Manualios.com

AeroPlus Extra 330LT Manual 

AeroPlus Extra 330LT Manual Online:

3, 2231 votes
AeroPlus Extra 330LT User Manual
AeroPlus Extra 330LT User Guide
AeroPlus Extra 330LT Online Manual

Text of AeroPlus Extra 330LT User Guide:

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved Extra 330LT 85-125CC Item No:A-G120001 Specs: WING SPAN: 111” (2833mm) LENGTH: 100" (2530mm) WING AREA: 2139sq in (138sq dm) FLYING WEIGHT: 25.3-28lbs (11500-12800g) ENGINE: 100cc-120cc gas RADIO: 4CH/6-9S Description Covering Material Genuine Oracover Carbon Fibre: Spinner, wing tube and sleeves, landing gear, tail gear; Fibreglass servo arms, horn and reinforced U/C mounting Fiberglass servo arms and horn;

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 100-125CC Extra 330LT Congratulations on your purchase of your new AeroPlus RC Extra 330LT. This plane has been designed to be one of the lightest and highest performance aerobatics planes anywhere. We hope that you will enjoy this plane and will exceed your expectations in what a model airplane can be. Thank you, AeroPlus RC Unpacking - Carefully unpack the model, when opening the plastic bags make sure you do not to cut any covering on the model. Inspect each item to make sure there was no damage in shipping. If for any

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved Landing Gear Assembly  To help prevent the fuselage from being damaged while the model is being assembled we recommend fitting the landing gear first. Note - Before beginning assembly be sure to determine your left and right wheels pants.  First, glue the thin wood wheel spacer to the inside of the wheel pant on what will be the outer side of the pant. Use the bolt to help centre the spacer  Next, insert the bolt from what will be the ou

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved  Tighten down the bolt holding the locknut. Note – Do not over tighten. This will prevent the wheel from turning.  Insert the protruding bolts through the landing gear hole.  Tighten up using a washer and lock nut.  Repeat for other side.  This method takes time but is worth it as the wheel pants will last many flights. Horizontal Stab 1. Now glue the control horns into the e

  • www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved b. Before gluing the area on the horns that goes inside the elevator needs to be roughed up with sandpaper. This allows a better glue joint. c. Using Epoxy now glue the two control horns into their respective places. Note: it is highly recommended t

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved c. Next remove the servo and use thin C.A. glue to reinforce the threads. After the glue is dry reinsert the servo. Note. Depending on servo arms used it may be necessary to install arm before reinstalling the servo. d. Next install the servo linkages. 3. Extensions a. Thread a 36” servo extension though the fuselage to the openings near the elevator.

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved b. Connect the servo to the extension but be sure to use a servo clip or a piece of heat shrink to ensure it does not become disconnected during flight. 4. Installing Elevator Halfs a. Install the small carbon tube into the fuselage. b. Slide the Elevator Half onto the tube. Note: make sure the servo wire goes cleanly inside the fuselage and is not pinched. c. Attached the elevator half to the fuselage with the provided hardware. M3×12 inner hexagon screw & M3 wrench 5. Repeat the process for the

  • www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved Rudder 1. Remove the covering where the rudder horns push through with either a hobby knife or soldering iron. 2. Test fit the rudder horns Note: Be sure the rudder horns are equal on both sides and in line with the hinge point this is very important!

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 5. Glue the rudder horns in the rudder with epoxy; wipe off excess glue while it is wet. Note: Use the ball joint and bolt while gluing to maintain alignment. Note: While still movable measure that the same amount pushes out each side. Care needs to be taken here otherwise your rudder geometry will be incorrect. 6. Installing the Rudder Servo a. If using the included ruder arm assemble the rudder servo control arm as below, drill holes for screws and use C.A. glue to stop the nuts from coming loose. b. Fi

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved c. Using servo screws fix the servo in place, note the spline is towards the front of the plane. 7. Installing the rudder cables a. Thread the cables though the fuselage from the rudder to the servo tray b. Loop the cable though the crimp and attachment point as shown below. c. Crimp the cable using a pair of pliers then trim cable.

  • www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved d. Repeat this at the rudder end. Note: be sure the cables are taunt but not over tight. Tail Gear 1. Locate all parts in picture below, when assembling remember to use thread-lock on all parts 2. Assemble gear according to photograph.

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 4. Screw the tail gear to the fuselage with the three supplied bolts Wings and Ailerons 1. The ailerons on the wings are pre-glued. Check each one by gently pulling to make sure that they are secure 2. Installing aileron control horns a. Remove the covering where the aileron horns are glued in place. Use either a soldering iron or a sharp knife

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved b. Using sand paper rough the area that will be glued into the aileron. c. Glue both horns in with epoxy glue. Note: be sure to install a ball link to insure correct alignment when glueing d. Repeat for all 4 aileron control horns. 3. Install Aileron Servos a. First test fit the servo into the servo mount. Some trimming make be required. Note. Servo fits so spline is towards the front

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved b. Now pre drill the servo mounts with a 1/16 drill bit, then secure the servo into the servo mount with servo hardware. c. Next remove the servo and use thin C.A. glue to reinforce the threads. After the glue is dry reinsert the servo. d. If required install a servo extension lead onto the servo, remember to use a servo plug clip or heat shrink

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved e. Fit the servo. f. Using the supplied pushrod screw a ball-link onto each end. g. Using the supplied bolts attach the pushrod at both ends. Check to see you have sufficient movement of the aileron. If not adjust. h. Repeat on other wing Note: On wings using two servos be sure the servos are not binding. If the are you make have to adjust linkages or use a product such as a match box

  • www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved Gas Engine installation 1. Using the template that came with your chosen engine, check the diameter of the required bolts and drill accordingly. 2. mount the engine with the stand offs to the bulkhead. Remember to use large washers on the inside to spread

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 4. Cutting cowl for exhaust and airflow. Mark the area needed to be removed and cut out using a rotary cutting tool. a. You will need to cut the cowl accordingly to clear your chosen exhaust. Remember to start wholes small and work them until it fits. b. To make sure the engine stays cool. Ensure that enough air can get out of the cowl. The ration is usually 3 to 1. With the exit being 3 times larger then the intake. 5. Attach gas proof tube such as Tygon according to the labelling on tank

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 6. Use the supplied pushrod with a ball joint to connect to the throttle arm on the engine. Then find a convenient place to locate the throttle servo using the supplied mount. 7. Install the engine box cover plate once all connections have been made for the engine. 8. Mount the engines ignition to the motor box on radio foam to reduce vibrations.

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved 9. Radio Gear 1. On each side of the fuselage near the canopy bolts are areas for switches to be mounted. 2. A convenient place to mount the RX is just in front of the rudder servo. Ensure that it is mounted on Velcro or radio foam and securely strapped down. Canopy Attachment 3. The canopy is held in place with the 4 screws, ensure these are tight befo

  • AeroPlus Extra 330LT, www.aeroplusrc.com [email protected] AeroPlus RC Copyright 2014 © All Rights Reserved Before you fly! We highly recommend the use of both dual rates and exponential. This will allow the model to fly both precision and 3D at the flick of a switch. Suggested Set up Low Rates Exponential High Rate Exponential Elevator 15-20 deg 15-20 % 35-45 deg 30-60 % Ailerons 15-20 deg 15-20 % 35-45 deg 30-60 % Rudder 25-30 deg 15-20 % 35-45 deg 30-60 % For your maiden flights always use low rates, Also please reme

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 PS Audio POWERPACK 1500 MKII Quick start manual ps-audio/powerpack-1500-mkii-F18.pdf 21 Nov 2023 2
2 Vox MINI3 Owner's manual vox/mini3-LZ1.pdf 11 Jan 2024 16 0.55 Mb
3 Transition Networks TNIC-1500-AF Manual  transition-networks/tnic-1500-af-SI7.pdf 17 Feb 2024 16 0.17 Mb
4 HP Surestore 64 - Director Switch Planning manual hp/surestore-64-director-switch-2GU.pdf 30 Aug 2023 172 2.57 Mb
5 Samsung SRS579NP Operation & user’s manual samsung/srs579np-697.pdf 01 Aug 2022 32 1.42 Mb
6 Kenmore KENMORE 385.1915 Owner's manual sears/kenmore-385-1915-569.pdf 27 Jan 2024 108 9.46 Mb

Similar Resources:

  • Enabling Devices

    Flip Flop 503

    (2 pages)
    Fig. 1Fig. 1Fig. 1Fig. 1 Fig. 2Fig. 2Fig. 2Fig. 2 For Technical Support:For Technical Support:For Technical Support:For Technical Support: Call our Technical Service Department Monday through Friday, 9 a.m. to 5 p.m. (EST) 1-800-832-8697 [email protected] Flip Flop #503 USER’S GUIDE …
  • GLD Products

    Orion

    (48 pages)
    Orion DartboardItem 42-1036ORION ELECTRONIC DARTBOARDReplacement PartsOrder direct at www.gldproducts.com or call our Customer Service department at(800) 225-75938 am to 4:30 pm Central Standard TimePublication 42-1036 Rev BApril 2016 UPC Code 7-19265-54414-2 …
  • Eduard

    32 764

    (2 pages)
    32 764ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITeduard1/232 764REMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM1C …
  • Fisher-Price

    R6302

    (4 pages)
    Please keep this instruction sheet for future reference, Please keep this instruction sheet for future reference, as it contains important information.as it contains important information.Requires four “AAA” (LR03) Requires four “AAA” (LR03) alkalinealkaline batteries (not included) for operation. batteries (not included) for operation.Adult assembly …
  • Fisher-Price

    Press & Go C0129

    (4 pages)
    www.fisher-price.comC0129, C6517InstructionsPress & Go™TrainPlease keep this instruction sheet for future reference,as it contains important information.Requires three "AA" batteries (included).Adult assembly is required for battery replacement.Tool required for battery replacement:Phillips screwdriver (not included). …
  • Eduard

    Zoom Su-25UB/UBK seatbelts STEEL 1/48

    (2 pages)
    FE8361/2FE836detail set for 1/48 SMĚR kit • sada detailů pro stavebnici 1/48 SMĚRORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND …

Comments, Questions and Opinions: