Fujitsu Primergy RX300 S3 Operating Manual

Text of Fujitsu Primergy RX300 S3 User Guide:

• Fujitsu Primergy RX300 S3, 76 Operating manual RX300 S3 Hot-plug Power Supply Units Hot-plug Components 8.1.2 Adding a hot-plug Power Supply Unit Ê Insert the second power supply unit, lock it in the free location (see section “Replacing a Hot-plug Power Supply Unit”) and connect it to the line voltage (see section “Connecting the Server to the Line Voltage” on page 45). 8.1.3 Replacing a Hot-plug Power Supply Unit Figure 18: Unlocking and removing the power supply unit V CAUTION! Before replacing a non defective power supply unit in a non-redundant configuration (only one power supply unit present) the serve

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 29 Important Notes CE Certificate ● Use a grounding cable designed for this purpose to connect yourself to the system unit as you install components. ● Place all components on a static-safe base. I You will find a detailed description for handling ESD components in the relevant European or international standards (EN 61340-5-1, ANSI/ESD S20.20). Other important points: ● When cleaning the device, please observe the relevant notes in section “Cleaning the Server” on page 63. ● Keep this operating manual and all additional documentation (such as the technical m

• Fujitsu Primergy RX300 S3, 24 Operating manual RX300 S3 Safety Important Notes Before operating the device V CAUTION! ● During installation and before operating the device, observe the instructions on environmental conditions for your device (see section “Technical Data” on page 20). ● If the device is brought in from a cold environment, condensation may form both inside and on the outside of the machine. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. ● Transport the device only in the original packaging or

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 47 Hardware Installation Connecting and Disconnecting Cables 4.5 Instructions on Connecting and Disconnecting Cables V CAUTION! Be sure to read the documentation for the peripheral devices before connecting them. Do not connect or disconnect data cables during a thunderstorm. When removing a cable, always hold it by the plug. Never unplug a cable by pulling at the cable itself. Connect and disconnect the cables in the order described below. Connecting cables Ê Turn off all power and equipment switches. Ê Pull all

• Fujitsu Primergy RX300 S3, 52 Operating manual RX300 S3 Operating and Indicator Elements Preparation for Use and Operation Indicators on the optional USB hot-plug tape drive Figure 14: USB Hot-plug tape drive Hard disk drive indicators Figure 15: 3.5-inch HDD module: indicators 1 Clean indicator 2 Media indicator 3 Drive indicator Table 4: 1 2 3

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 21 2 Installation Steps: Overview In this chapter you will find an overview of the steps necessary to install your server system. Links guide you to sections where you can find more detailed information on the individual steps: Ê At first, please take notice of chapter “Important Notes” on page 23ff, Ê The server is accompanied by several loose items. Keep these items in a safe place. They are required for fitting additional add-on components. Ê Unpack the system, check the contents of the package for visible transport damage and check whether the delivery agr

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 13 Introduction Features USB interface The two USB interfaces on the front of the server supports activities carried out by the service technician. The maximum length of the external cable are three meters. Power supply In its basic configuration, the server has a hot-plug multi-range power supply unit that adjusts automatically to any power voltage in the range from 100 V - 240 V. An additional power supply unit can be installed optionally in order to ensure redundancy

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 81 Hot-plug Components Hot-plug Hard Disk Drives The hard disk drives that can be ordered for the PRIMERGY RX300 S3 are delivered as HDD modules, with the hard disk drives preinstalled on carriers. The hard disk drive may only be removed from the carrier by personnel with the appropriate technical training in compliance with the appropriate ESD guide- lines (see section “Modules with electrostatic-sensitive components” on page 28). Figure 21: 3.5-inch HDD module and dummy c

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 85 Hot-plug Components Hot-plug Hard Disk Drives Installing the 3.5-inch HDD module Figure 26: Installing the 3.5-inch HDD module Ê Unlock the HDD module as described in “Unlocking the 3.5-inch HDD module” on page 83. Ê Carefully push the HDD module into the empty slot (1) until it stops. Ê Push the handle completely in the direction of the arrow (2) until the locking mechanism (3) engages (4). 2 3 4 1

• 38 Operating manual RX300 S3 Installing/Removing the Server into/from the Rack Hardware Installation 4.2.1 Mounting into the PRIMECENTER/DataCenter Rack For mounting the server into the PRIMECENTER/DataCenter Rack the following parts are necessary: – support bracket – one left and one right telescopic rail (assembled) – M5-10 screws including plugwasher

• 56 Operating manual RX300 S3 Operating and Indicator Elements Preparation for Use and Operation Indicators on hot-plug PCI slots The indicators on these slots behave differently depending on whether (table 5) or not (table 6 on page 57) the operating system supports hot-plug functionality: Power indicator (6)/(green) Error indicator (5)/(orange) Status description does not light doe

• 100 Operating manual RX300 S3 Abbreviations LBA Logical Block Address LCD Liquid Crystal Display LUN Logical Unit Number LVD Low-Voltage Differential SCSI MMF Multi Mode Faser MRL Manually Retention Latch NMI Non Maskable Interrupt NVRAM Non Volatile Random Access Memory OS Operating System PCI Peripheral Component Interconnect PDA Prefailure Detection and Analysing POST

• Fujitsu Primergy RX300 S3, 36 Operating manual RX300 S3 Installing/Removing the Server into/from the Rack Hardware Installation 3rd-Party Rack Certain boundary conditions are to be fulfilled: – Installation dimensions (see the dimensions shown in figure 4 on page 37). – The operability of the safety mechanisms at the server e.g. stoppers or holding back systems must be guaranteed. – The form of the rack support uprights must ensure the frontal screwing on of the rails. – Frontally bolted telescopic rails. The rails are provided with a linear alignment possibility to ensure also an adjustment to different rack depths. – No support of the cable management (delivered with th

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 59 Preparation for Use and Operation Switching the Server ON and OFF Other ON/OFF options In addition to the ON/OFF button, the server can be switched ON and OFF in the following ways: – Specified switch-on time/switch-off time The server is switched ON or OFF at a time specified in the ServerView program. – Ring indicator The server is switched ON via an internal or external modem. – Wake On LAN (WOL) The server is switched on by a command via the LAN (Magic Package). – After power

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 49 5 Preparation for Use and Operation V CAUTION! Please note the safety instructions in chapter “Important Notes” on page 23. 5.1 Operating and Indicator Elements 5.1.1 The Front The operating and indicator elements on the front side are show in figure 13 on page 50. Operating elements ON/OFF button When the system is switched OFF, it can be switched ON again by pressing the ON/OFF button. When the system is operating, pressing the ON/OFF button will switch OFF the system. I The ON/OFF button does not

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 105 Index 3rd-Party Rack installing in 41 requirements 36 A accessible drives CD-ROM 12 DVD-ROM 12 floppy disk drive 12 tape drive 12 acclimatization time 80 ASR&R 14 availability 13 B BIOS security functions 65 BIOS update 16 blue screen (error) MRL sensor illegally activated 72 C cable management 40 cables connecting 47 disconnecting 47 CD-ROM drive indicator 50, 51 CE certification 18, 29 chipkill 13 cleaning monitor, mouse, server, keyboard 63 closing housing 95 components hardware/software 7 configuring server

• RX300 S3 Operating manual 99 Abbreviations FRU Field Replaceable Unit FSB Front Side Bus GAM Global Array Manager GUI Graphical User Interface HDD Hard Disk Drive HSC Hot-Swap Controller I²C Inter-Integrated Circuit I/O Input/Output ICM Intelligent Chassis Management ID Identification IDE Intergrated Drive Electronics IME Intergrated Mirroring Enhanced IRQ Interrupt Reques

• Fujitsu Primergy RX300 S3, 66 Operating manual RX300 S3 BIOS Setup Security Functions Property and Data Protection Preventing unauthorized writings of floppy disks To activate this protection, select the value Disabled for the Diskette Write field in the Security menu. Protecting BIOS from being overwritten To activate this protection, select the value Disabled for the Flash Write field in the Security menu. Protecting the server from being switched on by an external device To activate this protection select the value Disabled for the Remote Power On field in the Security menu. Protecting the server from b

• Fujitsu Primergy RX300 S3, Comments… Suggestions… Corrections… The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Fax forms for sending us your comments are included in the back of the manual. There you will also find the addresses of the relevant User Documentation Department. Certified documentation according to DIN EN ISO 9001:2000 To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regul

• Fujitsu Primergy RX300 S3, 14 Operating manual RX300 S3 Features Introduction appropriately in the BIOS; see BIOS Setup under “Related Publications” on page 103). The deactivated memory bank is no longer used and the faulty memory module can be replaced at the next opportunity. In order to be able to use the hot-spare memory function, all occupied memory banks must have an identical memory configuration. ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in the case of an error and automatically „hides“ the defective system components. The PDA (Prefailure Detection and Analyzing) technology from Fujitsu Siemens Computers analyzes and monitors all c

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 71 Troubleshooting and Tips Drives Are Reported as „Dead“ 7.10 Drives Are Reported as „Dead“ This error message may occur when the onboard SAS controller supports RAID functionality or the server has a PCI RAID controller: RAID controller configuration incorrect Ê Check and correct the settings for the drives with the RAID controller utility. Further information is provided in the manual on the RAID controller. 7.11 Added Drive Reported Defective RAID controller is not configured for this hard disk drive The drive was probably installed when the system was switched OFF. Ê Reconfigure the RAID controller for the drive with the corresp

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 75 8 Hot-plug Components This chapter describes how to handle hot plug components and/or how to modify your server hardware. The hot swap procedure (online replacement) increases the availability of the system operation and guarantees a high degree of data integrity and fail-safe performance. I Upgrades or replacements of permanently installed components are described in the Options Guide and/or in the Service Supplement and may only be performed by Service staff. V CAUTION! Please observe the safety information in chapter “Important Notes” on page 23. 8.1 Hot-plug Power Supply Units I A redundant

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 63 Preparation for Use and Operation Cleaning the Server 5.5 Cleaning the Server V CAUTION! Switch the server off and pull the power plug(s) out of the grounded-contact power socket. Do not clean any interior parts yourself; leave this job to a service technician. Do not use any cleaning agents that contain abrasives or may corrode plastic. Ensure that no liquid enters the system. Ensure that the ventilation areas of the server and the monitor are clear. Clean the keyboard and the mouse with a disinfecting cloth. Wipe the server and monitor casing with a dry cloth. If particul

• Fujitsu Primergy RX300 S3, RX300 S3 Operating manual 103 Related Publications PRIMERGY manuals are available as PDF file on the ServerBooks DVD. The ServerBooks DVD is part of the ServerView Suite delivered with each server system. The actual version of the necessary manuals can be downloaded free of charge from the Internet. The overview page showing the online documentation available in the Internet can be found via the URL: http://manuals.fujitsu-siemens.com (choose: industry standard servers). [1] Safety notes and other important information [2] Warranty [3] Ergonomics [4] Returning used devic

• Fujitsu Primergy RX300 S3, 106 Operating manual RX300 S3 Index display drifts 69 drive "dead" 71 drive defective 71 floppy disk cannot be read or written 70 incorrect PCI board installed 72 MRL sensor illegally activated 72 no mouse pointer 69 power failure during enable sequence 72 screen remains dark 68 screen shows flickering stripes 69 server switches off 68 system does not boot 70 wrong date 70 wrong time 70 Error Correcting Code 13 Error Detection Code 13 error message on screen 73 ESD (devices sensitive to electrostatic discharge) 28 ESD-sensitive devices 28 ext

More Instructions:

	Fujitsu Primergy RX300 S3 Options manual 02-02-2023 121	DOWNLOAD
	Fujitsu Primergy RX300 S3 Service supplement manual 18-07-2023 59	DOWNLOAD
	Fujitsu Primergy RX300 S3 Specifications 26-12-2022 2	DOWNLOAD
	Fujitsu Primergy RX300 S3 Options manual 01-06-2023 124	DOWNLOAD

Related Products and Documents (Server):

Comparable Devices:

Similar Resources:

• Enterasys ANG-3000 (18 pages) AVN-RMRN-R312 Page 1 of 18Release NotesRiverMaster™ Version 3.5IntroductionThis document provides up-to-date information on Version 3.5 of the RiverMaster management application. For complete information on RiverMaster, refer to the RiverMaster Administrator’s Guide. If there are discrepancies between the information in that document and these Release No …

• HP D7171A - NetServer - LPr (6 pages) Setting Up the HP Netserver LP 1000r (1.13 and 1.26 GHz)HP Netserver Installation Sheetn•šŒ†ˆ) ) ) )LP 1000r(1.13 and 1.26 GHz)The information contained in this document is subject to change without notice.Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantabilit …

• Hermstedt StingRay 3.0 (26 pages) Hermstedt StingRay 3.0 The Local Users Guide v 1.2 Publication Date - March 2011 Hermstedt StingRay The multi protocol File Transfer Server © Pro2col Limited and/or its Affiliates. All rights reserved. …

• NEC Express5800/R320g-E4 (82 pages) Chapter 1 Installing Operating System Chapter 2 Installing Bundled Software Chapter 3 Configuring the Separate Log Server Installation Guide (VMware) NEC Express Server Express5800 Series Express5800/R320g-E4 Express5800/R320g-M4 EXP320T, EXP320V 30.104.01-138.01July 2019© NEC Corporation 2019 …

• Huawei SVN2000 Series (10 pages) HUAWEI SVN2000/5000 V200R001C00 Quick Installation GuideSafety InformationIssue: 01Date: 2012-05-23zSVN2200 contains SVN2230 and SVN2260, SVN5500 contaThe Quick Installation Guide is applicable to the S SVN2230/2SVN5530/5530-C1/5530-C3/5560 (the SVN for short) as an exzThis document guides you through quick installation. For mordisk. zFor how to install the …

• Compaq 108164-003 - ProLiant - 800 (17 pages) INTEGRATION NOTE1................................................................................................................................................................ECG043/1097October, 1997Prepared ByNovell IntegrationBusiness Unit, CompaqComputer CorporationCONTENTSExecutive Summary ........ 3Introduction ................... 4PCNTNW.LANCustom St …

Comments, Questions and Opinions: