Manualios.com

bintec elmeg RS123 Installation Manual

bintec elmeg RS123 Manual Online:

3.75, 2084 votes
bintec elmeg RS123 User Manual
bintec elmeg RS123 User Guide
bintec elmeg RS123 Online Manual

Text of bintec elmeg RS123 User Guide:

  • 40MHz (HT40) MCS4/12 19 dBm; MCS5/1318 dBm; MCS6/14 17 dBm; MCS7/15 17 dBm TX power @ 5 GHz 802.11n 20MHz (HT20) MCS0/8 23 dBm; MCS1/9 23 dBm; MCS2/10 22 dBm; MCS3/11 21 dBm; MCS4/12 20 dBm; MCS5/1319 dBm; MCS6/14 18 dBm; MCS7/15 18 dBm TX power @ 5 GHz 801.11a/h MCS0 -95 dBm; MCS1 -94 dBm; MCS2 -92 dBm; MCS3 -88 dBm; MCS4 -85 dBm; MCS5 -81 dBm;MCS6 -80 dBm; MCS7 -78dB

  • bintec elmeg RS123, A.6.4 WAN Interface (SFP) STANDARDS IEEE 1000 Base-X SPEED 1000 Mbps full duplex CONNECTOR SFP A.6.5 Wireless WAN Interface WWAN Standard/Bands MC7304: • LTE: B1, B3, B7, B8, B20 • WCDMA: B1, B2, B5, B8 • GSM/GPRS/EDGE: Quad-band Speed (DL/UL) MC7304: CONNECTOR Two SMA female connectors. SIM Slots 1 Mini-SIM (2FF) ISO/IEC 7810:2003, ID-000 (1.8V / 3V) bintec elmeg Technical Information RS123 Router 27

  • bintec elmeg RS123, B.2 Radio WIFI Specifications The Wifi Radio communications is in conformity with standards 802.11a/b/g/n. This product is supplied with antennas. Do not choose other antennas to meet the regulations. Frequency Range 802.11b/g/n @ 2.4 GHz 2400-2483.5 MHz 802.11a/n (HT40) @ 5 GHz 5150-5250 MHz 2550-5350 MHz 5470-5725 MHz Operating 802.11b/g/n (HT20) @ 2.4 GHz 13 Channels 802.11n (HT40) @ 2.4 GHz 9 Channels 802.11a @ 5 GHz 16 Channels 802.11n (HT40) @ 5 GHz 8 Channels TX power @ 2,4 GHz 802.11n 40MHz (HT40) MCS0/8 19 dBm; MCS1/9 19 dBm; MCS2/10 19 dBm; MCS3/11 19 dBm; MCS4/12 19 dBm; MCS5/1319 dBm; MCS6/14 19 dBm; MCS7/15 19 dBm Rece

  • bintec elmeg RS123, Fig. 3: LEDs panel LEDs table LED Color Description POWER Green Off -> Power supply is not connected On -> Power supply is connected. STATUS Green Off -> System off. On -> Software is running. Blinking -> Default configuration. SFP Green Off -> not used On -> SFP is connected. WLAN Green WLAN status LED. Only RS123w and RS123w-4G Devices This LED provides status information about WLAN interface as fol- lows: Off -> interface down. On-> interface up. Blinking -> activity/maintenance. USB Green USB status LED. When an external dongle is used, this LED provides status

  • bintec elmeg RS123, The required notch is located on the rear side of the housing. 3.3 Plug-in Modules The only module that can be inserted in the device is the 3G USB modem. To view the list of supported 3G modems, please visit the following website: http://www.bintec-elmeg.com. 3.3.1 Installation To install the USB modem, simply insert it in the USB slot on the front panel as shown in the following figure: Fig. 9: USB modem insertion slot 3.3.2 Uninstall To remove the device, simply remove it from the slot where it was inserted. 3.4 Power Source The RS123 router is powered with an internal power source. Workplace C

  • bintec elmeg RS123, Fig. 4: ETH LEDs Switch and WAN LED indicator table LED Description Yellow OFF -> Interface is either unavailable, not installed or not registered. ON -> Connected to 10 M: - Steady: Not transferring data. - Blinking: Transferring data. Yellow + Green OFF -> Interface is either unavailable, not installed or not registered ON -> Connected to 100 M: - Steady: Not transferring data. - Blinking: Transferring data. Green OFF -> Interface is either unavailable, not installed or not registered ON -> Connected to 1000 M: - Steady: Not transferring data. - Blinking: Transferring data. 3.1.2 Rear Panel The following figure shows the rear pane

  • bintec elmeg RS123, Chapter 4 Compliance 4.1 Manufacturer Information Brand bintec Manufacturer bintec elmeg Country Germany Postal Address Suedwestpark 94 90449 Nuremberg Germany International Phone +49 - 911 - 9673 0 4.2 Safety Warnings                           

  • bintec elmeg RS123, 3.1.3 Side Panels On RS123w and RS123w-4G Devices, two 3G/4G antenna connectors are located on the side panels, one on each side: Fig. 6: Side panels The connectors are as follows: Side panels connectors Item Description 12 WWAN 3G/4G MAIN and AUX antenna connectors. Only RS123w-4G Devices 3.1.4 Underside Panel The following elements can be found on the underside panel: Fig. 7: Underside panel The following table contains details on the significant elements on the underside panel: Underside panel elements table Item Description A Rubber feet. B Holes for wall mounting. C Internal module SIM tray. bintec elmeg 3 Components and Power Supply RS123 Router 9

  • bintec elmeg RS123, Chapter 1 About This Guide This installation guide for the RS123 router family contains information on how to correctly install the device in a working environment. 1.1 Supported Devices The information provided in this installation guide only applies to the RS123 router family: RS123 Devices. 1.2 Who should read this manual? This manual should be read by the support personnel who need to configure, maintain and monitor the device. 1.3 When should this manual be read? Read this guide as soon as you are ready to familiarize yourself with the device and its components. This manual will help you understand

  • bintec elmeg RS123, Appendix A Technical Information A.1 Troubleshooting The following table can help you solve problems when installing the device. If you cannot solve the problem, contact your dealer for more information. Symptom Solution None of the LEDs lights up on the router. Check the power supply to the router (power source, ON/OFF switch, main power outlet). You have forgotten the access password for the router. Ignore the configuration through the RESET button (as explained in the relevant section). None of the

  • lems of drivers and other components. 3.4.2 Connecting • Ensure that the on/off power supply switch is in the OFF position. • Connect all data cables. • Connect the power supply to the device. • Set the device’s on/off power supply switch in the ON position. 3.4.3 Disconnecting • Set the on/off power supply switch in the OFF position. • Disconnect the power supply from the devi

  • bintec elmeg RS123, Fig. 14: USB Connector 3.6.6 Connecting for Configuration The RS123 router has an USB Type B connector on the front panel labeled “Console”, which provides access to the device local console. For further information, please see Connecting to the device on page 23. Fig. 15: CONSOLE Connector 3.7 Installing the SIM card The RS123 family has a Wireless WAN interface that, in order to operate, may require a SIM card to be inserted into the device. Certain services (CDMA) provided by several carriers in some countries do not require SIM cards. The RS123 has one internal SIM

  • bintec elmeg RS123, A.6.4 WAN Interface (SFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A.6.5 Wireless WAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A.6.6 Wireless LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 A.6.7 USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 A.6.8 Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 A.6.9 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 A.6.10 Dimensions and weight . . . . . . . . . . . . . .

  • Fig. 19: CONSOLE Connector To configure this, you must connect the “CONSOLE” port to your PC using a USB cable. Note The configuration for the terminal must be: - Speed: 115200 bps. - Eight data bits. - One stop bit. - No parity bit. - No type of flow control. A.4 Licenses The RS123 router family offers a series of licenses among which the following stand out: SFP: Activation licen

  • bintec elmeg RS123, Legal Notice Warranty This publication is subject to change. bintec elmeg offers no warranty whatsoever for information contained in this manual. bintec elmeg is not liable for any direct, indirect, collateral, consequential or any other damage connected to the de- livery, supply or use of this manual. Manual bintec elmeg 2 RS123 Router

  • bintec elmeg RS123, 2.2.2 Hardware Monitoring The LEDs on the front panel are used to monitor the hardware in the RS123 router. These LEDs provide visual in- formation on the state of the device and reference the condition of the hardware components, indicating whether- there is connectivity, data flow, etc. For further information on the LEDs panel, please see Components on page 6. bintec elmeg 2 RS123 Devices RS123 Router 5

  • bintec elmeg RS123, & 1"   1  *"  =   >  ?:  @    $ 4    ' 7 A     

  • bintec elmeg RS123, A.6.6 Wireless LAN Interface WLAN standards 802.11n (Mimo 2x2); 802.11b; 802.11g; 802.11a; 802.11h. Frequency bands 2.4 GHz in- door/outdoor (EU) 2.4 GHz Indoor/Outdoor (2412-2472 MHz) max. 100 mW EiRP. The permitted transmission powermay vary in countries outside the EC. Frequency bands 5 GHz indoor (EU) 5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed. The permitted trans- missionpower may vary in other countries. Frequency bands 5 GHz out- door (EU) 5 GHz outdoor (5470-5725 MHz) max. 200 mW EiRP allowed. The permit- tedtransmission power may vary in other countries. WLAN mo

  • bintec elmeg RS123, 3.2 Installation 3.2.1 Installation in a rack The RS123 device family can be installed in a 19” rack. The strips and screws needed are provided by default. Both strips are attached to the device through 8 screws (4 on each side), as shown in the figure: Fig. 8: Anchor bolts for a rack 3.2.2 Standalone RS123 devices can be placed as a standalone on a flat, stable surface. The adhesive rubber feet must be stuck to the underside panel to stop the router from sliding. Make sure there is enough space around the router (for ventilation purposes) and check that the elect

  • bintec elmeg RS123, Table of Contents I Related Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1 About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.4 What is in this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.5 What i

  • bintec elmeg RS123, 3.6.1 4-port Ethernet Switch The RS123 router family incorporates a 4-port 10/100/1000 BaseT Switch with automatic MDI/MDIX to connect to a local area network (LAN). Please pay careful attention to the labeling so you do not mix this switch with other types of ports: Fig. 10: LAN switch PORTs Note During booting and in BIOS mode, only the ETH 1 connector is available. 3.6.2 WAN Connection The RS123incorporates an Ethernet interface for WAN connection. This port has 2 connectors - SFP for optical link and R

  • bintec elmeg RS123, • 802.1Q (VLAN) • 1000 BASE-X Types • LX/LH (single-mode 1310 nm) • SX (multi-mode 850 nm) • ZX (single-mode 1550 nm) Speed • 1000 Mbps full duplex Warning SFP modules to be installed in the card socket should be class 1 devices complying with standard IEC- 60825-1. 3.6.3 WWAN Antenna Connection (3G/4G connector) The RS123 router family has two connectors for WWAN antennas. To assemble and disassemble the antennas sup- plied, simply screw them into the connectors labeled 3G/4G (located on the side panels of the router). Note This c

  • bintec elmeg RS123, A.5.2 WAN Connector RJ45 WAN RJ45 PIN FE Signals GE Signals 1 2 3 4 5 6 7 8 BI-DA+ BI-DA- BI-DB+ -- -- BI-DB- -- -- BI-DA+ BI-DA- BI-DB+ BI-DC+ BI-DC- BI-DB- BI-DD+ BI-DD- A.5.3 WWAN Connector (female) PIN ANT Internal External RF in/out GND A.5.4 WLAN Connector (male) PIN ANT Internal External RF in/out GND A.5.5 USB Connector USB Type A PIN USB 1 2 3 4 Shell VCC DATA- DATA+ GND Shield bintec elmeg Technical Information RS123 Router 25

  • bintec elmeg RS123, tance between the device and the base station, physical obstacles and other interferences caused by radiofrequen- cies (RF). For optimum coverage, carry out the following instructions: • Whenever possible, place the antenna where there are no physical obstacles. Obstacles between the antenna and the base station degrade the wireless signal. Place the antenna above ground level facing the nearest base sta- tion. • Density of materials also affects the antennas. Place them away from any type of walls, metal screens, mirrors, etc. • Do not place the antenna near columns, which may throw shadows and reduce the coverage area. �

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Hitachi RAS-10KH3 Instruction manual hitachi/ras-10kh3-349.pdf 12 Dec 2023 80 4.31 Mb
2 Vivotek IP3112 Quick installation manual vivotek/ip3112-5T2.pdf 17 Dec 2022 6 1.06 Mb
3 HP dvd1035i Manual  hp/dvd1035i-9J1.pdf 26 Oct 2023 2
4 Electrolux Dito 601792 Specifications electrolux/dito-601792-92F.pdf 29 Jan 2023 4 0.25 Mb
5 Electrolux EMS26415X Operation & user’s manual electrolux/ems26415x-XQ2.pdf 17 Jan 2024 36 1.31 Mb
6 Haier MHMK-6TP Operation & user’s manual haier/mhmk-6tp-QBF.pdf 19 Jan 2023 36 7.06 Mb

Similar Resources:

  • Four-Faith

    F3936-3436H

    (79 pages)
    F3936-3X36H Series Router User ManualThe user manual is suitable for the following model:F3936-3x36H SeriesRouterUser ManualDocumentation No. Product Version PageV1.0Product Name: F3936-3X36H Total:79Model Product TypeF3936-3436HWCDMA&HSDPA&HSUPA&HSPA+ROUTERF3936-3636HCDMA2000 1X EVDO ROUTERF3936-3736HLTE&TD-SCDMA ROUTERF3936-3836HLTE&W …
  • ZyXEL Communications

    P-660H Series

    (2 pages)
    Cost-effective Ultra High-Speed ADSL2+ Gateway for SOHO NetworksADSL2+ 4-port Gatewayp-660h seriesBenefitsHigher Speed Internet AccessZyXEL P-660H Series is an all-in-one affordable router, compatible with high-speed ADSL, ADSL2 and ADSL2+ interfaces over existing copper lines. With speed up to 12 Mbps (ADSL2) or 24 Mbps (ADSL2+), the P-660H Series offers hi …
  • Juniper

    EX2200

    (2 pages)
    Connecting AC Power to an EX2200 SwitchThe power supply in an EX2200 switch is located on the rear panel.Ensure that you have the following parts and tools available:■ A power cord appropriate for your geographical location■ A power cord retainer clipEnsure that you have connected the switch chassis to earth ground.CAUTION: To meet safety and electromagn …
  • Mitsubishi Electric

    Central Controller G-50A

    (24 pages)
    Central ControllerModel: G-50AMitsubishi Electric Air-conditioner Network SystemOperation Manual(Initial Setting Tool Version)Contents1Introduction 11-1Conventions Used in this Manual11-2Computer Requirements12Installing and Uninstalling Initial Setting Tool22-1Installing Initial Setting Tool22-2Uninstalling Initial Setting Tool32-3Starting and Closing the P …
  • Weidmuller

    IE-SW-AL14M-12GT-2GESFP

    (2 pages)
    1 2 3 Hardware Installation Guide Managed Gigabit Ethernet Switch IE-SW-AL14M-12GT-2GESFP (Part No. 2682360000) 1. Introduction Ethernet Switches from Weidmüller are designed for industrial applications and fitted with a robust housing. To ensure reliable, error-free operation, and to prevent damage or injury, please read the operati …
  • Makita

    RP0900

    (48 pages)
    RP0900 ENRouter INSTRUCTION MANUAL 7ZHCN雕刻机 使用说明书13IDFrais Tangan PETUNJUK PENGGUNAAN 19MSPenghala MANUAL ARAHAN 25VIMáy Phay Cầm Tay Hoạt Động Bằng Động Cơ ĐiệnTÀI LIỆU HƯỚNG DẪN 32TH 38 …

Comments, Questions and Opinions: