I-Bus IBC2602 Operation & User’s Manual

Text of I-Bus IBC2602 User Guide:

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-3 IBC2602 User's Guide PCI Device Mapping The IBC2602 includes the PCI device mapping listed in Table 2-3 below. Bus Number Device Number Fcn Number Vendor ID Device ID Description 00 00 00 8086 7190 Intel 82443BX North Bridge 00 01 00 8086 7191 Intel 82443BX AGP Bridge 00 07 00 8086 7110 Intel 82371EB South Bridge (PIIX4E) 00 07 01 8086 7111 Intel 82371EB IDE 00 07 02 8086 7112 Intel 82371EB USB 00 07 03 8086 7113 Intel 82371EB ACPI 00 0C 00 8086 1209 Intel 82559ER Ethernet 00 0D 00 8086 1209 Intel 82559ER Ethernet 00 0F 00 1011 0046 Intel 21554 PCI to PCI Bridge 01 09 00 1026 0C30 C&T V

• I-Bus IBC2602, Table of Contents 3 IBC2602 User's Guide Chapter 3. BIOS Setup Options Entering Setup Screen 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard Disk Setup 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CompactFlash Setup 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDROM Setup 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saving to CMOS 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 4. Specifications Compatibility 4-1. . . . . . . . . . . . .

• I-Bus IBC2602, Appendix 2 - FCC Information A2-1 IBC2602 User's Guide This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class A" digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reas

• I-Bus IBC2602, Chapter 1 - Introduction 1-1 IBC2602 User's Guide Important Safety Instructions LITHIUM BATTERY REPLACEMENT CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Ersatz rur durch denselben oder einen vom Hersteller empfohlenengleichwertigen Typ. Entsorgung gerbrauchter Batterien noch Angaben Herstellers. Product Description The IBC2602 is a 6U CompactPCI  , single slot, peripheral m

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-8 IBC2602 User's Guide CompactFlash Drive Configuration The IBC2602 contains a site for an industry standard CompactFlash disk. The interface is mapped to the primary IDE interface. Use jumper W9 for Master/Slave status configuration. Position jumper W9 to the 1-2 position to make the drive a master and to the 2-3 position to make the drive a slave. See the BIOS Setup Options section for information on configuring the BIOS for a CompactFlash drive. Flat Panel Interface An opt

• Chapter 3 - BIOS Setup Options 3-2 IBC2602 User's Guide CD-ROM Setup No special setup is required in the BIOS to support a CD-ROM drive. The CD-ROM driver will examine the IDE channels, determine if a CD-ROM is present, and map a drive letter for the CD-ROM. Saving to CMOS After changing the various setup parameters select the WRITE TO CMOS AND EXIT menu to write the changes to the no

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-21 IBC2602 User's Guide PMC Connectors (J17/J20) The two PMC connectors are fully compliant with the IEEE 1386 specification for a 32-bit implementation. The IBC2602 uses a Molex 71439-0164 connector on the baseboard to support standard 10mm PMC spacing. Universal or 5V PMC modules are supported (VIO is connected to 5V). Pin Signal Pin Signal 1 TCK 2 No Connect 3 GND 4 INTA# 5 INTB# 6 INTC# 7 BUSMODE1# 8 5V 9 INTD# 10 Reserved 11 GND 12 Reserved 13 CLK 14 GND 15 GND 16 GNT#

• I-Bus IBC2602, Chapter 1 - Introduction 1-2 IBC2602 User's Guide Standard Features S 6U (160mm x 233.5mm) x 4HP CompactPCI  form factor (single slot) S Supports Mobile Pentium  III Processors up to 700MHz S Supports Celeron  processors up to 533MHz S 256Kbytes Integrated L2 Cache on Pentium  III Processors S Up to 512Mbtyes of SDRAM S CompactFlash socket S Dual 10/100 Base-TX Ethernet Channels - Rear I/O supported S AGP SVGA Video Support up to 1600x1200x64K S Flat Panel Support for TFT/STN Panels S 32 bit PCI Mezzanine Card (PMC) Expansion S 512 Kbytes of Flash for S

• I-Bus IBC2602, Chapter 1 - Introduction 1-6 IBC2602 User's Guide The serial ports support standard RS-232 signal levels at baud rates up to 115 Kbaud. The keyboard and mouse connectors are industry standard 6-pin MiniDIN and are compatible with standard desktop PS/2 keyboards and mice. Hardware Monitor A National Semiconductor LM87 Hardware Monitor provides CPU temperature, supply voltage, and fan speed monitoring. Watchdog Timer A watchdog timer optionally monitors system operation to be sure that application software is executing as designed. The watchdog timer generates hardware reset if the application software fails to strobe the watchdog timer with a minimum time interval. Sect

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-20 IBC2602 User's Guide CompactFlash Socket (J16) This socket is the industry standard pinout and accepts standard true IDE mode Type 1 and 2 CompactFlash cards. Pin Signal Pin Signal 1 GND 26 N/C 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS0# 32 CS1# 8 GND 33 VS1# 9 GND 34 IORD# 10 GND 35 IOWR# 11 GND 36 WE# 12 GND 37 INTRQ 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 N/C 16 GND 41 RESET# 17 GND 42 IORDY# 18 A2 43 N/C 19 A1 44 VCC 20 A0 45 N/C 21 D0 46 N/C 22 D1 47 D8 23 D2 48 D9 24 N/C 49 D10 25 N/C 50 GND Table 2-20:

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-19 IBC2602 User's Guide Processor Fan Connectors (J14) These headers are industry standard 3-pin 0.1" keyed Molex Pin Number Signal 1 GND 2 VCC 3 TACH (Optional) Table 2-18: J14 Pin Assignment IDE/Floppy Mezzanine Connector (J15) The IDE/Floppy mezzanine connector uses a male 2x25 header with 2mm spacing. Several optional mezzanine boards are available from I-Bus/Phoenix which attach to this connector. These mezzanines contain various configurations

• Chapter 2 - Configuration and Installation 2-15 IBC2602 User's Guide CompactPCI Connector (J5) - Backplane I/O This connector contains the primary IDE channel, floppy, COM1, COM2, LPT, USB, mouse and keyboard signals Pin A B C D E F 22 PRST# GND N/C VCC SPKR GND 21 KBDAT KBCLK VCC MSDAT MSCLK GND 20 VCC N/C N/C GND N/C GND 19 STB# GND VCC N/C N/C GND 18 AFD# USB1+ USB1- GND

• Chapter 2 - Configuration and Installation 2-1 IBC2602 User's Guide Memory and I/O Mapping There are several memory and I/O devices local to the IBC2602. There are also expansion sites for adding memory and I/O resources. The address maps for these devices are shown in Table 2-1 below. Memory Space Memory Address (hex) Description 768M – 4G 30000000 –

• I-Bus IBC2602, IBC2601 Us er’ s Gui de 4 Dear Customer, Thank you for purchasing an I -Bus Corporation pro duct. We hope that this product exceeds your expectations. It is our desire to provide you with accurate, up -to-date information about the product(s) you have purchased. We welcome your comments and suggestions about our manuals. You may email those comments and suggestions to [email protected]. Please be sure to include your name, the name of your company, the product you purchased, and the manual number/revision (i.e. 00-00000-00 Rev. *). This number is located on the title page. At I -Bus Corp., we value our customer

• Chapter 2 - Configuration and Installation 2-5 IBC2602 User's Guide Parallel I/O The IBC2602 includes parallel I/O bits coming from the 82371EB PIIX4E South Bridge for controlling and monitoring various functions. Access these bits at I/O location x1030h through x1032h for the inputs and x1035h through x1037h for the outputs. Table 2–5 details the operation for each

• I-Bus IBC2602, Chapter 1 - Introduction 1-4 IBC2602 User's Guide BIOS Flash The system BIOS is contained in a single 512 Kbyte Flash loaded into a 32-pin PLCC socket. The Flash write strobe includes a series zero-ohm resistor that can permanently disable the write operation. IDE and CompactFlash The IBC2602 supports a primary and a secondary IDE drive, routed to a mezzanine board connector and CompactFlash socket. The primary interface includes mapping to the Mezzanine connector and the CompactFlash socket. Additionally, both the primary and secondary channels are available through the rear I/O (J4/J5). The default CMOS setting configures the CompactFlash drive as a primary.

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-7 IBC2602 User's Guide Serial Console Redirection The IBC2602 supports console redirection through the COM1 serial port. During initialization, the BIOS checks to see if the RIN and DTR pins of the COM1 serial port are tied together and if so will redirect the console to the serial port. A standard ASCII terminal program such as HyperTerminal (Win 95) may then be used to communicate with the IBC2602. Console redirection provides text only support. Use a null modem adapter or cross over cable to communicate with another DTE device (i.e. desktop computer or terminal). The IBC2602 serial connector is configured as DTE. The

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-14 IBC2602 User's Guide CompactPCI Connector (J4) - Backplane I/O (Not Loaded) This connector contains the secondary IDE channel and fan monitoring signals. This connector is generally not loaded to allow support for H110 backplanes, which use the J4 connector Pin A B C D E F 25 N/C N/C N/C N/C VCC GND 24 CS1S# CS3S# GND GND N/C GND 23 IO16# DA1 GND DA0 DA2 GND 22 GND IORDY N/C DDAK1# MIRQ0 GND 21 DDRQ1 GND DIOW# GND DIOR# GND 20 DD14 DD0 DD15 GND N/C GND 19 DD3 DD12 DD2 DD13 DD1 GND 18 DD9 DD5 DD10 DD4 DD11 GND 17 PWRGD GND DD7 DD8 DD6 GND 16 N/C N/C N/C N/C GND GND 15 GND VCC VCC N/C N/C GND 14 KEY AREA 13 KEY AREA 12 11 N/C GND N/C

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-17 IBC2602 User's Guide USB Connector (J9) The frontplate USB connector is an industry standard 4-pin USB connector. Pin Number Signal 1 Fused VCC 2 USB- 3 USB+ 4 GND Table 2-13: J9 Pin Assignments Keyboard Connector (J10) The frontplate keyboard connector is an industry standard 6-pin MiniDIN female connector. The PS/2 Mouse signals have also been mapped to this connector to allow use of a splitter cable for keyboard/mouse support Pin Number Signal 1 Keybo

• Chapter 2 - Configuration and Installation 2-16 IBC2602 User's Guide Front Panel Ethernet (J6/J7) The front panel Ethernet connectors use industry standard 8-pin RJ45's. Pin Number Signal 1 TX+ 2 TX- 3 RX+ 4 Termination 5 Termination 6 RX- 7 Termination 8 Termination Table 2-11: J6/J7 Pin Assignments Video Connector (J8) The frontplate video connecto

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-11 IBC2602 User's Guide CompactPCI Connector (J1) This connector contains the 32-bit PCI bus signals. Pin A B C D E F 25 5V REQ64# ENUM 3.3V 5V GND 24 AD[1] 5V V(I/O) AD[0] ACK64# GND 23 3.3V AD[4] AD[3] 5V AD[2] GND 22 AD[7] GND 3.3V AD[6] AD[5] GND 21 3.3V AD[9] AD[8] M66EN C/BE0# GND 20 AD[12] GND V(I/O) AD[11] AD[10] GND 19 3.3V AD[15] AD[14] GND AD[13] GND 18 SERR# GND 3.3V PAR C/BE1# GND 17 3.3V N/C N/C GND PERR# GND 16 DEVSEL# GND V(I/O) STOP# LOCK# GND 15 3.3V FRAME# IRDY# BSEL TRDY# GND 14 13 KEY AREA 12

• I-Bus IBC2602, Chapter 2 - Configuration and Installation 2-13 IBC2602 User's Guide CompactPCI Connector (J3) - Backplane I/O This connector contains the IRDA and Ethernet channel 0 and 1 signals. Pin A B C D E F 19 N/C N/C N/C N/C N/C GND 18 N/C N/C N/C IRRX IRTX GND 17 N/C N/C N/C N/C N/C GND 16 N/C N/C N/C N/C N/C GND 15 N/C N/C N/C N/C N/C GND 14 N/C N/C N/C GND N/C GND 13 N/C VCC N/C N/C N/C GND 12 N/C N/C N/C VCC N/C GND 11 N/C GND N/C N/C N/C GND 10 GND N/C N/C N/C N/C GND 9 E1TX+ E1TX– E1RX+ E1RX– GND GND 8 GND VCC VCC N/C N/C GND 7

Related Products and Documents (PCI Card):

Comparable Devices:

Similar Resources:

• B&B Electronics 3PCIOU1 (4 pages) Documentation Number: 3PCI-MIport-4004qsg %%(OHFWURQLFV0IJ&R,QF±'D\WRQ5G32%R[2WWDZD,/3K)D[±ZZZEEHOHFFRP%%(OHFWURQLFV/WG±:HVWOL …

• OPTO 22 PCI-AC51 (52 pages) PCI-AC51 AND PCIE-AC51USER’S GUIDEForm 1459-131106—November 201343044 Business Park Drive • Temecula • CA 92590-3614Phone: 800-321-OPTO (6786) or 951-695-3000Fax: 800-832-OPTO (6786) or 951-695-2712www.opto22.comProduct Support Services800-TEK-OPTO (835-6786) or 951-695-3080Fax: 951-695-3017Email: [email protected]: support.opto22.com …

• DeLOCK 89111 (4 pages) KurzbeschreibungDie DeLock PCI Express Karte erweitert Ihren PC um zwei externe USB 2.0 und einen internen USB 2.0 Port, sowie um zwei externe FireWire B und einen internen FireWire B Port. Sie können an die Karte verschiedene USB und FireWire Geräte wie z.B. Digitalkameras, Camcorder, Drucker, Scanner, Tastaturen, Mäuse, Lautsprecher, …

• National Instruments 6711 (88 pages) DAQ Analog Output SeriesAnalog Output Series User ManualNI 6711/6713/DAQCard-6715, NI 6722/6723, and NI 6731/6733 DevicesAnalog Output Series User ManualJanuary 2017370735F-01 …

• SIIG JJ-P00112-S6 (12 pages) 1Parallel PCI 1PQuick Installation Guide04-0358CIntroducing the Parallel PCI 1PThe Parallel PCI 1P high-speed parallel card provides oneadditional parallel port to your system. Depending onthe model purchased, this board will fit into either Full orLow Profile chassis.Features and Benefits• Conforms to PCI v2.2 Plug and Play• Supports 32-/64-bit, …

• Moxa Technologies CP-102E (2 pages) — 1 — — 2 — — 3 — CP-102E/CP-102EL PCI Express Multiport Serial Board Quick Installation Guide First Edition, July 2008 1. Overview MOXA’s new PCI Express multiport serial boards, the CP-102E and CP-102EL, are designed for POS and ATM applications and for use by industrial automation system manufacturers and system integrators. The boar …

Comments, Questions and Opinions: