Manualios.com

Geeetech Delta Rostock mini G2S Pro Manual 

Geeetech Delta Rostock mini G2S Pro Manual Online:

3.5, 724 votes
Geeetech Delta Rostock mini G2S Pro User Manual
Geeetech Delta Rostock mini G2S Pro User Guide
Geeetech Delta Rostock mini G2S Pro Online Manual

Text of Geeetech Delta Rostock mini G2S Pro User Guide:

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 1 - Copyright Declaration The copyright of this manual belongs to the Shenzhen GETECH CO., LTD. (hereinafter referred to as the "Geeetech"), and all rights reserved. No part of this specification should be reproduced or extracted in any forms or means without the prior written consent of Geeetech by any company and individuals. Technical Support If you are interested in the technology of 3 D printing, flight control and U-home, welcome to Geeetech, we have series of made-up products, main boards, modules and a variety of peripherals for you. Or if you are looking for relevant information or technical support, please l

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 2 - SAFETY INSTRUCTIONS Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided detailed instructions to help you assemble it easily, please download at geeetech.com. However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read the entire manual to enable you to make an informed decision. Building and oper

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 3 - special care and attention should be made when handling these parts of the printer during operation. We wouldn’t recommend leaving your printer running unattended, or at least until you are confident to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer. INTRODUCTION: This Rostock mini G2s pro is a upgraded delta 3D printer redesigned by Geeetech. Compared to its predecessor, this G2s pro has two major merits, it looks cooler and it works better. The

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 4 - printing, and with this new metal leveling device, the calibration will be more accurate. PACKAGE LIST: This list includes all the parts required to assemble your Delta Rostock mini G2s pro 3D Printer. After you received your package, please check if all the parts listed are included. Also make sure all the components are in good condition and not damaged during shipping. If anything is missing please contact with our customer service straight away, provide us the NO. , Name, and Qty. Mechanical parts No Name Specifications Qty Pic 1 Smooth Rod D10 L500mm 6 2 Spool D8 L235mm 1

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 5 - 3 Rod-end bearing holder D6.5 23mm 12 4 Diagonal Rod With rod-end bearing 6 5 M3 Washers M3 101 6 M4 Washers M4 15 7 M5 Washers M5 8 8 M8 Washers M8 12 9 Nut M2.5 6 10 Nut M3 8

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 6 - 10A nut M5 24 11 Lock nut M4 3 12 Wing nut M3 6 13 Square nut M3 27 14 Hex Counter- sunk-hea d screw M3x30 mm 3 15 Round head screw with pad M3 x 8 mm 12 16 Screw M2.5x8mm 2 17 Screw M2.5x16mm 8 18 Screw M3x8mm 12 19 Screw M3x12mm 32

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 7 - 20 Screw M3x16mm 32 21 Screw M3x20mm 2 22 Screw M3x25mm 8 23 Screw M3x40mm 3 24 Screw M4x8mm 12 24A Screw M4x12mm 8 25 Screw M4x16mm 2 26 Screw M4x25mm 3 27 Screw M5x16 12 27A Screw M5x20 12 28 Spring 4.0x 20(for heat bed) 3 29 Spring 3.5*30 ( for endstop trigger) 4 30 locking ring M8 With Jimmy bolt 2

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 8 - 31 Ball Bearing MR84zz 6 32 Driven wheel 3 33 Driven wheel holder Sheet metal part 3 34 Pulley 20 tooth 3 35 Linear Bearing PCS10UU 6 36 Timing Belts 2GT L=1200mm 3

  • GEEETECH - 9 - 37 Spacer With Aircraft type end 8 38 Nylon ties 20 39 Feeding pipe PTFE L=600mm 2 40 Spiral Coil 3 meters 1 41 Sticker 2 42 Heat sink 9*10*5mm 5 43 Probe Φ3 L60mm 1

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 10 - Electronic parts 44 End stop 2-pin Blue--1pcs, Red----2pcs Black-1pcs 4 45 Fan 40x40x10mm 1 46 Extension wire 3Pin Male-3Pin Female 2 47 Fan 30x30x10mm (with 1200mm extend wire) 1 48 Knob For LCD control 1

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 11 - 49 LCD 2004 LCD2004+ cable 1 50 Control board kit GT2560+ 5 A4988 1 set 51 USB cord A-BA 1 52 Thermometr y wire 2pin(pasted on heatbed) 1 53 Heating Wire 30cm(soldere d on heatbed) 2

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 13 - 58 Power Supply Unit AC Input: 115V/2.2A 230V/1.1A DC Output: 12V/0-20A 1 59 3D printer Power Cable With plug 1 60 Power Cable Connect board to PSU 1 Acrylic parts A1 Top plate RK-01 1 A2 Base plate RK-02 1

  • GEEETECH - 14 - A3 Motor holder RK-03 3 A4 Motor holder support RK-04 6 A5 Drive wheel mount RK-05 3 A6 Endstop mount RK-06 3 A7 Fan mount RK-07 1 A8 LCD frame RK-08 1 A9 LCD support RK-09 2

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 15 - A10 Spool holder Side panel RK-10 1 A11 Spool holder Side panel RK-11 1 A12 Carriage mount RK-12 3 metal parts M1 Spider 1 M2 Fan mount 1 M3 Probe Lock ring with M3*3 screw 1

  • Geeetech Delta Rostock mini G2S Pro, GEEETECH - 17 - F2 File 1 F3 Screw- driver 1 GENERAL CARE AND MAINTENANCE As with all the electronic equipment, it is important to keep your printer clean to extend its life. Regularly remove dust and debris with a microfiber cloth or compressed air. Dredge the tube and the nozzle after use every time to ensure fluent performance.  Don’t leave the heaters on the printer turned on for a long periods of time when not used.  Don’t leave your printer in shady and moist places, which may exacerbate the problems associated with erosion.  The three axes of the Delta Rostock mini G2s pro are lubricated with grease for smooth operation and can last

  • GEEETECH - 18 - the brick is hanging, pulling, or putting any unnecessary stress in the electrical wires and components. SUPPROT Thanks for choosing Geeetech, we strive to provide a satisfied and pleasant shopping experience for you, but we do understand there may be some questions you may encounter in using our product. If so, you can contact us directly or post on our fo

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 AEG Electrolux 68031K-MN Operation & user’s manual aeg-electrolux/68031k-mn-VB1.pdf 26 Oct 2023 96 0.68 Mb
2 Electro-Voice Sx300a Product information electro-voice/sx300a-9D4.pdf 07 Feb 2024 8
3 Epson PowerLite Home Cinema 8700 UB Brochure & specs epson/powerlite-home-cinema-8700-ub-752.pdf 22 Feb 2024 4 1.79 Mb
4 Fisher-Price SERGEANT SIRENTM G6534 Instruction sheet fisher-price/sergeant-sirentm-g6534-333.pdf 04 Dec 2022 6 0.43 Mb
5 HP D2847W Operation & user’s manual hp/d2847w-L1X.pdf 17 Jul 2022 22
6 Nostalgia Electrics CSD-250 Instruction manual nostalgia-electrics/csd-250-441.pdf 15 Feb 2024 3

Similar Resources:

  • Carbide 3D

    HDZ 3.3

    (15 pages)
    [email protected] docs.carbide3d.com 01/24/2020 Version 3.3.1 1 HDZ 3.3 Assembly Guide Intro Thank you for purchasing the HDZ. We know you’ll enjoy your purchase! If you run into any issues during assembly, please contact us at [email protected]. Prior to fitting the HDZ please ensure you can rotate the ball screw by hand and move the carriage …
  • Tinkerine Studio

    Ditto Pro

    (4 pages)
    Make sure the printer is located near an accessible power outlet.Use a box cutter to trim along the taped edges and peel back the outer box aps.The DittoPro™ 3D Printer can be too heavy to lift out of the box by yourself. Ask for help to prevent injury or damages to the printer.Open shipping box and remove the compartment lid.1Remove foam bracket and ta …
  • RepRap

    Prusa i3

    (69 pages)
    Prusa i3 – Build ManualTable of ContentsForward............................................................................................................................................................................... 41. Y-AXIS Frame..................................................................................................................... …
  • Dremel

    3D20 Idea Builder

    (2 pages)
    FilamentGuidePRESSLIFTIMPORTANT: IMPORTANT : IMPORTANTE:Read Before Using Lire avant usage Leer antes de usarFor English Version Version française Versión en españolSee page 2 Voir page 37 Ver la página 73Operating/Safety InstructionsConsignes de sécurité/d’utilisationInstrucciones de funcionamiento y seguridad1-844-4DRML3D (1-844-437-6533) www.dre …
  • Flashforge

    Finder

    (10 pages)
    finderCaution1. HYPERTHERMAL! AVOID TOUCHING THE HEATING NOZZLE IN OPERATION. 2. DANGERS OF BEING ENTANGLED AND WOUNDED. DO NOT WEAR GLOVES OR OTHER SOURCES OF ENTANGLEMENT IN OPERATION.Quick Start GuideRTHIS GUIDE IS ONLY APPLICABLE TO FLASHFORGE FINDER 3D PRINTERSZ05-EN-A02The User Guide is in the USB stick.User Guide …
  • Dremel

    3D20 Idea Builder

    (8 pages)
    3D20 Quick Start GuideWARNINGWARNINGREAD ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.ENGLISH …

Comments, Questions and Opinions: