IDS IDS805 User Giude
|
IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 17 IDS805 USER MANUAL 8.2 Panic Alarm [P] (Hold down the key until the keypad buzzer sounds) ! If the [P] key is pressed until the keypad beeps (approximately 1 second) a PANIC ALARM condition will be activated. ! A PANIC ALARM can also be activated by any FIXED PANIC or REMOTE PANIC buttons
IDS IDS805, 20 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL 5. Zones that have registered a tamper condition will have flashing indicators. 6. The memory status will be displayed for five seconds. 7. The zone tamper memory will only be erased if the [#] key is pressed while the memory is being displayed. 11. User Codes The IDS805 Alarm Panel has 15 programmable user codes. Code 1 :Master User Code Code 2 - 13 :General User Codes Code 14 : Maids Code Code 15 :Duress Code 11.1 Entering New and Changing Existing User Codes. [ !! !! !] + [MASTER USER CODE] + [ !! !! !] + [CODE NUMBER] + [ !! !! !]
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 11 IDS805 USER MANUAL 5.3 Stay Arming Procedure This allows the user to arm the perimeter zones while disabling the interior zones so that it is possible to remain on the premises. If zones are likely to be violated accidentally, they should be programmed as BUZZ zones (refer to page 22). The panel can be programmed with two different STAY PROFILES to be used as required. Following is an example of where this may be used. Assume a property has perimeter sensors to secu
IDS IDS805, 16 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL ! If the entry period is too short, have your installer change the entry delay period. ! If four incorrect user codes are entered consecutively while either arming or disarming the system, the keypad will be non- responsive for 30 seconds. Your monitoring company will also be notified on a keypad tamper. NOTE: If the ARMED indicator is flashing upon entry, there has been a violation. The intruder may still be inside! Call for assistance. NOTE: If a strob
IDS IDS805, 26 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL will also create a READY condition. Does the installer need to reset the system? Hold down the [7] key until the keypad buzzer sounds. If the zone 8 LED is illuminated contact your alarm installer immediately. It will not be possible to arm the system until the installer mode has been entered by entering the installer code. Does the siren sound before you exit? The exit delay may be too short - ask your installer to adjust the exit delay. OR
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 29 IDS805 USER MANUAL S Siren ..........................................................................8, 13, 16, 17, 26 Stay Arm - see “Arm” Stay Arm & Go - see “Arm” Stay Mode .................................................................................. 7, 11 Stay Profile ............................................................................2, 11, 12 Strobe ............................................................................................. 16 T Tamper .............................
IDS IDS805, 2 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL Summary of Operation mrasid/mrA ]#[ + ]EDOCRESU[ mrAyawAkciuQ nwoddloH ]1[ dnoces1rof mrAyatSkciuQ nwoddloH ]5[ dnoces1rof oG&mrAyatSkciuQ nwoddloH ]6[ dnoces1rof cinaP nwoddloH ]P[ dnoces1rof eriF nwoddloH ]F[ dnoces1rof ycnegremElacideM nwoddloH ]M[ dnoces1rof yromeMmralA nwoddloH ]0[ dnoces1rof eliforPyatSegnahC ]EDOM[ + ]9[ + ]REBMUNELIFORP[ + [!! ! !!] enozassapyB [!! ! !!] + ]REBMUNENOZ[ enozemihcmargorP nwoddloH ]2[ [+dnoces1rof ]REBMUNENOZ + [!! ! !!] enozyatsmargorP nwoddloH ]3[ [+
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 25 IDS805 USER MANUAL 15.1.1Viewing Trouble Conditions [7] (Hold down the key until the keypad buzzer sounds) If the POWER LED is flashing (or if so programmed, the keypad is beeping) hold down the [7] key for two seconds. The ARMED, AWAY and READY indicators will start flashing to show that the keypad is in the TROUBLE viewing mode. Refer to the table below to find the significance of each illuminated zone LED. The system will automatically exit the TROUBLE mode after ten seconds. To clear the trouble condition press [#] within 5 seconds of viewing. To simp
IDS IDS805, 24 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL 14.1 To Program the Chime Zones [2] + [ZONE NUMBER] + [ !! !! !] + [#] 1. Hold down the [2] key until the keypad buzzer sounds. 2. The AWAY indicator will flash to show that the panel is In the chime zone programming mode. 3. To program a zone as a chime zone, press the key corresponding to that zone followed by the [ !! !! !] key. The zone indicator will illuminate. 4. Program any other zones you wish to select as chime zones as per step 3. 5. Press the [#] key to exit the chime programming mode. 14.2 To Cancel the Chime Zones [2] + [ZONE NUMBER] + [ !! !! !] + [#] 1. Hold down the [2] key unti
IDS IDS805, 22 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL 4. Press the [#] key to exit the stay zone programming mode. 12.2 To Cancel the Stay Zones [3] + [ZONE NUMBER] + [ !! !! !]+ [#] If an area programmed as a STAY zone will no longer be violated during STAY arming, then the STAY status of such a zone should be cancelled. This will allow the system to protect that area during a stay arm cycle. 1. Ensure that the READY indicator is illuminated. 2. Hold down the [3] key until the keypad buzzer sounds. The AWAY indicator will flash to show that the panel is in
IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 27 IDS805 USER MANUAL Index A Alarm Memory .............................................................. 2, 5, 7, 18, 19 Arm ......................................................................... 2, 5, 8, 10, 14, 25 Away.................................................................................... 10, 12 Qui
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 7 IDS805 USER MANUAL 2. Understanding the Keypad Indicators Refer to the illustration on inside front cover of manual. 1. ARMED Indicator (Red) detanimullIdemrAmetsyS dehsiugnitxEdemrasiDmetsyS gnihsalFyromeMronoitidnoCmralA 2. AWAY Indicator (Red) detanimullIedoMyawAnidemrAmetsyS dehsiugnitxEedoMyatS/demrasiDmetsyS 3. POWER Indicator (Red) detanimullItneserpsirewoPsniaM gnihsalFnoitidnoCelbuorT 4. READY Indicator (Green) detanimullIdemraebotydaersimetsyS 5. ZONE Indicators (Yellow) detanimullIdessapybenoZ dehsiugnitxEraelcenoZ gnihsalFdetaloivenoZ
IDS IDS805, 18 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL mitted to the monitoring company to inform them that you have been forced to disarm the control panel by an intruder. ! It is advisable to choose a code that can be easily remembered by all family (or staff) members. 9.0 Emergency Evacuation Plan An emergency evacuation plan should be established in case of a fire: ! Draw up a floor plan of your premises showing windows, doors, stairs and rooftops that can be used for escape. ! Indicate a suitable escape r
IDS IDS805, 4 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL 8. Emergency Situations ..................................................16 8.1 Fire Alarm .......................................................................16 8.2 Panic Alarm ....................................................................17 8.3 Medical Alarm .................................................................17 8.4 Duress Code ..................................................................17 9.0 Emergency Evacuation Plan .......................................18 10. System
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 5 IDS805 USER MANUAL Glossary Alarm This is the history of the most recent violations that Memory occurred the last time the system was armed. Arm To set the system into the ARMED mode. In this mode, violating a zone will activate an alarm condition. If the system is programmed accordingly, will cause a reporting code to be sent to the monitoring company. Bypass To deactivate a zone. When the panel is ARMED, violation of a bypassed zone will be ignored. Disarm To deactivate the system. Fire, medical and panic functio
IDS IDS805, 28 IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 IDS805 USER MANUAL F Fire ................................................................................. 2, 5, 6, 8, 16 Follower Zone - see “Zone” Forced Arming ............................................................................ 8, 14 I Installer Code ............................................................................ 25, 26 Installer Reset ....................................................................
IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 21 IDS805 USER MANUAL 11.3 Maids Code The maids code (user 14) may be used to limit access to the premises. The maids code will only disarm the system if the same code was used for arming. If armed with a code other than a maids code, the system will view an attempt to disarm with the maids code as an invali
IDS IDS805, IDS805 USER MANUAL NO. 700-266-01A ISSUED NOV 2003 VER 1.00 19 IDS805 USER MANUAL 5. The alarm memory will be erased the next time the system is armed. 10.2 Zone Bypassed Memory The Zone Bypassed Memory displays any zones which were bypassed during the most recent arming cycle. To Display Zone Bypassed Memory: [0] then [1] 1. Hold down [0] until the keypad buzzer sounds. 2. The READY indicator will extinguish and the keypad buzzer will sound briefly. 3. Flashing zone indicators show which zones were violated during the last armed cycle. 4. To view any bypassed zones, press the [1] key once. 5. Zones that have have been bypassed will have flashing indicators. 6. The memory status wi
DOWNLOAD |
McIntosh WK-3 Keypad Owner's manual
WK-3 |
IDS 816 Keypad Installer manual
816 |
Videofied XMA Keypad Installation datasheet
XMA |
IDS IDS805 Keypad Quick start manual
IDS805 |
IDS X Series Keypad Operation & user’s manual
X Series |
IDS 805 Keypad Installer manual
805 |
IDS X64 Keypad Operation & user’s manual
X64 |
IDS X64 Keypad Installer manual
X64 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Philips | M870 | Instruction manual | philips/m870-7L5.pdf | 07 Dec 2022 | 36 | 1.73 Mb |
2 | Audiovox | Thera | Operation & user’s manual | audiovox/thera-5L8.pdf | 07 Oct 2022 | 154 | 2.34 Mb |
3 | Haier | HWM35-AS | Operation & user’s manual | haier/hwm35-as-135.pdf | 17 Dec 2022 | 18 | 1.8 Mb |
4 | Generac Power Systems | 0043736, 0046265 | Owner's manual | generac-power-systems/0043736-0046265-8G6.pdf | 06 Jul 2023 | 64 | 4.68 Mb |
5 | Fujitsu | PRIMERGY RX200 S8 | System configurator and order-information manual | fujitsu/primergy-rx200-s8-E22.pdf | 23 Aug 2023 | 28 | 0.59 Mb |
6 | Onkyo | TX-SV424 | Instruction manual | onkyo/tx-sv424-8YQ.pdf | 21 Mar 2023 | 24 |
Honeywell
ADEMCO 6152 / 6152V Keypads – Installation and Setup GuideAddressable Fixed English & Voice Fixed English Keypads for use with Honeywell Control Panels = READY to Arm= NOT READY to Arm= System ARMED= System NOT ARMEDArming Keys6152V: Message Indicators6152-6152V-KEYPAD-LBLD-07-19-13_1= Recording Message= No message= Message RecordedProgrammable Fun …
ADEMCO 6152(4 pages) |
Comelit
ITMANUALE TECNICOENTECHNICAL MANUALFRMANUEL TECHNIQUERUТЕХНИЧЕXСКОМУ РУКОВОДСТВУNLTECHNISCHE HANDLEIDINGTRTEKNIK KILAVUZUDETECHNISCHES HANDBUCHPLINSTRUKCJA TECHNICZNAESMANUAL TÉCNICOPTMANUAL TÉCNICOPassion.Technology.Design.Modulo tastiera numericaNumber keypad moduleModule clavier numériqueArt. UT9279MNumeriek toetsenbordmoduleNu …
UT9279M(40 pages) |
Follett
Order parts online: www.follettice.com 00170704R01801 Church Lane • Easton, PA 18040, USAToll free (877) 612-5086 • +1 (610) 252-7301www.follettice.comInstallation InstructionsKeypad Lock Retrot Kit for Follett REF Undercounter Refrigerator P/N 00170688Materials supplied Reference #Keypad assembly (housing and mounting base) 1Keypad housing base 2 …
00170688(8 pages) |
DediProg
DDDeeedddiiiPPPrrroooggg TTTeeeccchhhnnnooolllooogggyyy CCCooo... LLLtttddd wwwwwwwww...dddeeedddiiippprrroooggg...cccooommm …
DP-KPD-01(9 pages) |
DSC
IMPORTANT: This equipment shall be used in an environment that provides the pollution degree max. 2 in NON-HAZARDOUS locations ONLY.The WT4989 is a five-button two-way wire-less key with an LCD icon display and abuilt-in buzzer. The LCD provides displayicons that come on to show the system sta-tus when the Status Request button ispressed. In addition, the b …
WT4989(2 pages) |
urmet domus
DS1051-029A Mod. 1051 GUIDA RAPIDA QUICK GUIDE GUIDE RAPIDE SCHNELLANLEITUNG Tastiera remota a LED Led remote keypad Clavier déporté avec led Led-ferntastatur 1051/025
…
1051/025(12 pages) |
ZyXEL Communications Switch ES-2048PDF Guide (@71C73U), ZyXEL Communications ES-2048 Switch (Thu 01.2024) ES-2048, 311 |
Remington Trimmer NE-1Use and care manual for Remington NE-1 Trimmer NE-1, 9 |
Craftsman Lawn Mower 917.374112Lawn Mower PDF Owner's manual 917.374112, 52 |
Samsung Flat Panel TV PL63A750T1FSamsung PL63A750T1F User Manual (Doc Type: Flat Panel TV Quick start manual) PL63A750T1F, 5 |
Wharfedale Pro Home Theater System MS-100 HCP andUser Guide: Wharfedale Pro MS-100 HCP and (QUWBLP, Upd.20th Aug 2023) MS-100 HCP and, 12 |
Blodgett Kettle KPS-20EBlodgett Product Guide: KPS-20E PDF Installation operation & maintenance - QD91X7 KPS-20E, 9 |
Priefert Farm Equipment 04Priefert 04 Manual (Doc Type: Farm Equipment Owner's/operator's manual) 04, 12 |
Genius Software LMPROSoftware PDF Hardware manual LMPRO, 7 |
Peavey Processor AddVerb IIIAddVerb III (Processor ePDF User Guide, #G23SJV) AddVerb III, 54 |
Lava Cell Phone iris 355Lava Product User Guide: iris 355 PDF Operation & user’s manual - 715845 iris 355, 38 |
Toro Snow Blower 38535Toro Product Manual: 38535 PDF Operator's manual - QG52Q8 38535, 16 |
Abest PBX WPBX-9000-2LWPBX-9000-2L Operation & user’s manual - 7SPY5V WPBX-9000-2L, 31 |