Cisco MX200 G2 Installation Manual

Text of Cisco MX200 G2 User Guide:

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 1 Manpower Two people working together are required to mount the system. Room setup Explore the Cisco Project Workplace website to find inspiration and guidelines when preparing your office or meeting room for video conferencing, http://www.cisco.com/go/projectworkplace Documentation Cisco Spark: Visit the Cisco Spark help site to find more information about Spark registered room systems, http://help.ciscospark.com Other services: Visit the Cisco web site to find user guides and compliance and safety information for the video system, htt

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 2 • Wall bracket • Monitor bracket • Bottom adapter • Screwdriver C D A B Monitor Accessories: • Microphone(s) • Cables • Screws for mounting the bottom adapter • Gloves Touch controller

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 3 1 Mount the monitor bracket Use gloves when handling the monitor. A B C Fasten the bracket with the four screws that you just removed. Unscrew these four screws. You will re-use them when fastening the bracket. Lay the monitor gently face down on a steady, soft surface. Take care not to subject the camera for any stress. 1 2

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 4 2 Mount the bottom adapter Remove the cable channel lid for now. You need it in step 4. 2 × M6x16 A C

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 5 3 Connect the cables For maintenance only Reset to factory settings Audio line output Always use the provided power cable. The wall socket outlet must be easily accessible after installation. Power switch Audio line input LAN 1 Video input 2 (e.g. PC) Video output 2 (e.g. 2 nd display) Power (100-240 VAC, 50/60 Hz) Touch controller 1 USB, for future use HDMI DVI-I Microphone 3 2 nd microphone 2, 3 C D 1 Use the cable that is labeled with for the Touch control

• Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 6 4 Snap on the cable channel lid Snap on the cable channel lid for strain relief.

• Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 7 5 Mount the monitor to the wall Due to the size and mass of this product, it is important that the wall-mounted system is safely installed according to these installation instructions. The wall and mounting hardware must be able to safely support the produ

• Cisco MX200 G2, Installing Cisco TelePresence MX200 G2 - Wall Mount 78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 8 EMC Class A declaration WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 声 明 此为 A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种 情况下，可能需要用户对其干扰采取切实可行的措施。 WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate

More Instructions:

	Cisco MX200 G2 Quick reference manual 09-04-2023 2	DOWNLOAD
	Cisco MX200 G2 Quick reference manual 08-06-2023 2	DOWNLOAD
	Cisco MX200 G2 Quick reference manual 06-02-2024 2	DOWNLOAD
	Cisco MX200 G2 Operation & user’s manual 31-08-2022 74	DOWNLOAD

Related Products and Documents (Projector Accessories):

Comparable Devices:

Similar Resources:

• InFocus SP-LAMP-090 (2 pages) Lamp Module Replacement Instructions: SP-LAMP-090 1. Turn off the power to the projector by pressing the Power button twice. 2. Disconnect the power cord. 3. Wait 60 minutes to allow the projector and lamp to cool thoroughly. 4. Loosen the captive screw on the lamp door. 5. Pull up and remove the lamp door. WARNING: Do n …

• Panasonic UB-5838C (136 pages) © Panasonic Communications 2009 Unauthorizedcopying and distribution is a violation of law.Order Number KM70906495CECategory Number H19Electronic BoardModel No. UB-5838CModel No. UB-5338C …

• Acer PD113P (35 pages) ... English1Table of ContentsTable of Contents .................................................................................................. 1Usage Notice ......................................................................................................... 2Precautions ................................................................................ …

• Elite ProAV CineGrey 5D (9 pages) Rev. 03072019JA 1 www.eliteproav.com Evanesce Tab-Tension CineGrey 5D® Recessed In-ceiling Ambient Light Rejecting Projector Screen Installation Guide The screen material included is our award winning CineGrey 5D® which is a front projection material, precisely formulated for environments with minimal control over room lighting. It was des …

• NEC VT695 (2 pages) 7N8P7261Printed in China©NEC Viewtechnology, Ltd. 2006Ver. 1 09/06 (T)1 Connect the supplied power cable. Schließen Sie das mitgelieferte Netzkabel an. Connecter le câble d'alimentation fourni. Collegate il cavo d´alimentazione in dotazione. Conecte el cable de alimentación suministrado. Anslut den medlevererade nätkabeln.2 Turn on the main p …

• CHIEF RSM A-D (16 pages) INSTALLATION INSTRUCTIONSInstructions d´installationIstruzioni di installazioneInstallationsanleitungInstrucciones de instalaciónInstallatie-instructiesInstruções de InstalaçãoRSM Elite Series Projector MountsRPA Elite Series Projector MountRPA Elite Series Projector MountRPA Elite Series Projector MountRPA Elite Series Projector MountRPA Elite Series …

Comments, Questions and Opinions: