Apogee V-2 Conversion Kit Instructions

Text of Apogee V-2 Conversion Kit User Guide:

• Apogee V-2 Conversion Kit, Page 1 Colorado Springs, Colorado USA web site: www.ApogeeRockets.com The V-2 Conversion kit is another ne product from: Kit #12111 Skill Level 4 Made in USA P/N Item Name Qty 10091 AT-24/3.75” 1 10128 AT-33/17.75 (LC) 1 12358 CBD-33mm ⅛” Plywood (single) 1 13016 Coupler AC-33 (single) 1 13031 CR-18/24 (single) 1 13301 CR-24/33 ⅛” Plywood (single) 2 13279 CR-33 V-2 (LC) 1 13056 ¼” Launch Lug 1 24043 Crimped Engine Hook 1 29520 300# Kevlar X 8 ft 1 29602 Clay Nose Wt (⅓ stick) {30 grams} 1 29624 Wood Screw Eyebolt Size 9 1 29116 24” Plastic chute 1 31114 Instruction Sheet A 1 31115 V-2 Launc

• Page 2 Skill Level 3: Average Skills Needed This conversion kit is designed for the Spacemonkey Models V-2/A4 plastic model kit. It allows the rocket to be own with 24mm diameter model rocket motors. Changing a static model into a ying model is called “plastic model conversion” (PMC) by the National Association of Rocketry (NAR). There is even a

• Apogee V-2 Conversion Kit, Page 3 insert the motor mount tube into the aft end of the body tube SO THE BACK RING IS RECESSED AT LEAST ¼ INCH (6.5mm) INSIDE THE END OF THE TUBE. Also, the engine hook should NOT be in line with the line on the tube. When the glue is dry, pass the shock cord back through the motor mount, so that it comes out the front end of the rocket. Step 6 - Take the red tube coupler and place it on the plastic “aft nozzle insert” from the Spacemonkey Models V-2 kit. Do not glue it. Make sure it is straight on the nozzle insert. Draw a line on the plastic with a pen- cil, and remove th

• Apogee V-2 Conversion Kit, Page 4 Step 12 - Screw and then glue the screw-eye into the wooden bulkhead disk using wood glue. Glue the assembly into one end of the red tube coupler. The disk should be just inside the end so that you can put glue llets on both sides of the disk. Al- low the glue to dry. Step 13 (Optional) - Using a hobby knife, cut a series of v-notches into the front end of the tube coupler from the previous step. Because the edge will bend inward and conform better to the inside of the nose cone, this will make a stronger glue joint when the coupler is installed into the nose cone in the next step. Step 14 - Place the clay nose weight into the front of the plastic nose co

• Apogee V-2 Conversion Kit, Page 5 Launch Supplies Needed To launch your rocket you will need the following supplies: • A model rocket launching system • Flame resistant recovery wadding • Recommended Rocket Engines: C11-3, D12-5 Rocket Preight A. Crumple and insert 5 sheets of recovery wadding into the body tube. B. Fold the parachute and insert it into the tube with the shock cord. C. Insert the rocket motor into the aft end of the rocket. D. Insert and secure the engine igniter as directed on the package the engines came with. Countdown and Launch Procedure Fly your rocket on a large eld that isn’t near any power lines, trees, or low ying aircraft; T

Related Products and Documents (Toy):

Comparable Devices:

Similar Resources:

• E sky HUNTER (60 pages) Notice d´Utilisation Gebruiksaanwijzing Bedienungsanleitung Operating Instructions HUNTERNo. 00 00 53RC Elektro-Doppelrotor-Helikopter RTF mit 2,4 GHz 4-Kanal FernsteuersenderElectric RC Double Rotor RTF Helicopter with 2.4-GHz 4-channel remote-control transmitterHélicoptère électrique RC double rotor prêt à voler avec radiocommande de 2,4 GHz à …

• Bontempi iGirl 24 6830 (16 pages) GE 687124 6830ElectronicRock Guitarwith light effects GB - OWNER’S MANUAL ................2 F - MANUEL D’ INSTRUCTIONS .... .4 D - BEDIENUNGSANLEITUNG ........6 E - LIBRO DE INSTRUCCIONES ......8 P - MANUAL DE INSTRUÇÕES .....10 I - MANUALE DI ISTRUZIONI .....12 …

• REVELL Ferrari 250 GTO (14 pages) Ferrari 250 GTO07395-0389  2007 BY REVELL GmbH & CO. KG PRINTED IN GERMANYFerrari 250 GTO Ferrari 250 GTODer Ferrari 250 GTO wurde 1961 in der Werkstatt von Sergio Scaglietti entworfen. Zielwar es, gemäß der Vorgaben von Enzo Ferrari, einen Gran Turismo auf Basis des 250GT Berlinetta Passo Corto (kurzer Radstand = SWB/short wheel base) zu schaffe …

• SIG SKYRAY (6 pages) PARTS INVENTORY We understand how anxious you are to get started building and flying your SKYRAY, but before you do, please take a few minutes to inventory the contents of this package. Inside the box you should find: One-Piece Sheet Balsa Wing Die-Cut Balsa Profile Fuselage Die-Cut Sheet Balsa Tail Surfaces Die-Cut Plywood Parts F …

• K'Nex Lincoln Logs Bicentennial Edition (2 pages) 6 #4 logincludes:comprends:incluye:56#1 log10#3 log#5 log13#8 log2#8 log82roof support1chimney#8 slatw/hook2CHECK US OUT ON THE WEB!HTTP://LINCOLNLOGS.KNEX.COMVENEZ NOUS RENDRE VISITE SUR LE WEB !VISITE NUESTRA PAGINA EN EL INTERNET !Most models can be built one at a time.Products and colors may vary.Les maquettes se construisent une par une.Les produits et …

• Faller LARGE MARQUEE (24 pages) Sa. Nr. 140 495 1GROSSES FESTZELTLARGE MARQUEEGRAND CHAPITEAUGROTE FEESTTENTArt. Nr. 140495Vor Beginn des Bastelns sollten Sie sich mit den Spritzlingen und der Anleitung vertraut machen.Sollte es einmal vorkommen, dass ein Teil im Bausatz fehlt, kreuzen Sie bitte das fehlende Teil inder Anleitung an und schicken Sie diese bitte an Fa. Gebr. FALLER GmbH, Abt …

Comments, Questions and Opinions: