FScurtis Nx Series Operator's Manual

Text of FScurtis Nx Series User Guide:

• FScurtis Nx Series, CAP-837 2.7.5.2 "Inputs / Outputs" screen Overview Fig. 43: "Inputs ICommand - Touch" screen (Part 1/2) This menu is used to assign functions to the digital inputs and outputs and to the accessory modules. Fig. 44: "Inputs ICommand - Touch" screen (Part 2/2) Eight digital inputs and seven digital outputs are available on the ICommand however it is possible to change if required. Output 1 ICommand type. 4.6.6.4 " Heating / ventilation" screen Fig. 45: "Heating / ventilation" screen In the "Heating / ventilation" screen the heating or the ventilation can be sw

• FScurtis Nx Series, CAP-837 2.7.2 "Operating parameters" menu This menu contains the following parameters: Parameter Value setting/Initial setting/Remarks Automatic restart Automatic restart after power failure. Setting range: Yes/No Initial setting: No Remote On/Off Specifies the possibility to switch the system on or off remotely. If yes, switching on and off can be done via a digital input. If no, a programmed digital input will be ignored. Setting range: Yes/No Initial setting: No Remote Load / Idling Specifies the possibility to trigger an external load request via a digital input. If yes, switchin

• FScurtis Nx Series, CAP-837 1.3 General safety 1. Read and understan d all the instructions found in this manual before operating your compressor. 2. Disconnect the main power source before working on or performing any maintenance procedures on this unit. Use a lock out and tag out process. 3. Do not attempt to remove any parts, break any connection, loosen oil fill plug or drain plug unt unit has been shut down and air pressure has been relieved. 4. Do not operate the compressor in excess of its rated pressures and speeds indicated on the com pressor nameplate. 5. Do not remove guards, shields, or screens while the com

• FScurtis Nx Series, CAP-837 2.7.6 "Factory settings" menu Fig. 47: "Factory settings" screen Parameter Value setting/Initial setting/Remarks Start-up time Specifies the start Setting range: 3 Initial setting: depending on compressor type Off time Specifies the minimum run switch off of the compressor. This value is also used during restart delays after power failure. Setting range: 0 Initial setting: 120 s Run on time Specifies the run on time of the compressor in automatic o

• CAP-837 Warning message Remarks W033: Speed reduction The on "W034: "Speed reduction" programmed digital input was opened. Delay 1 s. W034: Dryer The on "W034: Dryer" progr opened.- no delay. W036: Condensate drain The on "W036: "Condensate drain" programmed tal input was closed. W037: Air filter The on "W0

• FScurtis Nx Series, CAP-837 2.7.10 "SD - Card" menu All functions with access to the SD The respective card must be inserted for usage. 2.7.10.1 Save parameters The Card without write protection. 2.7.10.2 Load parameters The parameter set of SD SD Start and stop data logging Fig. 57: "SD - Card" screen This function starts data logging on the SD without write protection. The following data is also written:  Time stamp  System state  Final temperature  Oil  Air quantity  State of all connected compressors (only on LLC) Fig.

• FScurtis Nx Series, CAP-837 2.4 Display structure Overview iCommand 13 Display structure Fig. 3: ICOMMAND - TOUCH basic display This illustration contains, for illustration purposes, a combination of symbols, which are not possible in a real system. The settings and operating parameters are shown in the display. Five buttons (Fig. 3/5–9) are located on the right- hand side of the basic display, which allows access to all important functions and information for the system. iCommand – Touch iCommand - Touch This illustration contains, for illustration purposes, a combination of symbols, which are not possible in a rea

• FScurtis Nx Series, CAP-837 2.5 Switching the compressor on/off Switching the compressor on Switching the compressor off 2.6 Access to the menu system 2.6.1 Code input Fig. 18: "Code input" screen iCommand 21 Switching the compressor on/off Switching the compressor on 1. Press . Switching the compressor off 1. Press . During the switch- off process, the compressor initially switches to "Off load" (motor running, however the compressor is not compressing any air; a flashing dot appears on the screen) for the duration of the off time. Only then does the compressor switch off (the motor stops).

• FScurtis Nx Series, CAP-837 Fault message Remarks E078: Line pressure high Network pressure too high. The pressure has exceeded the set upper limit. E079: System pressure conf. The system pressure switch digital input has not opened after 35 s in on E095: I/O-Module (Add.4) The accessory module on address 4 (Type MK200 8E4RA) does not respond. This monitoring is only a tive, if this module has E096: I/O-Module (Add.5) The accessory module on address 5 (Type MK200 8E4RA) does not respond. This monitoring is only a tive, if this module has been

• FScurtis Nx Series, CAP-837 17 18 19 20 21 22 iCommand 15 Motor runs display "Remote" display: Remote On/Off is activated "Restart" display: Automatic restart is activated Button "?" to open the symbol explanation State display If this symbol is shown, then the an inverter. Display "LLC mode activated" (display of the master controller) iCommand – Touch iCommand - Touch "Remote" display: Remote On/Off is activated "Restart" display: Automatic restart is activated

• CAP-837 Parameter Value setting/Initial setting/Remarks Max. no. of motor starts During activated switch cycles monitoring: motor starts per hour. Setting range: 1 – 60 /h Initial setting: depends on compressor type Lead lag control During operation with an external LLC (as LLC slave) Local pressure tole ance is ignored. However, with the LLC - OK functi

• CAP-837 2.7.4.6 "Diagrams" screen Fig. 35: "Diagrams" screen Settings for the illustration of the diagrams can be made in the "Diagrams" screen. Parameter Value setting/Initial setting/Remarks Storage interval Specifies the recording interval for the flow diagrams. Setting range: 1 – 60 s Initial setting: 6s X-Auto per

• FScurtis Nx Series, CAP-837 Fig. 12: "Temperature" screen Fig. 13: "Air quantity" screen Fig. 14: "Usage" screen Fig. 15 : "Maintenance interval" screen iCommand 19 In the "Temperature" screen the temperature of the system is graphically displayed. In the "Air quantity" screen the air quan tity is displayed in cubic feet per hour. In the "Usage" screen the amount of operating hours, on off-load hours and rea dy hours are graphically displayed. : "Maintenance interval" screen In the "Maintenan

• FScurtis Nx Series, CAP-837 2 I COMMAND - TOUCH 2.1 Overview of the ICOMMAND 2.2 Brief description iCommand 11 TOUCH Overview of the ICOMMAND - TOUCH No. Key/icon Description of function 1 Display Displays settings and operating parameters. 2 Serves to switch on the compre sor. 3 Serves to switch off the compre sor. During the start, the control displays for about three seconds come screen. The display changes automatically to the basic display. The control unit has a resistant color touch s

• FScurtis Nx Series, CAP-837 1 Safety ................................ ................................ 1.1 Symbols in these instructions 1.2 Proper use ................................ 1.3 General safety ................................ 1.4 Safety devices ................................ 1.4.1 Position of the safety devices 1.4.2 Description of the installed safety devices 1.5 Environmental protection ................................ 1.6 Instructions on the machine ................................ 2 ICOMMAND - TOUCH ................................ 2.1 Overview of the ICOMMA

• FScurtis Nx Series, CAP-837 2.6.2 Access to the menu system without a code Fig. 19: "Main menu" screen In the menus all changeable parameter can be selected via a button (see Fig. Fig. 20: "Control" screen (can not be changed) When accessing the menu system without a code only a value display is released. Instead of a button pears. The main menu includes the following submenus:  Control  Operating parameters  Maintenance counter  Timer  Display parameters  Configuration  Factory settings  Fault log  LLC  Diagnostics  SD iCommand 22 Access to the m

• FScurtis Nx Series, CAP-837 2.7.9.3 "Pressure times LLC" screen Fig. 55: "Pressure times LLC" screen 2.7.9.4 "Priority LLC" screen Fig. 56: "Priority LLC" screen iCommand 49 "Pressure times LLC" screen The pressure times of the LLC are defined in this menu (i crease/decrease). Th is only applies for the LLC master. Programming is done analogous to the "Pressure times compr." in section  Chapter 2.7.4.3 ‘ "Pressure times compr.&quo

More Instructions:

FScurtis Nx Series Service manual 16-01-2023 78

DOWNLOAD

Related Products and Documents (Air Compressor):

Comparable Devices:

Similar Resources:

• VIAIR 420C (8 pages) 420C AIR COMPRESSOR KITPART NO. 42042 460C AIR COMPRESSOR KITPART NO. 46043 IMPORTANT:It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL FOR FUTURE REFERENCEUSER MANUAL420C460C …

• Gude 410/10/50 230 V (48 pages) 410/10/50 230 V #50013 © Copyright Güde GmbH & Co. KG - Birkichstrasse 6 - 74549 Wolpertshausen - Germany Deutsch 6 Magyar 12 Čeština 17 Slovenčina 22 Nederlands 27 English 33 Français 38 Italiano 44 …

• Campbell Hausfeld DP4615 (8 pages) Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop.erty damage! Retain instructions for future reference.AirCompressorsDescripti …

• Campbell Hausfeld VS260000KB (24 pages) 24 SpManual de InstruccionesCompresores de Aire EstacionariosStationaryAir CompressorPlease read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/ …

• Graco ProCart 233449 Series A (30 pages) 309244Rev. MRév. MAusgabe MFirst choice whenquality counts.tTI0822INSTRUCTI ONS--PARTS LISTMANUEL D’INS TRUCTIONS -- LIS TE DE PIÈCE SBETRIE BSANLEI TUNGBEDIE NINGS INSTRUCTIE S -- ONDERDELE NLIJSTINSTRUCTIONSANLEITUNGINSTRUCTIESThis ma nua l cont a ins im por t a nt war nings a ndinformation. Ce manue l cont ie nt des m is es en gar de e tdes informa t …

• Wallmek HSC2018 (88 pages) Manual för hydraulisk äderkomprimator HSC2018Svenska sida 2-13, manual i originalUser manual for hydraulic spring compressor HSC2018English page 14-25Bedienungsanleitung für hydraulischen Federspanner HSC2018Deutsch Seite 26-37Mode d’emploi pour l’oul hydraulique de compression de ressort HSC2018Français page 50-61Bedieningshandleiding voor hyd …

Comments, Questions and Opinions: