the ETHERNET 7 4.2 Installing and Configuring the FC-10ETH 9 4.3 Routing Data in the Passive and Active Routing Modes 12 5 Controlling Machines via the Ethernet using the FC-10ETH 14 5.1 Controlling a Machine via a Computer 14

  • Kramer FC-10ETH, 2 FC-10ETH - Introduction 1.1 Terminology Used in this User Manual Term Definition 802.3 The standard specification for ETHERNET that is maintained by the Institute of Electrical and Electronics Engineers (IEEE). Dynamic Host Configuration Protocol (DHCP) Allows the network administrator to distribute IP addresses from a central point and automatically send a new IP address when an Ethernet point is plugged into a different network location. Gateway A network position serving as an entry to another network. On the Internet, a node or stopping poi

  • Kramer FC-10ETH, FC-10ETH – Technical Specifications 21 7 Technical Specifications ETHERNET INTERFACE: 10/100 BaseT Ethernet SERIAL INTERFACES: 2 RS-232 connectors, signals: RX, TX, RTS, CTS, Ground on 9−pin D−sub ports 1 RS-485 on a detachable terminal block connector NETWORK PROTOCOLS: ICMP, ARP (ping), TCP, UDP POWER SOURCE: 12 VDC, <80mA DIMENSIONS: 12cm x 7.5cm x 2.5cm (4.7” x 2.95” x 0.98”), W, D, H WEIGHT: 0.3kg. (0.25lbs) approx. ACCESSORIES: Power supply, mounting bracket OPTIONS: RK−3T 19" rack adapter Specifications are subject to change without notice Go to our Web site at Uhttp://www.kramerelectronics.comU to access the list of resolutio

  • FC-10ETH – Configuring the FC-10ETH Ethernet Controller 11 # Feature Function 1 Menu bar File Exit: closes the Configuration Manager application Action Search Board: seeks the FC-10ETH devices that connect to the PC via the ETHERNET port, and displays them and their corresponding settings Config: adjusts the FC-10ETH according to the displayed data Set MAC For facto

  • Kramer FC-10ETH, FC-10ETH – Overview 5 • Operates like an actual hardware port, that is, a logical COM that behaves like a standard hardware COM but in reality transparently reroutes the data using the TCP/IP network to the FC-10ETH interface via a Virtual null- modem connection, which you can emulate over the Ethernet or Internet • Can be created in any quantity on your PC and does not occupy an actual serial port 3.1 Defining the FC-10ETH Ethernet Controller Front Panel Figure 1: FC-10ETH Ethernet Controller Figure 2: Underside of the FC-10ETH Ethernet Controller

  • Kramer FC-10ETH, 14 FC-10ETH - Controlling Machines via the Ethernet using the FC-10ETH 5 Controlling Machines via the Ethernet using the FC-10ETH You can use your FC-10ETH to control a Kramer or non-Kramer RS-232/RS-485 machine: • From computers that connect to a LAN, as well as via an Internet connection (see Section 5.1 • Via a controller, as well as via an Internet connection (see ) Section 5.2 5.1 Controlling a Machine via a Computer ). To control a Kramer machine via five computers, as illustrated in the example in Figure 7, do the following: 1. Connect the 12V DC power adapter to the

  • Kramer FC-10ETH, FC-10ETH – Flash Memory Upgrade 19 6 Flash Memory Upgrade The FC-10ETH firmware is located in FLASH memory, which lets you upgrade to the latest Kramer firmware version in minutes! The process involves: • Downloading the upgrade package from the Internet • Connecting the PC to the RS-232 port (COM 1) • Upgrading the firmware 6.1 Downloading from the Internet You can download the up-to-date file from the Internet (file names are liable to change from time to time). To do so: 1. Go to our Web site at Uhttp://www.Kramerelectronics.comU and download the file: fc1

  • Kramer FC-10ETH, 20 FC-10ETH - Flash Memory Upgrade 6.3 Upgrading Firmware Follow these steps to upgrade the firmware: 1. Double click the KFR-Programmer desktop icon. The KFR-Programmer window appears (see Figure 10). Figure 10: The KFR-Programmer Window 2. Select the required COM Port to which the FC-10ETH is connected on your PC. 3. Press the File button to select the .s19 firmware file included in the package. 4. Press the Send button to download the file. The Send button lights red. 5. Wait until downloading is completed and the red Send button turns off. im Vertrieb von CAMBOARD Electr

  • KRAMER ELECTRONICS LTD. USER MANUAL MODEL: FC-10ETH Ethernet Controller P/N: 2900-000086 Rev 2 im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 Fax 07131 911203 [email protected]

  • Kramer FC-10ETH, FC-10ETH – Introduction 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1,000-plus different models now appear in 11 groups that are clearly defined by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5: Range Extender

More Instructions:

DOWNLOAD

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Nav TV SIRAUD Instructions nav-tv/siraud-LQ6.pdf 13 May 2023 4
2 BT STRATUS 1500 Operation & user’s manual bt/stratus-1500-D71.pdf 26 Mar 2023 2
3 Byron Home Easy HE-307 Installation instructions byron/home-easy-he-307-31U.pdf 17 Jun 2023 2 0.71 Mb
4 GE Security NX-592E Installation instructions manual ge-security/nx-592e-8R7.pdf 20 Nov 2022 20 0.37 Mb
5 Sound Storm SD712B Operation & user’s manual sound-storm/sd712b-CM6.pdf 18 Feb 2023 20
6 MSI 661FM2-V ILSR Operation & user’s manual msi/661fm2-v-ilsr-ZU7.pdf 02 Sep 2023 94

Similar Resources:

  • Helios

    KWL 45 BEU

    (52 pages)
    BedienelementControllerCommande à distanceKWL 45 BEUmit LED-Anzeigewith LED displayavec affichage LED Helios VentilatorenMONTAGE- UND BETRIEBSVORSCHRIFTINSTALLATION AND OPERATING INSTRUCTIONSNOTICE DE MONTAGE ET D’UTILISATION DE EN FR …
  • Hornbach

    Activalve S468

    (2 pages)
    RUBINETTERIE UTENSILERIE BONOMI SRL Via Padana Superiore, 27/29 Fraz. Ciliverghe - 25080 Mazzano (BS) – Italy MEETING STANDARDS IS OUR STANDARD Phone + 39 030 212441 Fax + 39 030 2629498 [email protected] www.rubvalves.com A circa +8°C chiusura automatica Activalve®. Activalve® può essere riaperto (operazione 4), quando la temperatura torna a condi …
  • Argo-Hytos

    EL6

    (4 pages)
    EL6Subject to change · EL6_9150_1en_02/2016www.argo-hytos.comPage 1 Digital Control Electronics Unit - Plug-in VersionTechnical Features › Digital electronics for open-loop control of a single proportional valve solenoid - plug-in version › Independent adjustments (including ramp up and ramp down) › Large, easy-to-use adjustments, readout on a 3-digit …
  • Daikin

    UATYP-AY1(B)

    (48 pages)
    18EnglishOperating ManualHandset WiredDeutschBedienungsanleitungVerdrahtetes HandgerätFrançaisMode D’emploiCombiné CâbléNederlandsBedieningsaanwijzingBedraad HandapparaatEspañolManual De InstruccionesAuricular AlámbricoItalianoManuale Di FunzionamentoRicevitore CablatoΕλληνικάΕγχειρίδιο ΟδηγιώνΑσύρµατη Χειροσυ …
  • Toshiba

    OIS40R

    (2 pages)
    April 2003 OIS40R Remote Operator Interface Station For Toshiba T-Series PLCs The OIS40R is the same OIS (Operator Interface Station) as the OIS40 except that the PLC communication port is selectable, RS232 or RS485. As a result, its location is not limited to the 2 m maximum distance from the PLC like the OIS4 …
  • Wet Sounds

    RF-RGB-MC V2

    (2 pages)
    RF RGB Music Controller Owner’s ManualWET SOUNDS INC.www.wetsounds.com877-938-7757 10621 S Sam Houston Pkwy W • Suite 100Houston, Texas 77071 USA© 2021 Wet Sounds, Inc. All Rights Reserved. WET SOUNDS and associated logos where applicable are registered trademarks of Wet Sounds Corporation in the United States and/or other countries. All other trademark …

Comments, Questions and Opinions: