mabe Kraken Service Manual

Text of mabe Kraken User Guide:

• mabe Kraken, Ingeniería de Servicio - 23 - Remove three ¼ in. hex head screws securing the valve to the top cover and pull the valve up. Hold valve over the basket and disconnect the supply hoses from the valve. Quad Valve and the four rubber seals are together in the same part number

• mabe Kraken, Ingeniería de Servicio - 31 - Impeller To remove the impeller, pop the center cap off with a small flat screwdriver to access the 7/16 th in. hex bolt. The splined coupler is part of the impeller and agitators. Note.- Impeller bolt should be replaced any time it is removed for service and torqued to 100 in.lbs. If it is necessary, use a couple of nose pliers in order to disassemble the impeller.

• mabe Kraken, Ingeniería de Servicio - 70 - Fault Codes Fault Code (Hex) Name Description Repair Action 18 Drain Pump Clearing algorith m failed. While draining the pressure sensor value for water level did not indicate the washer was empty before the Max Continuous Drain ON time was reached.  This fault is set and will be seen with fault 16 when Drain Pump Clearing Algorithm failed to remove the blockage and the rest of water in tub.  Check the drain pump for blockage.  Check installation instructions for proper standpipe height.  Check pressure tube for pinches where it goes through top cover

• mabe Kraken, Ingeniería de Servicio - 25 - Dispenser Removal The dispenser hold detergent and fabric softener and delivers it at precise times for the cycle selected. Water is added to the dispenser from the water valve to fill and flush the cups. After the valve turns off the remaining water in the cup siphons out. Video Link When bleach is added to the bleach cup it is funneled through to the tub cover and into the tub. Remove the backsplash assembly, water valve and top cover. Remove the dispenser tray from the dispenser body. Remove four ¼ in. hex head screws from the top cover securing the dispenser body to the top cover

• Ingeniería de Servicio - 1 - Service Manual June-2016 Top Load Washer Kraken 27” HTW200BMKWW GTW460BMKWW MTW200BMKWW GTW485BMKWS GTW220BMKWW GTW680BMKWS GTW330BMKWW GTW680BMKDG GTW465BMKWS

• mabe Kraken, Ingeniería de Servicio - 20 - Two Coil Water Valve Turn water supply off to valve. Hoses do not need to be disconnected at this time. Remove two Phillips head screws that go through the thermistor mounting bracket into the body of the valve. Remove thermistor by pulling up on lip of thermistor. Ensure o-ring is removed with thermistor.

• Ingeniería de Servicio - 62 - Service Mode Tests Knob Index / Test number (Displayed on SSD, 7-segment display, if present) (Without SSD will be displayed in binary format. (See Binary Chart) Test Name Description of test If tests call for numbers to be shown it will: (Display on SSD, 7-segment display, if present) (Without SSD will be displayed in binary forma

• mabe Kraken, Ingeniería de Servicio - 15 - Lid Lock Striker Video Link The lid lock striker slides into the lid lock/switch assembly. When a cycle is started the lock assembly engages with the striker preventing the lid from opening during the cycle. The latch has spring tension on it to keep it engaged with the switch/lock assembly

• mabe Kraken, Ingeniería de Servicio - 44 - Drive Belt The drive belt has five ribs and can be removed easily turning the pulley to walk the belt off. To reinstall the belt, put it on the motor pulley first. Stretch the belt around the transmission pulley as far as it can go. Then rotate the pulley until the belt is in place. Be sure all the ribs of the belt.

• mabe Kraken, Ingeniería de Servicio - 42 - Drain And Recirculation Pump Recirculation pump The GTW680 model has a recirculation pump located at the front of the bottom of the tub. It mounts to the tub the same as the drain pump. Video Link Drain Pump The drain pump is located on the right side of the bottom of the tub. It is mounted directly to the tub secured by three (3) 3/8 th in. hex head bolts. Video Link Both pumps are 120 VAC. The approximate resistanc

• mabe Kraken, Ingeniería de Servicio - 43 - Drain And Recirculation Pump Once the bolts are removed, the pump can be pulled from the tub. Have something to catch excess water. The seal is integrated to the pump as one Part Number.

• Ingeniería de Servicio - 49 - Platform Transmission Assembly The platform transmission assembly is one complete part with the exception of two harness connector brackets and one motor splash guard. These will need to be transferred to the new platform assembly when replacing the platform transmission assembly. The platform assembly is secured to th

• mabe Kraken, Ingeniería de Servicio - 40 - Harness Removal/Replacement The cabinet needs to be removed to replace the harness assembly. Once the cabinet is removed there are two ¼ in. hex head screws that secure the harness to the side of the tub that need to be removed. There is one ¼ in. hex head screw on the bottom.

• mabe Kraken, Ingeniería de Servicio - 27 - Top Cover Removal Remove the lid assembly and control panel assembly. . Disengage the power cord from the top cover by pulling up on the front of the power cord grommet. Slide the power cord grommet forward

• mabe Kraken, Ingeniería de Servicio - 56 - Display Test and Fault Chart Fault/Test # displayed on 7-segment display When entered into service mode Service Mode Test 0 All LEDs on 1 Fault Codes 2 Personality ID 3 UI Software Version (Critical) 4 UI Software Version (Non-Critical) 5 XML Version (Non-critical) 6 Hot Water Valve 7 Cold Water Valve 8 Fabric Softener Dispenser 9 Spray Rinse Valve 10 Preasure Sensor 11 Recirculate Pump 12 Drain Pump 13 Lid Switch 14 Spin 15 Agitate 16 Clear all F Codes 17 Change Person

• Ingeniería de Servicio - 35 - Basket Removal Remove the 1-5/16 th in. hub nut by turning the nut clock-wise to loosen (reverse threads). A new hub nut should be used when reinstalling the basket assembly. Torque to 100 +/- 10 ft.lbs. Remove the hub washer Right position Wrong position Be c

• mabe Kraken, Ingeniería de Servicio - 59 - Service Mode Tests Knob Index / Test number (Displayed on SSD, 7-segment display, if present) (Without SSD will be displayed in binary format. (See Binary Chart) Test Name Description of test If tests call for numbers to be shown it will: (Display on SSD, 7-segment display, if present) (Without SSD will be displayed in binary format. (See Binary Chart) Turning the cycle knob will index to the next or prior test. 5 XML Version (Non-Critical) Example: v01.23 High end UI 1 st press – “01” on SSD 2 nd

• Ingeniería de Servicio - 58 - Service Mode Tests Knob Index / Test number (Displayed on SSD, 7-segment display, if present) (Without SSD will be displayed in binary format. (See Binary Chart) Test Name Description of test If tests call for numbers to be shown it will: (Display on SSD, 7-segment display, if present) (Without SSD will be displayed in binary format. (S

• mabe Kraken, Ingeniería de Servicio - 2 - IMPORTANT SAFETY NOTICE IMPORTANT SAFETY NOTICE The information in this presentation is intended for use by individuals possessing adequate backgrounds of electrical, electronic, & mechanical experience. Any attempt to repair a major appliance may result in personal injury & property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. WARNING To avoid personal injury, disconnect power before servicing this product. If electrical power is required for di

• mabe Kraken, Ingeniería de Servicio - 21 - Tilt back of valve up and slide out of top cover. Once valve is out and held over the basket, disconnect hoses. Valve, funnel and Gasket are one part.

• mabe Kraken, Ingeniería de Servicio - 8 - Water Levels Approximate Minimum Water Levels  Impeller – 7 Gallons or 3 in. depth from the bottom of the basket.  Agitator – 9 Gallons or 3-3/4 in. depth from the bottom of the basket. Test are completed with an empty basket. Approximate Maximum Water Levels  Impeller – 26 Gallons or 13-1/2 in. depth from the bottom of the basket. Press and hold for 3 seconds “Deep Fill” to achieve.  Impeller “Bulky” setting water level i

• Ingeniería de Servicio - 7 - Serial Number and Mini Manual Location Serial Number The Serial Number breaks down and explains what the letters and numbers mean in its structure: Example of Serial Number: LG312345C  The first two characters of the serial number identify the month and year of manufacture: LG = June, 2016 A = JAN A = 2013

Related Products and Documents (Washer):

Comparable Devices:

Similar Resources:

• Panasonic NA-V11FX2 (62 pages) 1 Order No: PAPVW2012001E 1 SERVICE MANUAL 2 Fully Automatic Washing Machine 3 (Household Use) 4 Model NA-V11FX2 5 Model NA-V11FG2 6 Model NA-V10FX2 7 Model NA-V10FG2 8 Model NA-V90FX2 9 Model NA-V10FX1 10 Model NA-V90FB1 11 Model NA-V95FX2 12 Model NA-V85FX2 13 Model …

• RCA WRW3505K (24 pages) ——–Atitator23Appliance Registration2Care and Cleaning23Controls Setting Guide 6,7CycleSettings 5Detergents, Other Ad&tives 11-15Energy-SavingTips 5Hard Water14Limestone Deposits12Loading the Washer4,10Model and Serial Numbers 2C)PeratinEInsti~ions4,5Pre-Treating79,15Problem Solver18-22Repair Service23Safetv Instructions3,4Soak Setting5,8SortinE4,9S …

• GE GBVH6260 (24 pages) ge.com175D1807P476 49-90207 05-05 JRWashersSafety Instructions . . . . . . . . . . . . 2, 3Operating InstructionsControl Panels . . . . . . . . . . . . . . . . 4–5Control Settings . . . . . . . . . . . . . . . . . .6Fabric Care Labels . . . . . . . . . . . . . . .11Features . . . . . . . . . . . . . . . . . . . . . .7, 8Loading and Using the Washer . …

• Samsung SW52ASP (12 pages) Owner’s InstructionsRegister your product atwww.samsung.com/global/registerCODE NO. : DC68-01488K-ENPlease read this manual before using and note how to use in the proper manner.Please be careful of keeping the manual.Otherwise, it should be bought separately.The User’s Manual is for common use.Make use of the User’s Manual depending upon your washing …

• Miele WT 2780 wpm (8 pages) Quick Start GuideWasher-dryerWT 2780 WPMThese short instructions are not a substitutefor the Operating instructions supplied with the appliance.Please read the Operating instructions supplied withyour Washer-dryer before using it for the first time andtake note of the Warning and Safety instructions as wellas the full descriptions on how to use your machine. …

• Daewoo DW-6510 (9 pages) PARTS IDENTIFICATIONACCESSORYROTATIONLIMITROTATIONLIMIT• TUB• OVERFLOW FILTER• LINT FILTER• WASHER LID• DRAIN STRAINER• PULSATOR• BASE• SPINDRYER LID• INNER LID• SPINDRYER DRUM• GROUND WIRE(OPTION)• POWER CORDControl panelSPIN TIMER0MIN123WASH SPIN45WASH TIMERVALVE SELECTOR0MIN3691215(OFF)(WASH• RINSE)1Wash TimerUse to select the de …

Comments, Questions and Opinions: