Nokia 7210 SAS-M Configuration Manual

Text of Nokia 7210 SAS-M User Guide:

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 93 VPLS IGMP Snooping VPLS (Multicast traffic with IGMP snooping enabled) SDP to SAP SDP to SDP Source and Destination MAC, Ingress Port Id Source and Destination MAC, Ingress Port Id VPRN service: SAP to SAP SDP to SAP Source and Destination IP, Source and Destination L4 ports Source and Destination IP, Source and Destination L4 ports, Ingress port-Id VPRN service: SAP to SDP Source and Destination IP, Source and Destination L4 ports Source and Destination IP, Source and Destination L4 ports, Ingress port-Id IES service (IPv4): IES SAP to IES SAP Source and Destination IP,

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 95 ECMP Hashing fields used for 7210 SAS devices in Network mode Table 16: ECMP Hashing mechanism for services configured on 7210 SAS devices in network. Services Traffic Type A B ECMP Hashing IP (For routed traffic) Unicast traffic Network Port IP Interface Network Port IP Interface • Source and Destination IP • Source and Destination L4 ports • Ingress Port-Id IES IPv4 traffic SAP or Network Port IP interface SAP or Network Port IP interface

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 325 Fragments The total number of packets received that were shorter than 64 octets (excluding framing bits but including FCS octets) that had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Jabbers The total number of packets received that were longer than 1518 octets (excluding framing bits but including FCS octets) that had either a bad Fr

• Nokia 7210 SAS-M, LAG Commands Page 220 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide This command configures the encapsulation method used to distinguish customer traffic on a LAG. The encapsulation type is configurable on a LAG port. The LAG port and the port member encapsulation types must match when adding a port member. If the encapsulation type of the LAG port is changed, the encapsulation type on all the port members will also change. The encapsulation type can be changed on the LAG port only if there is no interface associated with it. If the MTU is set to a non default value, it will be reset to the default value when the encap type is changed. The no form of this

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 343 *A:hw_sasm_duta>show# port 1/1/1 ethernet lldp nearest-bridge ============================================================================== Link Layer Discovery Protocol (LLDP) Port Information ============================================================================== Port 1/1/1 Bridge nearest-bridge ------------------------------------------------------------------------------- Admin State :

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 189 This command associates the context to which it is configured to the operational group specified in the group-name. The oper-group group-name must be already configured under config>system context before its name is referenced in this command. The no form of the command removes the association. Parameters name — Specifies a character string of maximum 32 ASCII characters identifying the group instance. Values [32 chars max] qinq-etype Syntax qinq-etype 0x0600.

• Nokia 7210 SAS-M, Port Show Commands Page 336 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Sync. Status Msg. : Enabled Rx Quality Level : failed Tx DUS/DNU : Disabled Tx Quality Level : 0x2(prc) SSM Code Type : sdh Down On Int. Error : Disabled CRC Mon SD Thresh : Disabled CRC Mon Window : 10 seconds CRC Mon SF Thresh : Disabled Configured Address : c4:08:4a:7a:ad:e3 Hardware Address : c4:08:4a:7a:ad:e3 Transceiver Data Transceiver Type : SFP Model Number : 3HE00062CBAA01 ALA IPUIBDYDAA TX Laser Wavelen

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 165 qos Syntax qos policy-id no qos Context config>port>ethernet>access>egress Description Platforms Supported: 7210 SAS-M, 7210 SAS-T (Access-uplink mode and network mode) 7210 SAS-X, 7210 SAS-Sx/S 1/10GE, 7210 SAS-Sx 10/100GE, 7210 SAS-Mxp, 7210 SAS-R6, and 7210 SAS-R12. This command associates a access-egress QoS policy to the access port. On 7210 SAS-M and 7210 SAS-T in access uplink m

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 63 LAG Hashing Fields used for 7210 SAS-X Table 9: LAG Hashing mechanism for services configured on 7210 SAS-X devices Services and Traffic Direction (For example: SAP to SDP) Packet fields used for Hashing for different traffic types VPLS service: SAP to SAP SAP to SDP IP traffic (Learnt and Unlearnt): Source and Destination IP, Source and Destination L4 ports, VLAN, Ingress Port-Id. PBB traffic: BDA, BSA, ISID, Ingress Port-Id. MPLS traffic: MPLS label stack (Two labels deep), Ingress Port-Id. Non-IP traffic (learnt and unlearnt): Source and Destination MAC,

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 107 Figure 9: 802.1x Authentication Scenario The messages involved in the authentication procedure are illustrated in Figure 9.The router will initiate the procedure when the Ethernet port becomes operationally up, by sending a special PDU called EAP-Request/ID to the client. The client can also initiate the exchange by sending an EAPOL-start PDU, if it doesn't receive the EAP-Request/ID frame during bootup. The client respon

• Configuration Notes for provisioning of 7210 SAS-R6 IMM-c cards Page 126 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Configuration Notes for provisioning of 7210 SAS-R6 IMM-c cards The user has an option to aggregate 1G and 10G customer services to 100GE uplinks to meet the increasing bandwidth needs in access networks by provisioning of 7210

• Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 275 2 1 imm-sas-10sfp+1xfp up up MDA Specific Data Maximum port count : 11 Number of ports equipped : 11 Network ingress queue policy : default Capabilities : Ethernet Hardware Data Platform type

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 293 Detailed Port Output Fields Detailed Port Output — The following table describes detailed port output fields. Label Description Description A text description of the port. Interface The port ID displayed in the slot/mda/port format. Speed The speed of the interface. Link-level Ethernet — The port is configured as Ethernet. MTU The size of the largest packet which can be sent/received on the Ether- net physical interface, s

• Standards and Protocol Support 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 385 MPLS — RSVP-TE RFC 2702, Requirements for Traffic Engineering over MPLS is supported on K12, M(N), T(N), X, Mxp, Sx/S-1/10GE, Sx-10/100GE, R6, and R12 RFC 2747, RSVP Cryptographic Authentication is supported on K12, M(N), T(N), X, Mxp, Sx/S- 1/10GE, Sx-

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 133 Configuring Channelized Ports This section is applicable only when using the CES MDA that supports 4 x T1/E1 ports. CES MDA is available for use only on the 7210 SAS-M platform in network mode (it cannot be used in access-uplink mode). It cannot be used on any other 7210 SAS platform. When configuring channelized ports, the port ID is specified in different ways depending on the MDA type and level of channelization. Ethernet ports

• Nokia 7210 SAS-M, Multi-Chassis LAG Page 114 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide MTU Configuration Guidelines • The 7210 SAS devices provides an option to configure the MTU limitations at many service points. The physical (access and network) port, service, and SDP MTU values must be individually defined. • MTU values must conform to both of the following conditions: − The service MTU must be less than or equal to the SDP path MTU. − The service MTU must be less than or equal to the access port (SAP) MTU. Default MTU Values Table 17 displays the default MTU values which are dependent upon the (sub-

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 319 Broadcast Pckts : 0 Drop Events : 0 Multicast Pckts : 0 CRC/Align Errors : 0 Undersize Pckts : 0 Fragments : 0 Oversize Pckts : 0 Jabbers : 0 Collisions : 0 Octets : 1408 Packets : 0 Packets of 64 Octets : 22 Packets of 65 to 127 Octets : 0 Packets of 128 to

• Nokia 7210 SAS-M, Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Page 253 Output Show Card Output — The following table describes show card output fields. *A:MTU-A# show card =============================================================================== Card Summary =============================================================================== Slot Provisioned Equipped Admin Operational Card-type Card-type State State ------------------------------------------------------------------------------- 1 iom-24g iom-24g up up

• Nokia 7210 SAS-M, LAG Hashing Fields used for 7210 SAS-Mxp Page 84 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide VPLS Service: SAP to SDP IP traffic (Learnt): Source and Destination IP, Source and Destination L4 ports IP traffic (Unlearnt): Hash-2 and parameter under hash-2 used. MPLS traffic (Learnt): Source and Destination MAC, VLAN MPLS traffic (Unlearnt): Hash-2 and parameter under hash-2 used. Non-IP traffic (Learnt): Source and Destination MAC, EtherType, VLAN Non-IP traffic (Unlearnt): Hash-2 and parameter und

• General Port Commands Page 172 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide Hybrid: A hybrid Ethernet port allows the combination of network and access modes of operation on a per- VLAN basis and must be configured as either dot1q or QinQ encapsulation. When the hybrid port is configured to the dot1q encapsulation, the user configures a SAP inside a service by providing th

• Nokia 7210 SAS-M, Port Monitor Commands Page 364 7210 SAS M, T, X, R6, R12, Mxp, S, Sx Interface Configuration Guide ------------------------------------------------------------------------------- At time t = 0 sec (Base Statistics) ------------------------------------------------------------------------------- Octets 0 0 Packets 39 175 Errors 0 0 ------------------------------------------------------------------------------- At time t = 3 sec (Mode: Absolute) -----------------

More Instructions:

	Nokia 7210 SAS-M Quality of service manual 14-12-2023 514	DOWNLOAD
	Nokia 7210 SAS-M Installation manual 31-05-2023 91	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Leviton QuickPort USOC Snap-In Connector 41106-R*6 (1 pages) QuickPort®USOC Snap-In ConnectorDESCRIPTIONLeviton’s QuickPort USOC Snap-In Connectors feature awiring configuration label for quick and easy wiring.INSTALLATION1. Remove jacket from cable.2. Check jack termination label (located on sides ofjack) for wiring standard and associated color codes.The label also includes jack pin numbers. (Figure 1)3. Route th …

• Cisco TOPSPIN SFS 3012 (79 pages) Part Number: OL-7722-01 Cisco SFS 3012 Multifabric Server Switch Hardware Guide (Topspin 360 Hardware Guide)Web Release v2.1.0Product ID: 140262 …

• LevelOne IFP-0504 (2 pages) 5-Port Fast Ethernet Industrial PoE Switch, 4 PoE Outputs, 802.3at PoE Plus, 1 Port ST MultiQuick Installation Guide IFP-0504 Port Fast Ethernet Industrial PoE Switch, 4 PoE Outputs, 802.3at PoE Plus, 1 Port ST Multi-Mode Fiber, 2kmQuick Installation Guide Port Fast Ethernet Industrial PoE Switch, Mode Fiber, 2km Quick Installation Guide v1.0 IFP-0504 …

• Harwil Q-8DS (4 pages) ULTRA RELIABLE SINCE 1956 P. 1HARWIL CORPORATION541 KINETIC DRIVE, OXNARD, CA 93030TEL: (805) 988-6800 FAX: (805) 988-6804EMAIL: [email protected] Q-8DSPARTS LISTFLUID FLOW SWITCHO-RINGBODY, COMPLETE WITHFEED THRU SHAFT ASSEMBLY(SEE PARTS LIST)1” NPTSTRAIN RELIEF NUTGROMMET ‘A’GROMMET ‘AA’GROMMET ‘B’GROMMET ‘C’SWITCH COVER4 RETAINING S …

• Interlogix IFS ANT-UNI-21DB-2G (2 pages) P/N 1073057 • REV A • 16OCT15 1 IFS ANT-UNI-21DB-2G Quick Start GuideContent Package Contents 1 Installation Steps 1 Specifications 1 Contact information 2 This is the IFS ANT-UNI-21DB-2G Quick Start Guide. This document provides basic instructions for installing and using the IFS ANT-UNI-21DB-2G. Package Contents Thank you for purchasing th …

• American Dynamics SpeedDome Optima LT (24 pages) Over 175 SpeedDome programmable dome cameras keep tabs on major traffic arteries throughout central Florida. From Orlando to Tampa and out to Cape Canaveral, American Dynamics domes put state transportation officials front and center at the scene of an accident or suspicious activity. Video feeds supply key information to law enforcement and news media duri …

Comments, Questions and Opinions: