Abocom WAP5502 Operation & User’s Manual

Text of Abocom WAP5502 User Guide:

• Abocom WAP5502, Chapter 2: Operation Modes 7 Access Point Mode When acting as an Access Point (AP), this device connects all the stations (PC/notebook with wireless network adapter) to a wireless network. Client Mode If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface.

• Abocom WAP5502, Chapter 4: Web Configuration 41 Firewall Port Filtering Enable Port Filtering Check to enable Port Filtering function. Port Range Enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current Port Forwarding information. De

• Abocom WAP5502, Chapter 5: PC Configuration 66 Accessing AOL To access AOL (America On Line) through the Wireless Router, the AOL for Windows software must be configured to use TCP/IP network access, rather than a dial-up connection. The configuration process is as follows: 　 1. Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or later. This procedure will not work with earlier versions. 　 2. Click the Setup button. 　3. Select Create Location, and change the location name from "New Locality"

• Appendix B: About Wireless LANs 71 Appendix B: About Wireless LANs BSS/ESS BSS A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a Basic Service Set (BSS). Using the same SSID is essential. Devices with different SSIDs are unable to communicate with each other. ESS A group of Wireless Stations, and multiple Access Poin

• Abocom WAP5502, Chapter 3: Installation 12 4. After connected successfully, the following screen will show up. Simply enter the username “admin” without password to login(case-sensitive). After login successfully, please click the Setup Wizard item that provides a primary configuration of this device. You may enter each screen to change the default settings step by step.

• Abocom WAP5502, Chapter 5: PC Configuration 59 Checking TCP/IP Settings - Windows 2000 1. Select Control Panel - Network and Dial-up Connection. 2. Right - click the Local Area Connection icon and select Properties. You should see a screen like the following: 3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct, as described below. Using DHCP • To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using th

• Abocom WAP5502, Chapter 4: Web Configuration 48 Address Type Select IP or MAC address type. Local IP address MAC address Depend on the address type that selected, user can enter the IP address or MAC address of client to set up the bandwidth of the transmission. Mode Select Guaranteed minimum bandwidth or Restricted maximum bandwidth modes. Uplink Bandwidth (Kbps) Enter the Uplink Bandwidth (Kbps) in the column. Downlink Bandwidth (Kbps) Enter the Downlink Bandwidth (Kbps) in the column. Comment Enter the note for the setting. Route Setup Enable Dynamic Route Dynamic routing performs the same function as static routing e

• Abocom WAP5502, Chapter 4: Web Configuration 54 Upgrade Firmware Select File Click the Browse button to find and open the firmware file (the browser will display to correct file path.) Upload Click the Upload button to perform. Reset Click Reset button to restore to default values. Save /Reload Settings Save Settings to File Click the Save button to save the current settings file in the PC. Load Settings form File Click the Browse button to find and open the previous saved file (the browser will display to correct file path.) Then,

• Abocom WAP5502, Chapter 4: Web Configuration 56 Bandwidth Mgmt Enable Bandwidth Management Check the box to enable this function. If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet / online game can have two-way connections. You can select automatic or manual uplink speed. Automatic Uplink/Download Speed Check the box to enable the automatic uplink/ download speed function. Manual Uplink/Download Speed You can manually enter the

• Abocom WAP5502, Chapter 4: Web Configuration 52 Denial of Service Enable DoS Prevention DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests, using so much bandwidth and so many resources that Internet access becomes unavailable. The Wireless Router incorporates protection against DoS attacks. This screen allows you to configure DoS protection. Check the box to enable the DoS settings.

• Abocom WAP5502, Chapter 4: Web Configuration 44 Port Forwarding Enable Port Forwarding Check to enable Port Forwarding function. IP Address Enter the IP address in the field. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Cli

• Abocom WAP5502, Chapter 4: Web Configuration 17 Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. Chapter 4: Web Configuration After login successfully, please click the Setup Wizard item that provides a primary configuration of this device. You may enter each screen to change the default settings step by step. Setup Wizard The setup wizard will guide you to configure access point for first time. Please follow the setup wizard step by step.

• 2 Table of Content Chapter 1: Introduction 1 Features 1 Hardware Connection 1 LED Indicators 2 Chapter 2: About the Operation Modes 3 AP Mode 3 GW Mode 3 Client Mode (Infrastructure) 4 Chapter 3: Configuration 5 Login 5 Common Connection Types 6 Configuration via Web 7 Operation Mode 7 Status 23 System Data 23 TCP/IP 24 Other 25 Chapter 4

• Abocom WAP5502, Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to ra

• Abocom WAP5502, Chapter 3: Installation 16 Common Connection Types Common Connection Types Cable Modems Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. Usually, none. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. Some ISP's may also require you to use a particular Hostname, Domain name, or MAC (physical) address. DSL Modems Type Details ISP Data required Dynami

• Abocom WAP5502, 2 CHAPTER 4: WEB CONFIGURATION...............................................................17 Setup Wizard.............................................................................................................................17 Wireless.......................................................................................................................................21 TCP/IP Settings........................................................................................................................35 Firewall....................................................................................

• Abocom WAP5502, Chapter 4: Web Configuration 43 MAC Filtering Enable MAC Filtering Check to enable MAC filtering function. MAC Address Enter the client MAC address in the field. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current MAC filter information. Delete Selected Click Delete Selected button to delete

• Chapter 3: Installation 11 Router Mode Connect via wireless… Step 1. Power on the wireless router first, connect the Wireless Router with a power to an outlet. Step 2. Then, connect the computer with the wireless router via wireless LAN interface. Step 3. After make a connection and set up(please refer to TCP/IP Settings> WAN Interface Setup) successfully, connect the ADSL o

• Abocom WAP5502, Appendix A: Troubleshooting 68 Appendix A: Troubleshooting Overview This chapter covers some common problems that may be encountered while using the Wireless Router and some possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the Wireless Router to configure it. Solution 1: Check the following: • Check the Wireless Router is properly installed, LAN connections are OK, and it is powered ON. • Ensure that your PC and the Wireless Router are on

• Abocom WAP5502, Chapter 4: Web Configuration 45 URL Filtering Enable URL Filtering Check to enable URL filtering function. URL Address Enter the URL address in the field. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current URL address filter information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all

• Chapter 4: Web Configuration 28 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS. To use WDS function: 1. The APs m

• Abocom WAP5502, Chapter 5: PC Configuration 65 For Windows 2000 1. Select Start menu - Settings - Control Panel - Internet Options. 2. Select the Connection tab, and click the Setup button. 3. Select "I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)" and click Next. 4. Select "I connect through a local area network (LAN)" and click Next. 5. Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked. 6. Check the "No" option when prompted "Do you want to set up an Internet mail account now?" 7. Click Finish to close the Internet C

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• NETGEAR DGN3500 - Wireless-N Gigabit Router (2 pages) Resource CDInternetFilter Splitter Filter/splitter (varies by country)N300 Wireless Gigabit ADSL2+ Modem RouterDGN3500Installation GuidePackage ContentsPower adapterTelephone cable1234Ethernet cableResource CDLaptop or desktopcomputer4-Step Cable Connection:Modem routerPhoneADSLPhoneLineADSLPhoneLineTip: Use an ADSL filter for everytelephone on the same phon …

• Allnet ALL0276 (86 pages) Multi-Function 802.11g Wireless Router 802.11g/802.11b Wireless Access Point Broadband Internet Access 4-Port Switching Hub User's Guide …

• Buffalo AirStation WLI2-TX1-G54 (2 pages) WLI2-TX1-G54www.buffalotech.com54 Mbps Wireless Ethernet Converter – WLI2-TX1-G54The Buffalo AirStation Wireless 54 Mbps Ethernet Converter is an extremelyversatile Wireless client adapter. Any device with an available Ethernet portcan be made wireless in minutes with AirStation One-Touch Secure System(AOSS™). Connect Wirelessly to Gaming consoles, Deskt …

• D-Link DWR-925 (16 pages) This document will guide you through the basic installation process for your new D-Link 4G LTE VPN Router.DWR-925 Quick Installation Guide4G LTE VPN 路由器Quick Installation Guide …

• Sony ALT-SA32PC (2 pages) Check the package contents1 Hook up the Wireless Speakers1. Insert a wireless transceiver into the back of each Wireless Speaker.STANDBY mark facing upInsert the wireless transceiver by pushing firmly until you cannot see it from the side.Insert securely until you hear a click.2. Set the S-AIR ID on the back of both Wireless Speakers to “A.”STANDBYTh …

• MikroTik RouterBOARD 750 (2 pages) RouterBOARD 750Quick Setup Guide and Warranty InformationFirst use1. Connect your WAN cable to port 1, and LAN computers to ports 2-52. Set LAN computer IP configuration to automatic (DHCP)3. RB750 Default IP address from LAN is 192.168.88.1 or http://routerPoweringThe board accepts powering from the power jack or from the first ethernet port (Passive PoE):� …

Comments, Questions and Opinions: