Eachine M80 Instruction Manual

Text of Eachine M80 User Guide:

• Eachine M80, WARNING Please read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not i

• Eachine M80, control. • Always operate your model in open spaces away from full-size vehicles, traffic and people. • Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.). • Always keep all chemicals, small parts and anything electrical out of the reach of children. • Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics. • Never place any portion of the model in your mouth as

• Eachine M80,  Battery-500mAh 1S 3.8V 25C LiHV x1  Charger-1S USB Li-Po Charger x1  Transmitter x1  25MW VTX 600TVL FPV Camera x1 SPECIFICATIONS  Length: 100mm (3.94in)  Width ： 100mm （ 3.94in ）  Height: 50mm (1.97in)  Propeller Diameter: 40mm (1.57in)  Flying Weight: 52g (1.83oz) First Flight Preparation • Remove and inspect contents • Begin charging the flight battery • Assemble the aircraft • Program your transmitter • Install the flight battery in the aircraft (once it has been fully charged) • Bind your transmitter • Familiarize yourself with the controls • Find a suitable area f

• Eachine M80,  NEVER LEAVE CHARGING BATTERIES UNATTENDED.  NEVER CHARGE BATTERIES OVERNIGHT.  Never charge damaged batteries. If the battery begins to swell during charging or use, discontinue immediately.  Always use the included battery and charger. Disconnect the battery after charging.  Charge batteries away from flammable materials in a well-ventilated area.  Never charge, transport, or store batteries in hot, cold, or very sunny places (recommended between 40–120° F or 5–49° C). Charge the Flight Battery CAUTION: Only use chargers specifically designed to charge the inc

• Eachine M80, Installing the Propellers Refer to the illustration for the proper motor rotation and propeller location. The propellers are press fit onto the motor shafts. Remove the propellers by pulling the center hub straight up away from the motor. Install the propellers by pressing the center hub over the motor shaft, being careful not to press it too far down on the shaft. The propeller and motor should spin freely when installed correctly. Installing the Transmitter Batteries (RTF) The LED indicator flashes and the transmitter beeps progressively faster as the battery voltage drops. Replace the transmitter

• Eachine M80, Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when the batteries are charged. Transmitter and Receiver Binding 1. Place the drone flat on the floor and then plug in the battery. Green light will briefly flash. 2. When the remote controller is off, press the binding key (upper left corner D) and then turn ON the remote controller (press the power button) release the binding

• Eachine M80, normally. Note: You do not need to do it again once the binding is successful. Power on the remote controller then connected to the battery. Transmitter Control (RTF) Mode A B C D E F G M1 One key Return /Air pressure mode Throttle (Up/Down) /Roll (left/Right) Throttle Trim /Root Trim Mode switch Pitch （ Front/Back ） /Yaw (Left rotation /Right rotation) Pith Trim /YAW Trim One key Invert M2 Pith （ Front/Back ） /Roll （ Left/Right ） Pitch Trim /Root Trim Throttle (Up/Down) /Yaw (Left rotation /Right rotation) Thrott

• Eachine M80, 2. Rotate the two sticks along its inner wall. The LED will turn solid and quit calibration mode after recording the maximum and minimum data of sticks successfully. Understanding the Primary Flight Controls If you are not familiar with the controls of your quadcopter, take a few minutes to familiarize yourself with them before attempting your first flight. Throttle Rudder Elevator Aileron

• Eachine M80, Flight Mode Selection Change flight modes by pressing different buttons on the transmitter. The quadcopter is in stability mode when first powered on. The active flight mode is indicated by the LEDs at bottom of the quadcopter. Mode LEDs Agility (button D with one click) Solid Red LED Stability (button D with two clicks) Solid Red and Green LEDs Altitude (button A) Solid Green LED • Agility mode: the quadcopter has no bank angle limits and will not return to level fight if the sticks are released. Use rates and expo to tune the performance according to your flying style. • Stability mode: t

• altitude. In some cases, you may need to make a few short “hops” to an altitude of just a few inches until you become familiar with the control inputs and trim settings required to maintain a steady hover and altitude. Hovering The quadcopter requires minor throttle adjustments to maintain its altitude in hover. Remember to keep these throttle adjustments as minimal as possi

• Eachine M80, NOTICE: Crash damage is not covered under warranty. Low Voltage Cutoff(LVC) Once the battery reaches 3V under load, the ESC will continuously lower power supplied to the motor until complete shutdown occurs. This helps prevent over- discharge of the Li-Po battery. Land immediately once the ESC activates LVC. Continuing to fly after LVC can damage the battery, cause a crash or both. Crash damage and batteries damaged due to over-discharge are not covered under warranty. Repeatedly flying the aircraft until LVC activates will dam

• chair. If you start to suffer from motion sickness while flying, lower your chin against your chest. Fly in open areas, away from people, trees, cars, and buildings. The range of the system can be impacted by any obstructions blocking your signal. It is normal to see break up in the video going behind trees and other obstacles. Available Frequencies (mHz):

• Eachine M80, Does not function and smells burnt after connecting the flight battery Flight battery connected with the wrong polarity Replace the 3-in-1 board. Connect the flight battery noting proper polarity LED on receiver flashes rapidly and quadcopter will not respond to transmitter (during binding) Transmitter too near aircraft during binding process Power off the transmitter. Move the transmitter a larger distance from the aircraft. Disconnect and reconnect the flight battery to the aircraft. Follow the binding instructions Bind switch or button was not held while transmitter was powered on P

• Eachine M80, quadcopter Flight battery or transmitter battery charge is too low Replace or recharge batteries Aircraft or transmitter is too close to large metal object, wireless source or another transmitter Move aircraft and transmitter to another location and attempt connecting again Crashes immediately upon lift-off or doesn’t lift off Propellers in wrong locations Make necessary adjustments Static in FPV feed Interference on chosen channel Change the video transmitter and receiver channel WARNING ALL INSTRUCTION AND PRECAUTIONS MUST

• Eachine M80, Failure to exercise care while using this product and comply with the following conditions and guidelines could result in product malfunction, excessive heat, fire, property damage, and ultimately injury. Lithium Ion batteries are not toys. For the purposes of this document Li-Ion, Li-Po or Li-Fe batteries will be described as "Batteries". Handling and Storage Never alter, puncture or impact Batteries or related components. Do not directly connect the terminals with metal objects. This will short-circuit Batteries, result

Related Products and Documents (Quadcopters):

Comparable Devices:

Similar Resources:

• Parrot ANAFI (3 pages) How to maintain the battery of the ANAFI? Your ANAFI's smart LiPo battery is an essential element of your drone: it can power it for a flight lasting 25 minutes. In this section, the PARROT.COM team provides some advice and tips to maintain and maximize its lifespan. What type of battery is fitted to ANAFI? ANAFI is equipped with a Lithium Polymer (L …

• Carrera RC CA XL (6 pages) Made in China, Shantou. Assembly and operating instructions 安装和使用说明 取扱説明書 조립과 작동 방법 Montaj ve işletme kılavuzu Инструкция по монтажу и эксплуатации Carrera RC Quadrocopter CA XL#  3 7 0 5 0 3 0 0 2 …

• KaiDeng K70 Sky Warrior (18 pages) 2.4 GHZ 6 AXIS R/C QUADCOPTER1.Four-Rotor design allows great speed and maneuverability for indoor and outdoor use.2.Built-in 6-axis Gyro ensures excellent stability.3.loading capacity up to 500g.4.Auto hover/Headless function/One key to return.5.360-degree 3-dimensional stunt and tumbling function.6.WIFI Photo/Video.7. 2MP camera Photo/Video.8. 5MP camer …

• Carrera RC 370503013 (32 pages) # 370503013  Carre ra RC Quadrocopter CRC X1# 370503014  Carre ra RC Quadrocopter PoliceAssemb ly and operating instructionsΟδηγίες συναρμολόγησης και λειτουργίας安装和使用说明 取扱説明書 조립과 작동 방법 Инструкция по монтажу и эксп� …

• Saturn Multirotors Titan-X 225 (7 pages) !Page!1!of!7!Saturn Titan-X 225mm Assembly Manual PB3D Creations | Created 10-1-2016 With everyone getting their hands on their Titan-X 225 we figured an assembly log is much needed. This read will take you through the steps of assembling the full frame with all 3D Accessories. *Please note, this is not a build log for electronics setup and layout but we w …

• Skyrc SPHINX (6 pages) RoHSWarranty and ServiceWe guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. During that period, we will repair or replace free of service charge for p …

Comments, Questions and Opinions: