Allwin G300C Operation & User’s Manual

Text of Allwin G300C User Guide:

• Allwin G300C, 5 1.2 Web UI Management The VoIP router provide user friendly Web interface to let you configure your router function and VoIP function. There are a help on line content within each setting page. Please press Help hyperlink to view the on line help. There are 3 main functions for web, VoIP, System Setup(Router) & System maintenance. Each function is setup by the function below: 1.2.1 Web UI Management Overview Route function z Connection (Setting WAN connecting) z LAN Setting z Firewall Basic setup z Networks System Status Display z Dynamic DNS Setting z DHCP Server Setting z Static Routing Setting z Local Se

• Allwin G300C, 63  Prompt voice for replace dial tone: Use a customize voice file to replace the dial tone  Warming Prompt after VoIP out failure: Annunciate a customize voice file when VoIP call failure.  No PSTN Line Connected : Annunciate a customize voice file when there is no trunk connected to the PSTN port and failure to call via PSTN line.  Can not register to server warming prompt : Annunciate a customize voice file when the gateway failure to register to Register Server.  Prompt voice for VoIP call in : When Remote gateway call in the gateway, if enable this function, the gateway will an

• 10 handle the router rule for hot line function. And please also remember to Strip 3 digits to stripe the “hl1” symbol and remember add real phone number you want to dial on Prefix. In this case, the setting example on call out routing (/VoIP Setup/Routing Setup/VoIP Call Out/) for hot line application is as below: Index Remark Area Code IP Address Strip Prefi

• Allwin G300C, 39 Please remember to press the modify button to take it effect. For store back to flash memory, please press Save Modification (/Syetem Maintenance/Save Modification/). Here is VoIP Routing Profile setting examples below: Index Name VAD CODEC H.245 Tunneling DTMF Relay T.38 FAX Relay Package Frame Q.931 Fast Start ID1 AS ID2 AS ID3 AS ID4 AS Delete 1 PF1 ON G.723.1 ON Out band ON 3 ON 00001 H.323 1001 E.164 Delete 2 PF2 ON G.723.1 ON In band ON 2 OFF 00002 H.323 1002 E.164 **** Password Delete When using profile PF1 , the parameters will be used for H.323 ID1 = 0001,

• Allwin G300C, 18 b. FirstDigitTime: Define the waiting time (seconds) for user press phone number first digit. User need to press first digits before the setting time (seconds) defined here, if VoIP Router wait for the defined seconds and there is no any digits press, the VoIP Router will stop to wait and feedback the user busy tone. c. OtherDigitTime: Define the waiting time (seconds) for user press phone number secondary & the rest digits. User need to press the rest digits before the seconds defined here, if VoIP Router wait for the defined seconds and there is no any digits

• Allwin G300C, 60 1.2.5.8 CDR /VoIP Setup/Advance Setup/CDR The Gateway can export all the CDR (Call detail Record) to external CDR server by HTTP protocol. The gateway supports up to 2 CDR servers for keep the record. z Export to CDR Server: Please install and enable this function if you want to keep CDR of this gateway. z CDR Server IP1: Please input the IP of first CDR server, if installed. z CDR Server IP2: Please input the IP of second CDR server, if installed.

• Allwin G300C, 74 Remote Log Settings Remote Log Check this file and the gateway will send the log message to the “Send Log to” remote host. Send Log to Set the IP address to send log. Email Log When the log buffer is full, the gateway will check whether this item is enabled. If enabled, the gateway will send all the log messages to the “Send Email to” email address. SMTP Server Set the SMTP Server (email server) to send the email log to. You can either specify the server’s name or its IP address.

• 34 1.2.2.8 VoIP Call In IVR Setting /VoIP Setup/Routing Setup/VoIP Call In IVR/ When Enable the [Prompt Voice for VoIP Call In function on /VoIP Setup/Advance Setup/Prompt Voice/ , all the remote party of VoIP caller will hear the customization upload voice file and need press the destination number. All the input number will be checked the number length and b

• Allwin G300C, 33 number will change to 104). When the line 1 user is going to have a tour to another location with same VoIP router equipment, user setup the called prefix number 601 forward to profile name CF1, and in CF1 profile, the Always field is set to hk.big.com/301, that mean any call number with prefix 601 will always be forward to another VoIP Router locate at hk.big.com and dial out number is 301. When the line 2 is busy and another VoIP with prefix 602 Call in, it will forward it to the assist.big.com with same number

• Allwin G300C, 54 z Silence Detection / Suppression: Enable or disable the Silence Detection/VAD function. When Enable, if local gateway detect a silence situation ( no talk), it will send a VAD package rather than a full voice package for remote side to active CNG ( Comfort Noise Generation) to save the bandwidth. The default is Enable to save the bandwidth. z Prefer CODEC : In this table, you can define the prefer CODEC. The priority 1 selection is highest priority. By different CODEC, user can select different payload si

• Allwin G300C, 28 range setting on /VoIP Setup/Routing Setup/Authorization/, if it is within the authorization, the gateway will allow the call out, but if the remote caller’s IP is not in the range, it will refuse to call out and terminate this call. Index Area Code Auth Strip Prefix MaximumMinimumFrom To LineNo RS Verify CallWaiting Alert Profile Forward Delete 1 8862 5 4 □ Delete c. Strip: Number of digits will be ignored by user input. For example, if received VoIP call number is 886212345678 and the STRIP field is setting to 4, the first 4 digits 8862 will be

• Allwin G300C, 55 1.2.5.4 RTP Packet Summary /VoIP Setup/Advance Setup/RTP Packet Summary On this page, user will know the RTP package summary about last VoIP call. z Line#: number of line z Using CODEC: ex.: G.723.1, G.729a z Source IP: Remote side IP z Source Port: Remote side port z Packet Interval: interval time between 2 packets.(ms) z Packet Send: number of packets sent. z Packet Received: number of packets received. z Packet Lost: number of lost packets.

• Allwin G300C, 61 1.2.5.9 FoIP /VoIP Setup/Advance Setup/FoIP User can define the parameters relative FAX Over IP function.  Maximum FoIP Rate (bps) Appoint the maximum FAX transceiver rate during FoIP:  Disable: Only the VoIP function is supported on the gateway. FoIP is disabled.  Auto: Gateway will negotiation the maximum speed for FoIP with FAX machine..  :Appoint the Maximum speed:2400,4800,9600,12000, 14000  T.38 Low Speed Redundancy: [Enable|Disable] Enable or Disable to send the double packet function during low speed T.

• Allwin G300C, 2 Table of contents Chapter 1 Web UI Management.......................................................................................... 4 1.1 Access to Web UI......................................................................................................... 4 1.2 Web UI Management..................................................................................................5 1.2.1 Web UI Management Overview.................................................................. 5 1.2.2.1 VoIP Setup/ Port Status/................................ 7 1.2.2.2 VoIP/Line Configure/ Line Sett

• Allwin G300C, 38  When select In band to transfer the DTMF during VoIP, the user pressed DTMF tone will be treat as general voice and been compressed then transmit to remote side to decompress play back, it maybe cause some problem on duplicate or missing DTMF receive.  When select Out band to transfer the DTMF during VoIP, the user pressed DTMF tone will be decode by local VoIP Router then transmit as signal, after received on received remote VoIP Router, it will be regenerate by remote VoIP Router. The default value is

• 8 i. Talking Sec: Total talked seconds of last VoIP call on this port. j. Dialed number:  On the VoIP call out (line status display “In”). This will display the real dial out number for VoIP call.  On the VoIP call in (line status display “Out”). This will display the number will dial out to phone line.  Release by: This will display the reason

• 90 Client Filtering Enable Client Filter Check this box and all the entries below will take effect. IP Block the IP addresses ranged to connect to Internet. Port Set the port range, within which is not allowed to connect to Internet. Type Set which protocol, TCP/IP/Both, of this entry to inhibit. Block Time Two options are provided for this column, the “Always” and “

• Allwin G300C, 52 1.2.5.2 Listen Port /VoIP Setup/Advance Setup/Listen Port In this page, user can define the usage port for setup the VoIP communication. Both side of gateways need use the same port for begin VoIP communication. a. SIP Listen Port : Define the listen port for SIP protocol, the default port is 5060, input range from 1024 to 65535. b. H.323 Call Signal Port: Define the Call signal port for H.323 protocol, the default port is 1720, input range from 1024 to 65535. c. .H.323 Gatekeeper Listen Port: Define the Gatekeeper listen port for H.323 protocol, the default port is 1719, input range from 1024 to 65

• Allwin G300C, 26 3 UseDefaultPF 3 Gate.proxy.com Delete Index Name VAD CODEC H.245 Tunneling DTMF Relay T.38 FAX Relay Package Frame Q.931 Fast Start ID1 AS ID2 AS ID3 AS ID4 AS Delete 1 PF1 ON G.723.1 ON Out band ON 3 ON 00001 H.323 1001 E.164 Delete 2 PF2 ON G.723.1 ON In band ON 3 OFF 00002 H.323 1002 E.164 Delete When VoIP call out number with prefix 1 will use the Profile named PF1 (H.323 ID1 = 0001, E.164 ID=1001, DTMF Relay=Out band, Q.931 Fas

• Allwin G300C, 91 URL Filtering Enable URL Filter Check this box and all the entries below will take effect. IP The IP addresses ranged will be the candidate to check the URL when they use web browser to access the Internet. URL filter string The specific URL string to block. Enable Check this item to enable this URL filter entry.

• Allwin G300C, 3 1.2.7.4 Administrator Setting .................................. 72 1.2.7.5 System Log ............................................ 73 1.2.8 Route Function(/System Setup) ...........................................................75 1.2.8.1 Setting WAN connection: System Setup/Connection ...75 1.2.8.2 LAN Settings .......................................... 80 1.2.8.3 NAT ................................................... 83 1.2.8.4 Firewall................................................ 88 1.

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• ZyXEL Communications AMG1202-T10A (12 pages) www.zyxel.comQuick Start GuideAMG1202-T10AWireless N-lite ADSL2+ 4-port Ethernet Gateway Firmware Version 1.00Edition 1, 2/2011DEFAULT LOGIN DETAILSLAN Port LAN1 ~ LAN4IP Address http://192.168.1.1Username adminPassword 1234 2011 ZyXEL Communications CorporationC …

• Alcatel-Lucent Service Aggregation Router 7705 (4 pages) Alcatel-Lucent 7705 Service Aggregation RouterInstallation, Provisioning, and Commissioning Checklist, Release 7.03HE 10325 AAAA TQZZA Edition 01December 2015OverviewThis checklist assumes you have read the applicable installation guide for your product and understand its procedures, including notes, warnings, cautions, and dangers.The “Installing, Provisi …

• Unimax MA-2025-4G (72 pages) Unimax Ethernet Modem Router MA-2025 | MA-2025-4GUser ManualThis manual is the sole and exclusive property of Maxon Australia.Not to be distributed or divulged without prior written agreement.Unimax 4G Ethernet Modem Router | MA-2025-4G+Unimax HSPA+ Ethernet Modem Router | MA-2025+ …

• Worx WU600 (26 pages) Router ENGФрезерная машина RUS Pag 06Pag 16WU600/WU600.1/WU601/WU601.1UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 1 2006-7-26 14:08:37 …

• D-Link DIR-868L (3 pages) Technical Support Setup Procedure Page 1 of 3 How to setup Repeater mode on DIR-868L (Ax)? Step 1: Connect your laptop or PC to the router by using a Network Cable. Step 2: Open a web browser such as Internet Explorer, Mozilla Firefox or Google Chrome. On the address bar of the web browser type in …

• Resol DeltaSol MX (48 pages) 48006450Vielen Dank für den Kauf dieses RESOL-Gerätes.Bitte lesen Sie diese Anleitung sorgfältig durch, um die Leistungsfähigkeit dieses Gerätes optimal nutzen zu können. Bitte bewahren Sie diese Anleitung sorgfältig auf.EM MontageAnschlussBedienungErweiterungsmodul für den Anschluss an die Systemregler DeltaSol® MX ode …

Comments, Questions and Opinions: