Bang & Olufsen BeoVision 4-85 Installation Manual
|
Bang & Olufsen BeoVision 4-85, Installation, TV 11 Installation, TV Placement of TV in packaging The purpose of this step is to place the BeoVision 4-85 in its packaging in an appropriate place. The aim is to obtain as less movement of the TV as possible, which is a great advantage when moving large objects. It is prudent to conduct a test run of the transport without the TV mounted on the crane. See the example below. When the test run seems to proceed sensible, place the TV in its packaging where planned. ! Be careful with covering the oor with protection materi
Installation, Floor Stand 7 Removal of Floor Stand packaging When the product is placed in its packaging the next step is to remove the packaging parts. Follow the procedure below: Assembly of Floor Stand The Floor Stand is now ready for assembly. When the Floor Stand is assembled it is ready to be placed by a crane. Follow the procedure below: > Unlock all clips in the packaging as shown
Bang & Olufsen BeoVision 4-85, Assembly of cabinet parts 18 Assembly of cabinet parts Survey of mounted back covers: Cabinet 3 ➀ ➁ ➁ Cabinet 1 (TV) Cabinet 2 (Stand) Cabinet 3 (Speaker) Safety bolt / inspection hatches Safety bolt / inspection hatches Mains inlet >>> Left Right > Mount springs for the TV cabinet (from ‘Cabinet 1’ bag). > Mount Cabinet 3 (speaker - use screws from ‘Cabinet 3’ bag). > Mount the cable clamp as shown ➀ ). TX25 TX30
Bang & Olufsen BeoVision 4-85, Contents / Installation overview 28 Introduction Warning/Precautions Installation overview Installation, Floor Stand Installation, TV Installing the TV on the Floor Stand Installing shielding frames Connection of cables to the TV Horizontal TV adjust Assembly of cabinet parts Connection of BeoVision 4-85 / BeoSystem 3 Installing BeoLab 10 Setting-up PDP settings Installation on the Japanese market Technical specications Contents Introduction ...................................................................................... 2 How to navigate this guide ..........
Bang & Olufsen BeoVision 4-85, Installation, Floor Stand 9 > Before the Floor Stand placement is completed, connect the wire safely from the stand plate to the wire from the stand leg (shown here). Pull gently at the wire on the top of the tube before lowering the stand legs. > Carefully place the two legs of the Floor Stand (move the guide pins into the holes in the legs) to the stand plate. ! Again, it is recommended to be at least three persons to do the procedure. One to operate the crane and two to place the two stand legs smooth and precisely. > When the stand legs are placed correctly mount and tighten the six screws for each le
Bang & Olufsen BeoVision 4-85, Assembly of cabinet parts 19 Cabinet 2 > Lead the cable bundle (from the Floor Stand and the TV) through the cable hole in the Stand cabinet. > Turn the eccentric adjustment screw clock-/counterclockwise to move the position of the knob in horizontal/vertical direction. The aim is to obtain that ‘A’ is equal to ‘B’. Cabinet 1 Eccentric screw A B > Mount Cabinet 1. > Attach the wall bracket for BeoSystem 3 to the pre-drilled holes on cabinet 2 and mount BeoSystem 3. > Mount the two safety bolts for cabinet 1in the inspection holes. TX30 (x2) TX20 (x6) > Mount th
Bang & Olufsen BeoVision 4-85, Installation, TV 13 Removal of TV from packaging The TV is now free-standing and ready for transport. When the TV is removed and free from the packaging the plates and the EMC gaskets must be installed. Follow the procedure below (depending of the crane type the procedure may vary): > Mount the eyebolt in the centered thread hole as shown below: > Place the crane in front of the TV and secure the crane claw to the eyebolt on the TV. > Lift off the TV from the packaging (it is recommended to have at least one person steering the crane and two persons steering the TV to prevent damaging the product). > Pull the crane with the TV away from the packa
Bang & Olufsen BeoVision 4-85, Installation, Floor Stand 6 Installation, Floor Stand The elements in the Floor Stand installation consists of Floor Stand assembly ( ➀ ) and TV placement ( ➁ ) ➀ To ensure a smooth installation it is recommended to follow a structured procedure. Please follow the suggested procedure below: - Place the Floor Stand in its packaging. - Remove the Floor Stand packaging. - Assemble the Floor Stand. - Place the Floor Stand. - Align the feets of the stand plate. Placement of Floor Stand in packaging The purpose of this step is to place the Floor Stand in its packaging in an appropriate place. The aim is to
Bang & Olufsen BeoVision 4-85, Installing the TV on the Floor Stand 15 Installing the TV on the Floor Stand The TV is now ready to be installed on the Floor Stand. Move the crane with the TV to the Floor Stand. > Move the position of the TV and align to t the four eyebolts to the mounting holes on the Floor Stand (see below). ! It is recommended to have at least one person steering the crane and two persons steering the TV to prevent damaging the product. > Lower the crane arm carefully and release the hook from the eyebolt. > Remove the cra
Bang & Olufsen BeoVision 4-85, Installing BeoLab 10 21 Installing BeoLab 10 Mount the center speaker (BeoLab 10) to the Floor Stand. 5mm (x4) > Mount the speaker bracket for BeoLab 10 onto the speaker plate on the Floor Stand the four supplied screws ‘ ’ for BeoLab 10 wall bracket. > Mount BeoLab 10 onto the BeoLab 10 wall bracket. ! It is very important that BeoLab 10 is fully attached to the wall bracket, otherwise there is a major risk of damaging the TV when it is moving to standby position. > Mount the Power Link cable and the mains cable from the cable chain to BeoLab 10. > Mount the front cloth.
Warning / Precautions 3 Warning Before the installation is started it is strongly recommended to ensure the following: ! Ensure that the oor construction is strong enough to support long-term use. If its strenght becomes insufcient over the course of long-term use, the product may tip over, and possible causing injury. ! Installation and removal should be carried out by qua
Bang & Olufsen BeoVision 4-85, Installation overview 5 Weight When the TV or the stand needs to be moved, a crane can be used (recommended). The items are too heavy to move and it is strongly recommended to not attempt lifting them manually. ! Only moving company are allowed to lift or move the TV and Floor Stand. Not technicians or installers. There is no requirements to which type of crane to use, but in order to attain a smooth and safe operation, it is recommended to use a crane like this: L = 95-135 cm, length of reach H = ≥ 235 cm (height) W = ≥ 98 cm (width) Hw = ≤ 18 cm (height of wheels) The weight of BeoVision 4-85 is approx. 145 kg and approx. 260 kg for the Floor Stand.
Bang & Olufsen BeoVision 4-85, Introduction 2 Introduction The aim for this guide is to assist the installer to attain a smooth and correct installation. The guide is intended as a guideline and may in certain cases not be 100% relevant. However, the guide could be useful as a reference book to nd informations and dimensions about the products. Content The main content of the Installationguide describes the following: - Precautions - Assembly and installation of Floor Stand - Mechanical specications for BeoVision 4-85, Floor Stand. I
Bang & Olufsen BeoVision 4-85, Installing shielding frames 16 Installing shielding frames Install the four shielding frames (MDF supplied with the TV) in the following order: Shielding frame Screws > Shielding frame top. > Shielding frame bottom. >>> ! It is important that tongued and grooved ts perfectly. > Shielding frame left/right. > Conrm correct wiring for auto contrast and camera (ACM) > Tighten the 20 screws to lock the shielding frames. >>> Shielding frame
Bang & Olufsen BeoVision 4-85, Setting-up PDP settings 22 Setting-up PDP settings - Locate the label on the back side of the TV and write down the printed values: - Switch on BeoVision 4-85 by pressing TV and await the product to start up. - Enter Service Menu by pressing: MENU 00 GO/OK. Choose: MONITOR - PICTURE ADJUSTMENTS - PANEL/PW ADJUST and enter the values from the upper label. Choose: MONITOR - PICTURE ADJUSTMENTS - MONITOR SETTINGS - PANEL/PW 3D ADJUST and enter the values from the lower label. - Key in the values as written down earlier, and exit Service Me
Connection of BeoVision 4-85 / BeoSystem 3 20 Connection of BeoVision 4-85 / BeoSystem 3 The next step is to connect the necessary cables to BeoSystem3, set-top boxes, to mains etc. Follow the procedure below: > Connect the necessary cables (HDMI, Camera/IR, PowerLink, RS232, stand and mains cables) to BeoSystem 3. > Connect the desired number of set-top boxes to the respective
Bang & Olufsen BeoVision 4-85, Connection of cables to the TV / Horizontal TV adjustment 17 Connection of cables to the TV Connect the cables from the cable chain to the connectors on the TV: Control/Camera module: > HDMI cable - to BS3 > RS232 cable - to BS3 > 3D shutter out - to 3D socket > Camera cable - from camera module > IR-out cable - to BS3 > Auto contrast cable - from auto contrast > IR/blast cable (3D) - from IR-bar IR/blast cable: Secure the cable with cable ties as shown. Television mains inlet: > Co
Bang & Olufsen BeoVision 4-85, Installation, TV 12 Removal of TV packaging When the product is placed in its packaging the next step is to remove the packaging parts. Follow the procedure below: > Remove the securing belts > Remove the top packaging > Remove the front packaging > Remove the four frame parts > Remove the three foam parts > Remove sides and the back part
Bang & Olufsen BeoVision 4-85, Installation overview 4 Installation overview Apart from the Floor Stand, the basic set-up of BeoVision 4-85 includes the following items: - BeoVision 4-85 PDP (Plasma Display Panel) incl. IR, ACM and shielding frames - BeoSystem 3 - BeoLab 10 The Floor Stand installation includes: - Floor Stand with motorised speaker bracket (incl. accessorie bags with e.g., EMC caps, washers, screws etc.). - Cabinet parts (TV cabinet, speaker cabinet and stand cabinet). - Decorative plates. - BeoLab 10 wall bracket (attached to the speaker bracket). Floor Stand installation Introduction Warning/Precautions Installation overview Installation, Floor Stand Installation, TV Installin
Bang & Olufsen BeoVision 4-85, Installation, Floor Stand 8 ! Be careful not to damage the cables and the cable holders with the lashing belt when the stand is lifted. > Lift off the Floor Stand chassis from the packaging. It is recommended to have at least one person steering the crane and two persons steering the Floor Stand chassis to prevent damaging the product. > Pull the crane with the Floor Stand chassis away from the packaging and move it to the stand plate. > Place the oor stand plate on the top of the two bars as shown. Assure that the assembly area under the fortication poin
Bang & Olufsen BeoVision 4-85, Installation, TV 14 Replacing stand hooks on TV The next step is to remove the stand hooks (as delivered from factory). This is necessary to be able to attach the TV to the Floor Stand. Follow the procedure below: AA B C (x2) (x2) A B C 10 mm 14 mm > Mount the two eyebolt caps (L/R) from position A in position C as shown. > Mount the two new eyebolts (L/R) including the EMC washers (position A) as shown. > Mount the two new eyebolts (L/R) including the washers/EMC washers (position B) as shown. > Remove the two eyebolt caps (position A). > Remove the four stand hooks (position B and C). >>> * (x2) A B C *
DOWNLOAD |
Panasonic TH-37PV60E Plasma TV Gebruiksaanwijzing
TH-37PV60E |
Samsung PN43F4500 Plasma TV Operation & user’s manual
PN43F4500 |
Bang & Olufsen BeoVision 7 Plasma TV Operation & user’s manual
BeoVision 7 |
Zenith Z42PX21D Plasma TV Installation and operating manual
Z42PX21D |
Bang & Olufsen BeoVision 4 Plasma TV Reference book
BeoVision 4 |
Hitachi 32LD960DTA Plasma TV Specifications
32LD960DTA |
Samsung UN46F7500AF Plasma TV Quick start manual
UN46F7500AF |
Panasonic Viera TX-P42U20E Plasma TV Operating instructions manual
Viera TX-P42U20E |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Brother | T74 | Owner's manual | brother/t74-PTF.pdf | 31 Jul 2022 | 98 | 1.68 Mb |
2 | Thule | 150 | Mounting & installation | thule/150-LR4.pdf | 20 Dec 2022 | 1 | 0.46 Mb |
3 | Intel | SR2600UR - Server System - 0 MB RAM | Service manual | intel/sr2600ur-server-system-0-mb-ram-6J9.pdf | 02 Mar 2024 | 234 | |
4 | Peavey | Cyberbass 5 | Operating manual | peavey/cyberbass-5-P16.pdf | 10 Jul 2023 | 30 | 3.21 Mb |
5 | OWI | IWST52 | Specifications | owi/iwst52-VMZ.pdf | 09 Jun 2023 | 2 | |
6 | Clarke | Hippo4A | Operation & maintenance instructions manual | clarke/hippo4a-Q41.pdf | 31 Jul 2023 | 11 | 0.12 Mb |
Akai
50” Plasma TelevisionPDP5074HNCHome theater experiences defined by AKAI technologyProducts styled for you, performance to enrich your life. Whether your application is simple or demanding, Akai technology will support your lifestyle.Breathtaking visual performance• 1366 x 768 native resolution for optimal HDTV performance• High Luminance Plasma Display …
PDP5074HNC(2 pages) |
Panasonic
Customer’s RecordThe model number and serial number of this product may be found on its rear panel. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.Model Number Ser …
TH-P54Z1Z(60 pages) |
Samsung
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.Still image warningAvoid displaying still images (like jpeg picture files) or still image element (like TV programme logo, panorama or 4:3 …
Series 4+(2 pages) |
Panasonic
TVRECVCR DVDVCRTEXTNEXITTV/AVGUIDEF.P. INDEX HOLD123456789C0PROGRAMMEDIRECT TV RECASPECTMENUOKGebruiksaanwijzingPlasmatelevisieNederlandsLees deze instructies voordat u het toestel in gebruik neemt. Bewaar de instructies voor eventuele naslag.De afbeeldingen in deze handleiding zijn slechts een voorbeeld.Modelnummer TH-37PV60ETH-42PV60E
…
TH-37PV60E(32 pages) |
Samsung
СтранаЦентр поддержки покупателей Веб-узелESTONIA 800-7267 www.samsung.eeLATVIA 800-7267 www.samsung.com/lvLITHUANIA 8-800-77777 www.samsung.ltKAZAHSTAN 8-10-800-500-55-500 www.samsung.kzKYRGYZSTAN 00-800-500-55-500 -RUSSIA 8-800-555-55-55 www.samsung.ruTADJIKISTAN 8-10-800-500-55-500 -UKRAINE 8-800-502-0000 www.samsung …
ATIV Smart PC Pro 5(150 pages) |
LG
OWNER’S MANUALPLASMA TVPlease read this manual carefully before operating your set and retain it for future reference.PN45**PN65*P/NO : MFL67648602 (1305-REV03)Printed in Koreawww.lg.com
…
PN45 Series(48 pages) |
Asus Network Router RT-AC55UAsus RT-AC55U User Guide (Doc Type: Network Router Quick start manual) RT-AC55U, 81 |
Astrolite Light Fixture HELIOS 3WLight Fixture PDF Operation & user’s manual HELIOS 3W, 5 |
NETGEAR Wireless Router C3000#4E6Y95 C3000: NETGEAR Wireless Router Owner Documentation C3000, 2 |
Mazda Automobile 6 2006#ZR8N94: 6 2006 Automobile Owner's manual 6 2006, 354 |
Xtant Other A210 - TECHNICAL DATA REPORT#9T4S99 A210 - TECHNICAL DATA REPORT: Xtant Other Owner Documentation A210 - TECHNICAL DATA REPORT, 1 |
Digibell Intercom System Vandal Resistant SystemDigibell Vandal Resistant System Intercom System Installation & operation manual Vandal Resistant System, 56 |
Akura LCD TV APLDVD2021 W-HDIDAkura APLDVD2021 W-HDID Manual (Doc Type: LCD TV Quick start manual) APLDVD2021 W-HDID, 2 |
Haier Air Conditioner HDU-42CA03T3Air Conditioner Operation & installation manual (Haier HDU-42CA03T3) HDU-42CA03T3, 32 |
Parkside Soldering Gun PLS 48 A1#1W9M15: PLS 48 A1 Soldering Gun Operation and safety notes PLS 48 A1, 36 |
Baxi Indoor Fireplace Bermuda GF3Guide: Baxi Bermuda GF3 (FFX4B5, Upd.20.11.2023) Bermuda GF3, 8 |
Polycom Telephone VVX400-410PDF User Guide (@8R8YJZ), Polycom VVX400-410 Telephone (26.12.2023) VVX400-410, 11 |
Vent-a-Hood Ventilation Hood ZTHInstallation instructions manual for Vent-a-Hood ZTH Ventilation Hood ZTH, 6 |