Manualios.com

FrontRow JUNO Configuration Manual

FrontRow JUNO Manual Online:

4.9, 2164 votes
FrontRow JUNO User Manual
FrontRow JUNO User Guide
FrontRow JUNO Online Manual

Text of FrontRow JUNO User Guide:

  • FrontRow JUNO, 11 4. Intercom / PA Audio These settings are for use when installed with the Conductor IP-based Paging, Intercom and Bell system or with a 29V, 70V, or 100V analog paging system. Incoming Audio The PA volume is the volume of incoming audio from Conductor (pages, bells and intercom) and does not affect the volume of the local (in room) audio. PA Release is the amount of time it takes for the local (in room) audio to return to normal volume after an incoming audio stream from Conductor. Outgoing Audio (talk-back) Gain setting for the audio sent back to the front office from the in-room intercom microphone, i.e. the wall (CB75) or ceiling (CB85) uni

  • FrontRow JUNO, 24 Appendix B: Configuration File Settings Setting Saved in Configuration File About Custom Device Name Yes Password Required Yes Password Yes Intercom / PA Audio Incoming Audio Settings Yes Outgoing Audio Settings Yes Push to Talk Mode Yes Analog Page Override Settings Yes System Settings Master Volume No Microphone Volumes No Aux Input Volumes No OptiVoice No PrioriTeach No Command Channel No Speaker EQ Calibration No Equalizer No Microphone Button Mode Yes Beacon Brightness (Smart Receiver only) Yes Beacon / LCD System On Yes Backup PoE Power Yes Voice Command Yes Recording Yes Recor

  • 3 4. Gathering information You will save a lot of time by working with the school to: • Make a list of all rooms to be outfitted and the equipment to be controlled in each • Set aside IP addresses for each Juno Connect, and any other FrontRow components or servers To help organize this important information, we have a Project Planning Template available for

  • FrontRow JUNO, 9 Step 4: Configuring Juno Connect Your Juno Connect has several parameters that can be configured to tell it how to communicate with other devices in an ezRoom or Conductor installation. While each installation is different most of the default parameters will be appropriate. Open a web browser on your laptop and in the URL field type the IPv4 address 192.168.1.103 and press enter. This is the default static IP address of the Juno Connect and will likely be changed when you configure it per the school’s IP addressing scheme. • You will be connected to your Juno Connect and see a screen like this:

  • FrontRow JUNO, CONTENTS Step 1: Before You Begin .......................................................................1 Step 2: Getting Your Configuration Files ..........................................................4 Step 3: Preparing for Configuration ..............................................................5 Step 4: Configuring Juno Connect ...............................................................9 About...................................................................................10 Load/Save . . . . .

  • FrontRow JUNO, YOU’RE ABOUT TO MAKE LEARNING MORE ACCESSIBLE Welcome to FrontRow — the teacher- and tech-friendly way to improve the learning environment in every classroom. To make your configuration of the FrontRow Juno Connect as efficient as possible, we recommend that you first read the section in this guide called Before You Begin. If you follow the steps set out in this Configuration Guide and organize everything you need beforehand, you’ll find setting up your FrontRow Juno Connect classroom communication syste

  • FrontRow JUNO, 21 Appendix A: Control commands for the Juno Connect The following commands can be used in Actions to control how a Juno Connect handles audio: ICR-01 Smart Receiver / Juno Connect Master Volume Commands* Syntax: #AUDn[Mute,Volume]; Name Required/Optional Data Type Format Description n Required Constant 1 Denotes the sub-device. Since the Juno Connect has only one sub device, this is always 1 Mute Optional Variant MCommand where Command is 0, 1, or + Audio mute: • off (0); • on (1); or • tog

  • 13 Command Channel Set the channel (A or B) for which channel the teacher mic is using as the command channel for voice commands. Equalizer Control individual aspects of the sound from your audio devices such as the bass, middle and treble frequencies. Microphone Button Mode The teacher microphone button can be configured to trigger any defined event or to contr

  • FrontRow JUNO, 7 This opens the Internet Protocol (TCP/IP) Properties window. 6. In the General tab, click Use the following IP address, and enter: • IP address: 192.168.1.100 • Subnet mask: 255.255.255.0 • Default gateway: Leave blank NOTE: We recommend 192.168.1.100 as the standard IP address; however, you may need to use a different address if you are using a local switch already using this address 7. Leave the Use the following DNS server addresses fields blank 8. Click OK. 9. Click OK to close each window NOTE: to change your computer back to DHCP follow the same process but select “Obtain an IP address automatically” from the General network page. e. Local Are

  • FrontRow JUNO, 19 10. Event Creator With your collection of discrete Actions defined, you can now specify what Events will cause one or more of those Actions to be executed. Events can be triggered in a variety of ways, via Voice Command, Encore and Teacher Edition software, FrontRow Control panels, a FrontRow push button (CB75 microphone or CB50) or from a non-FrontRow GPI trigger. To create an Event: 1. Click New 2. Name the Event 3. Choose a Trigger. A trigger is a way to invoke the event you are building. Triggers can be physical devices such as a non-FrontRow push button connected to the GPI (GPI open / close), or a FrontRow device connected

  • FrontRow JUNO, 12 PA Release. Sets how quickly the in-room audio returns to its previous level after the announcement is complete Sensitivity. Sets how sensitive the trigger will be for muting the system. The lower the setting, the lower the sensitivity will be. While music is playing in the classroom, make a long announcement over the PA system. Adjust the sensitivity control until you just mute the music. When the announcement stops, the music should return to full volume. 4. System Settings These settings affect the

  • FrontRow JUNO, 1 Make sure you’ve got everything you need to install your FrontRow Juno Connect. By taking the time to prepare, you’ll help ensure the actual set-up is as quick and problem-free as possible. 1. Visualize your goal When your FrontRow Juno Connect is installed, it may look something like this: Step 1: Before you begin LAN

  • FrontRow JUNO, 18 9. Action Creator Actions are specific instructions that are sent to specific devices (e.g. to turn a projector on or change inputs on a projector). Once defined, you will link them to various Events which can be triggered in a variety of ways, including voice commands. To create an Action: 1. Click New 2. Name the Action 3. Enter the action string or Command Actions can be created using two methods: 1. Using a wizard • Select an Action Type using the drop-down list • Enter the syntax necessary to build the specific action 2. Using a Template • Select an Template using the drop-down list • Edit the syntax n

  • FrontRow JUNO, © 2017 FrontRow Calypso LLC Phonic Ear, FrontRow, Calypso and the names of Phonic Ear, Calypso, and FrontRow products are trademarks or registered trademarks of FrontRow Calypso LLC in the U.S. and other countries. 821-5082-146/Rev. E 0317 Installer Assistance: www.gofrontrow.com USA/Global Canada Australia Scandinavia 1690 Corporate Circle 6950 Creditview Road, 629 Nudgee Road Kongebakken 9 Petaluma, CA 94954-6712 Unit 1 Nundah QLD 4012 2765 Smørum United States Mississauga, ON L5N 0A6 Australia Denmark toll-free: 800.227.0735 Canada tel: 1 800 746 642 tel: +45 3917 7101 tel: 707.769.1110 toll-free: 800.340.9894 fax: 1300 737 983 fax: +45 3927 7900 fax: 707.

  • FrontRow JUNO, 5 Estimated time for this step: 5-10 minutes per Juno Connect Here’s where you wake up your Juno Connect and let it know what its mission is. You can of course reconfigure it at any point if your setup changes or you make a mistake — but it’s best to plan ahead so that you don’t have to (see Step 1). For greatest efficiency, we recommend configuring all of your Juno Connect systems all at once in the office prior to going to the installation site, but you can also do it room by room at the school if you prefer. 1. Gather you

  • 8 f. Mac OS X 1. Click the Apple icon in the upper left hand corner of your screen. 2. Click the System Preferences option. 3. In the Internet & Network section click the Network icon. 4. Select the network connection you use to connect to the internet — the one that has a green dot in front of it. The green dot means the connection is active. 5. Click th

  • FrontRow JUNO, 25 I can’t remember what IP address I changed the Juno Connect to, and now I can’t communicate with it 1. Remove the four slot connector from the COM port 2. Disconnect the serial cable (if connected) from the connector 3. Build a shorting plug by connecting the TX and RX lines of connector 4. Power down the Juno Tower 5. Insert the shorting plug (connector) into the COM port 6. Power up the Juno Tower and remove the shorting plug within 3 to 4 seconds 7. If the reset was not successful try again with a shorter or longer time duration before pulling out the plug. 8. A hardware reset changes the IP address back to the default (192.168.1.103) 9. T

  • FrontRow JUNO, 22 For network (NET) commands, we recommend using UDP (“F2”) as the preferred protocol as it tends to be faster. Network (NET) Commands* Syntax: #NET[Connection, String Type. Device ‘Command’]; Name Required/Optional Data Type Format Description Connection Required Variant Fn where n is 1 or 2 Defines the connection type: • TCP/IP (1) • UDP (2) String Type Optional Variant Tn where n is 1 or 2 Defines the string type: • ASCII string (1) • HEX string (2) If you leave StringType blank, a default of T1 is assumed Device Required Variant If using Shortcuts (recommended

  • FrontRow JUNO, 20 5. Add Actions Actions can be added and will be invoked according to the mode chosen in step 4. To add actions, select them and click Add Selected. Actions can be reordered by clicking and dragging the lines to the left of the action name in the Current Action List.

  • 15 Alert Functions Alert Delivered: When a Conductor HTTP alert call is sent, usually by pressing a button in the classroom (on the wall, in software, or using the mic), this automatically confirms to teachers that the alert was delivered to the Conductor Notifier over the network. Alert Acknowledged: When a person presses the “Acknowledge” button in the

  • FrontRow JUNO, 17 7. Command Line Enter Command Use this section to test commands sent to a device to verify that it performs the action desired. Use the drop down list to select examples of FrontRow command protocols. 8. Shortcuts Shortcuts Shortcuts are name substitutions. Defining Shortcuts makes deployment of multiple FrontRow devices of the same type easier. Use Shortcuts in defining actions that represent the IP addresses of the devices you’ll control. This means that your configuration file can be written as a template with IP addresses explicitly defined i

  • FrontRow JUNO, 6 3. Give your computer a static IP address For the duration of the configuration, your computer needs to have a specific IP address. Here’s how to change your computer’s wired network adapter from automatic (DHCP) to fixed (static): a. Windows XP 1. Open Windows Start menu. 2. Open Control Panel. • Classic view: Open Network Connections • Category view: Select Network and Internet Connections, and then Network Connections. 3. Double-click on your active LAN or Internet connection. 4. Click Properties. This opens the Local Area Connections Properties window. Proceed to 3c. b. Windows 7 1. Op

  • FrontRow JUNO, 14 5. Beacon / LCD Overview This page is where you set the color and behavior for the device’s LCD screen, as well as any tone associated with a given alert state. Select a primary color or Do Nothing. Do Nothing will leave the LCD screen unchanged from its current color. In the Pattern column, select Solid or a second color that will alternate with the primary color. IMPORTANT: The ALERT FUNCTIONS should be configured in accordance with the school’s Emergency Preparedness Plan. Download and review the FrontRow Guidelines for a Successful Conductor Deployment at gofrontrow.com/guides-resources for more information. System Functions

  • FrontRow JUNO, 10 2. About Device Information The name you choose should contain meaningful information, such as the classroom number, so that a person accessing the device remotely will have appropriate context. Also on this screen you can see the device MAC address and firmware version. Password If the project requires it you can password-protect the Juno Connect configuration screens by setting a password. If setting a password for the first time, the “old password” is calypso. Choose a new one based on the school’s guidelines and record the informat

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 LSI 620J Manual  lsi/620j-2KV.pdf 23 Jun 2022 16
2 Elite Screens Starling Series Operation & user’s manual elite-screens/starling-series-M87.pdf 21 Mar 2023 4
3 Panasonic Viera X60D series Operating instructions manual panasonic/viera-x60d-series-833.pdf 26 Sep 2022 32
4 Night Owl F SERIES Operation & user’s manual night-owl/f-series-39A.pdf 21 Feb 2023 41
5 Echo BRD-280 Operator's manual echo/brd-280-ES5.pdf 26 Jul 2022 36 1.7 Mb
6 Vortex Kaibab HD Owner's manual vortex/kaibab-hd-474.pdf 13 Aug 2022 5 1.44 Mb

Similar Resources:

  • JVC

    MX-KC2

    (14 pages)
    SCHEMATIC DIAGRAMSMX-KC2Contents   Block diagramStandard schematic diagramsPrinted circuit boards2-12-22-8 to 10CD-ROM No.SML200507COMPACT COMPONENT SYSTEMNo.MB394SCH2005/7COPYRIGHT 2005 Victor Company of Japan, Limited.Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)CA-MXKC2 SP-MXKC2SP-MXKC2Area suff …
  • Vitek

    VT3470 GY

    (20 pages)
    RADIO CASSETTE RECORDERwith CD/MP3 PLAYERMODEL VT3470 GYwww.vitekaus.comINSTRUCTION MANUAL1033473.qxd 27.06.2005 12:14 Page 1Downloaded from www.Manualslib.com manuals search engine Downloaded From Disc-Player.com Vitek Manuals …
  • Aiwa

    XR-MG9

    (16 pages)
    For assistance and information(United States and Puerto Rico)En (English)E (Español)F (Français)MODE D'EMPLOIMANUAL DE INSTRUCCIONESOPERATING INSTRUCTIONSCompact DiscStereo SystemUXR-MG98B-CLR-903-01010601AYK-H-B …
  • Philips

    MCM760

    (2 pages)
    For preview purpose onlyDigital Music with CD RippingRip and relish your favorite CDs to MP3 player on the elegant MCM760 Micro Hi-Fi System with superb sound. Easy, one touch recording - without a PC! And you can enjoy your favourite music on your portable MP3 player.Unlimited listening pleasure• Rip your favorite CDs to MP3• One touch MP3 digital recor …
  • Philips

    MCD170/98

    (33 pages)
    Register your product and get support atwww.philips.com/welcomeMCD170/98 EN User manualZH-TW 使用手冊 MCD170_98_Eng.indd Sec3:1MCD170_98_Eng.indd Sec3:1 12/18/2008 2:27:28 PM12/18/2008 2:27:28 PM …
  • Samsung

    MX-J630

    (23 pages)
    MiNi Hi-Fi Component Audio SystemMP3-CD/WMA-CD/CD-R/RW Playbackuser manualMX-J630imagine the possibilitiesThank you for purchasing this Samsung product.To receive more complete service, please register your product atwww.samsung.com/registerThis Nanum Gothic Eco font is provided by NAVER. …

Comments, Questions and Opinions: