Ametek SI1500 User And Installation Manual

Text of Ametek SI1500 User Guide:

• Ametek SI1500, 502893 issue 4.1 13 6.0 Set Up Options 6.0 Set Up Options 6.1 MAIN MENU OVERVIEW Menu Parameter Setting Range 0.1dP Set decimal point position. nnnnnnn. To nn.nnnnn 02.St Hi Set High Alarm 0099.9999 to -099.9999 03.St Lo Set Low Alarm 0099.9999 to -099.9999 04.St0db Set Relay Hysteresis Time 0.1 to 9,9 seconds 05SE AL Switch Relay On or OFF On / Off 06.bEEP Switch Audible Alarm On or OFF On / Off 07SE1 nP Select Display Measurement Mode See "Function" section 7.0 Hold Peak + Peak - Difference 08HoLdt Set Auto Hold Time 00 - 10 secs

• Ametek SI1500, 502893 issue 4.1 21 6.0 Set Up Options 6.0 Set Up Options (cont) 6.3.3 Calibrate the Maximum and Minimum 22ACAL H 1.000 H !.000 L 1000 H !.000 L 1000 01 dP SWITCH BETWEEN HIGH AND LOW CALIBRATION POSITIONS CALIBRATE HIGH POSITION (PROBE IN) SI1500: DP MAX COUNT=16383 H 16383 3 SECS TO SAVE CALIBRATION -BEEP SI1100: LVDT VOLTAGE UP T0 +10 H 10000 CALIBRATE LOW POSITION (PROBE OUT) SI1500: DP MAX COUNT=16383 L 0000 SI1100: LVDT VOLTAGE UP T0 -10 L -10000

• 502893 issue 4.1 6 4.0 General Description 4.0 General Description 4.1 OVERVIEW The SI1000 series of readouts provides a simple way of using Solartron transducers. All of the basic metrology functions are provided within this small robust instrument. 4.2 SPECIFICATION See the Product data Sheet 502892

• Ametek SI1500, 502893 issue 4.1 23 7.0 Functions 7.0 Functions 7:3 Peak Function 0 7 S E 1 n P P e a k P 1 .2 3 4 5 D IS P L A Y F O L L O W S P R O B E P R E S S T O A C T IV A T E 2 .3 4 5 6 D IS P L A Y S H O W S M A X P R O B E R E A D IN G R IG HT D I G IT P U LS E S P R E S S to R E S E T ** 1 .2 3 4 5 D IS P L A Y F O L L O W S P R O B E P ro b e = 1.2 3 4 5 P ro b e = 2 .3 4 5 6 P ro b e = 1.2 3 4 5 2 .3 4 5 6 D IS P L A Y S H O W S M A X P R O B E R E A D IN G R IG HT D I G IT P U LS E S P ro

• Ametek SI1500, 502893 issue 4.1 8 5.0 Display Panel and Connections (cont) 5.0 Display Panel and Connections 5.1.1 Layout of Rear Panel SI1500 7 RS232 and RS485 Connection 8 Analogue Outputs 4-20 mA or VOLT 9 Digital Probe (Orbit Input) 10 High/Middle/Low Alarm Output Zero Input Hold/Peak+/Peak-/Diff input 24 VDC Input 5.1.2 Layout of Rear Panel SI1300 7 RS232 and RS485 Connection 8 Analogue Inputs: 4-20 mA or VOLT 9 High/Middle/Low Alarm Output Zero Input Hold/Peak+/Peak-/Diff input 24 VDC Input

• 502893 issue 4.1 16 6.0 Set Up Options 6.0 Set Up Options (cont) 6.2 MENU SETUP DETAIL 01. dP nnnn.nnn nnnnn.nn nnn.nnnn 02.St Hi 0000.000 0000.000 0000.001 R 0000.000 03.St Lo 0000.000 0000.000 0000.001 R 0000.000 04.St0db 0.1 0.1 0.2 05SE AL On On OFF 06.bEEP On On OFF 07SE1 nP Hold Hold Peak - P 09.St CO rS-232 rS-232 RS-485 08Ho ldt 0 0 1

• Ametek SI1500, 502893 issue 4.1 15 6.0 Set Up Options 6.0 Set Up Options (cont) Menu Parameter Setting Range 17rEAL Show Real value (Probe absolute Reading) 18Unit Select Units mm / inches 19StAn9 Select calibration On / Off 20CAL HI Set Scale maximum Set the Display Maximum Reading 21CALLo Set scale minimum Set the Display Minimum Reading 22ACAL Set Calibration Calibrate

• Ametek SI1500, 502893 issue 4.1 Terms in this Manual WARNING statements identify conditions or practices that could result in personal injury or loss of life. CAUTION statements identify conditions or practices that could result in damage to the equipment or other property. Symbols in this Manual This symbol indicates where applicable cautionary or other information is to be found. Service Safety This equipment has been designed and tested to meet the requirements of the Low Voltage Directive (1997) and has been supplied in a safe

• 502893 issue 4.1 25 8.0 Communication Protocol (RS232 and RS485) 8.0 Communication Protocol (RS232 and RS485) Data Reading Input Format Command (2 Bytes) ID (2 Bytes) End Code (2 Bytes) >R XX 0D 0A Data Reading Output Format Command (2 Bytes) ID (2 Bytes) Range Lamps (1 Byte) Reading (8 Bytes) End Code (2 Bytes) <R XX < or = or> XXXXXXXX 0D 0A Example S

• Ametek SI1500, 502893 issue 4.1 4 3.0 Installation into a Panel 3.0 Installation into a Panel - Ensure that there is sufficient space behind the relevant instrument panel for the SI1000 and its cabling Cut out the panel aperture to the dimensions shown. Working from behind the panel, with the box fully located, fit the side brackets to the studs and slide them forward toward the panel until they lock into place. Screw the brackets to the panel.

• 502893 issue 4.1 5 3.0 Installation into a Panel (cont) 3.0 Installation into a Panel (cont) CAUTION: Do not over tighten the screws as this may damage the case of the instrument. WARNING: On installing or removing the SI1000, you must be aware of any hazardous equipment or materials in the vicinity. Make sure that any equipment into which the SI1000 system is t

• Ametek SI1500, 502893 issue 4.1 11 5.0 Display Panel and Connections 5.0 Display Panel and Connections (cont) 5.2 CONNECTION DETAILS - SI1300 18 14 9 1 R S48 5 R S 2 32 V olt s R E L A Y P O W E RIN P U TS 4- 20 m A IN P U TS 1013 1 +24V DC Power 2 0V DC Power 3 Relay Common 4 Relay High Limit 5 Relay OK limit 6 Relay Low Limit 7 Input Relay Common 8 Zero Input Relay 9 Hold Input Relay 10 Analogue Current IN+ 11 Analogue Current IN- 12 Analogue Voltage IN+ 13 Analogue Voltage IN- 14 RS232 TXD 1

• Ametek SI1500, 502893 issue 4.1 22 7.0 Functions 7.0 Functions 7:1 Zero Function The Zero position is remembered by the SI1000 series even after a power cycle To put the SI1000 readouts into absolute mode, find the probe true zero position (mid stroke for an LVDT) or fully out for a Digital Probe. Zero at this position. Use the Real Value Menu to find the probe true zero position this always displays the actual probe reading. 7:2 Hold Function 0 7 S E 1 n P H o ld 1 .2 3 4 5 D IS P LA Y F O L L O W S P R O B E P R E S S

• Ametek SI1500, 502893 issue 4.1 14 6.0 Set Up Options 6.0 Set Up Options (cont) Menu Parameter Setting Range 09.St CO Select RS232 or RS485 RS232 / RS485 10 bPS Set Communication protocol 4800 / 9600 / 38400 / 115200 Data Bits (8), Parity (None) Stop Bits (1) 11Addr Set Communication address 1 - 99 12StoUt Set Analogue Output Signal None / +10 to -10 / +5 to -5 / 0 to +10 / 0 to +5 / 4-20 mA 13H "Er Enable Zero Key See "Function" section 7.0 On / Off Zero Display Press 3s 14H 1 nP Enable Hold Key On / Off Hold Display Press 3s 15dir Set Direction Extend / Retract 16OFFD Set Offset or Preset On / Off Preset Display Press 3s

• Ametek SI1500, 502893 issue 4.1 24 7.0 Functions 7.0 Functions 7:4 Input Relays ZERO RELAY Close Zero Relay (PIN 8 and PIN 7) >100mS ZERO DISPLAY Release Relay HOLD PEAK-P PEAK-N DIFF MODE RELAY Select Mode Menu 7 Close Hold Relay (PIN 9 and PIN 7) SI1000 will activate HOLD or PEAK-P or PEAK-N or DIFF (as selected Menu 7) Right Display Digit will pulse SI1000 will remain in MODE all time relay closed Right Display Digit will pulse Release Relay SI1000 will remain on MODE until time set in Menu 8 elapsed Right Display Digit will pulse for this time. SI1100 LVDT SET UP The SI1100 has two potentiometers. GAIN and OFFSET These can be used to adjust the LVDT

• Ametek SI1500, 502893 issue 4.1 18 6.0 Set Up Options 6.0 Set Up Options (cont) 13H ZEr On On OFF 14H 1 nP On On OFF 15dir EHtEn EHtEn rEtrAct 16OFFD 0000.000 0000.000 0000.001 0000.000 17rEAL 4.321 18Unit nn nn Inch 19StAn9 On On OFF 20CAL HI Only if 18SAn9 = ON

• Ametek SI1500, 502893 issue 4.1 3 This equipment contains no user serviceable parts. This equipment must be returned to your Solartron dealer for any service and repair. The SI1000 is designed to be maintenance free. Contact with solvents should be avoided. Any attempt to dismantle any of the SI1000 will invalidate the warranty. The SI1000 series are precision instruments and should be handled with care. 2.0 Service and Repair 2.0 Service and Repair

• Ametek SI1500, 502893 issue 4.1 26 8.0 Communication Protocol (RS232 and RS485) 8.0 Communication Protocol (RS232 and RS485) Alarm High/Low Value Reading Output Format Command (2 Bytes) ID (2 Bytes) Alarm Hi/Low Data (17 Bytes) End Code (2 Bytes) >S XX XXXXXXXX,XXXXXXXX 0D 0A Example SI1500 Display High Alarm Value 0.500 Low Alarm value -0.005 To SI1500 “<S”,”01”,”=”,” chr$(13),chr$(10)” From SI1500 “>S”, “01”, “=” , “+000.500,-000.500”,chr$(13),chr$(10)

• Ametek SI1500, 502893 issue 4.1 9 5.0 Display Panel and Connections (cont) 5.0 Display Panel and Connections 5.1.3 Layout of Rear Panel SI1100 7 RS232 and RS485 Connection 8 Analogue Outputs: 4-20 mA or VOLT 9 LVDT Transducer Input 10 Transducer Zero Adjustment 11 Transducer Gain Adjustment 12 High/Middle/Low Alarm Output Zero Input Hold/Peak+/Peak-/Diff input 24 VDC Input

• Ametek SI1500, 502893 issue 4.1 19 6.0 Set Up Options 6.0 Set Up Options (cont) 6.3 CALIBRATION MENU 6.3.1 Set the Maximum Reading to the Maximum Sensor Output 20CAL HI 0000.000 0000.000 0000.001 0000.000 Set the Display to the maximum value for the Digital Probe Eg DP2 =2.0 Range 0099.999 to – 0099.999 Eg Set Max Value to 2 0002.000

• Ametek SI1500, 502893 issue 4.1 12 5.0 Display Panel and Connections 5.0 Display Panel and Connections (cont) 5.2 CONNECTION DETAILS - SI1100 18 1014 13 1 9 RS485 RS232 Volts 4-20mA OUTPUTS RELAY POWERINPUTS ZERO GAIN LVDT LVDT INPUT 1 +24V DC Power 2 0V DC Power 3 Relay Common 4 Relay High Limit 5 Relay OK limit 6 Relay Low Limit 7 Input Relay Common 8 Zero Input Relay 9 Hold Input Relay 10 Analogue Current + 11 Analogue Current - 12 Analogue Voltage + 13 Analogue Voltage - 14 RS232 TXD 15 RS232 RXD 16 RS232 GND 17 RS485 A(+) 18 RS485 B (-)

Related Products and Documents (Monitor):

Comparable Devices:

Similar Resources:

• NEC NP4000 (2 pages) © NEC Display Solutions, Ltd. 2007 Ver. 2 07/07 Printed in China Connect the projector. Schließen Sie den Projektor an. Connecter le projecteur. Connettere il proiettore. Conecte el proyector. Anslut projektorn. 󲴹󱂑󲁒󲥥󱆱 󱸥󰓥󲶞󰫽󰬙. Connect the supplied power cable (A). Press the main power switch (B). Schließen Sie das mit …

• Seiki SC151FS (1 pages) Coax Digital Output 1VGA Resolutions Supported640x480,720X400, 800x600, 1024x768, 1280 x 720, 1280 x 768, 1360 x 768 Headphone: Stereo Mini (3.5mm) 1RCA Output NARCA Input 1Audio Input for VGA 1Audio Connections 40GP' Container Unit Load w/o Pallet 1930Stereo Mini Phono Jack Input (3.5mm)NA 40HQ' Container Unit Load w/o Pallet 1932Audio Surround YE …

• Philips 190VW9FB (2 pages) PhilipsLCD widescreen monitor49 cm (19.1") wideWXGA+190VW9FBGreat value, best savings on widescreen displayThis Vista-ready 190VW9 delivers the simple, straight forward and reliable widescreen display performance you need without costly extras that strain your budget and without compromising on quality.Best Value for Money• Widescreen LCD displays m …

• HP L1950 (70 pages) 19" LCD Color Monitor HP L1950 1 Service Service Service Horizontal Frequency …

• ibis A500 (16 pages) IBISIBISA500 MINI MONITOR音箱使用说明书/OWNER’S MANUAL质保卡/ WARRANTY DOCUMENT购买登记卡/ REGISTRATION CARD英文版/GB Page1 - 6中文版/CHN 第 7-11 页 …

• GREISINGER GIA 0420 WK (18 pages) E41.0.X1.6C-06 GHM GROUP - Greisinger GHM Messtechnik GmbH | Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY Tel.: +49 9402 9383-0 | [email protected] | www.greisinger.de Installation and operating manual Universal display for 4-20 mA - transmitter ab Version 1.0 GIA 0420 VO(T) GIA 0420 WK(T) GIA 0420 M12(T)  Please read these instructions c …

Comments, Questions and Opinions: