aero-naut Foxx Manual 

Text of aero-naut Foxx User Guide:

• aero-naut Foxx, FOXX is a powerful pylon racer. Building materials are mostly balsa and light-ply to achieve a light yet strong structure for maximum flying performance. Due to its considerable top speed this model is recommended for experienced pilots only. We use mostly laser-cut parts for maximum precision and to speed up the building process. Wing spars are spruce with sheet webs at the wing root for additional strength. Power is provided by suitable inrunners with a diameter of 28 mm. Construction should be according to the step-by-step instructions provided in this manual. Use the parts list to identify the included stripwood and hardware. Always check that parts fit perfectly and correct,

• FOXX is a powerful pylon racer. Building materials are mostly balsa and light-ply to achieve a light yet strong structure for maximum flying performance. Due to its considerable top speed this model is recommended for experienced pilots only. We use mostly laser-cut parts for maximum precision and to speed up the building process. Wing spars are spruce with sheet webs at the wing ro

• Chamfer lower edge of former R 6 to match installed positon behind former R 5 and temporarily insert in slots in right fuselage side behind R 5. Glue R 9 at an angle of 90° to servo tray R 8. Temporarily insert R 8/R 9 in slots in rigth fuselage side below R 6. Insert R 7 in slot at rear end of R 10. 3 Position left fuselage side R 2 onto tabs of formers and check for proper fit. Then rem

• aero-naut Foxx, Chamfer lower edge of former R 6 to match installed positon behind former R 5 and temporarily insert in slots in right fuselage side behind R 5. Glue R 9 at an angle of 90° to servo tray R 8. Temporarily insert R 8/R 9 in slots in rigth fuselage side below R 6. Insert R 7 in slot at rear end of R 10. 3 Position left fuselage side R 2 onto tabs of formers and check for proper fit. Then remove left fuselage side from formers. Glue in place wing mount R 7, apply glue to formers R 4, R 5 and glue left fuselage side in place. Secure fuselage with suitable weight until glue has c

• aero-naut Foxx, 12 mm from the top drill rear end of fuselage with 2 mm for elevator control. Insert snake inner R 19 through rear end of fuselage and through horizontal slot in former R 9. Apply glue to pushrod housing at rear end of fuselage only and cut off flush with fuselage. Do not apply glue to slot in former R 9! 7 Install elevator servo in servo tray and drill mounting holes for servo. Install pushrod connector R 25 to servo horn and install servo. Note that servo horn faces forward in installed position. This will enable you to adjust pushrod or r

• aero-naut Foxx, 12 mm from the top drill rear end of fuselage with 2 mm for elevator control. Insert snake inner R 19 through rear end of fuselage and through horizontal slot in former R 9. Apply glue to pushrod housing at rear end of fuselage only and cut off flush with fuselage. Do not apply glue to slot in former R 9! 7 Install elevator servo in servo tray and drill mounting holes for servo. Install pushrod connector R 25 to servo horn and install servo. Note that servo horn faces forward in installed position. This will enable you to adjust pushrod or remove servo horn through opening in former R 6. 8 Carefully

• aero-naut Foxx, Carefully sand fuselage and round off the edges. With a razor saw cut out canopy along the lines indicated on fuselage sides. cut here cut here 11 Glue together fin parts R 14 and R 15. R 16 is added to fin after model has been covered. 12 Bevel off front edge of elevator R 13 to allow for sufficient control throw, then glue in place control horn R 17. Attention: Note orientation of control horn. The vertical edge faces aft! When dry, sand front edge of control horn flush with front edge of elevator. 13 14 Glue fin in place on tailplane R 12 and make sure fin is at an angle of 90° in re

• aero-naut Foxx, Carefully sand fuselage and round off the edges. With a razor saw cut out canopy along the lines indicated on fuselage sides. cut here cut here 11 Glue together fin parts R 14 and R 15. R 16 is added to fin after model has been covered. 12 Bevel off front edge of elevator R 13 to allow for sufficient control throw, then glue in place control horn R 17. Attention: Note orientation of control horn. The vertical edge faces aft! When dry, sand front edge of control horn flush with front edge of elevator. 13 14 Glue fin in place on tailplane R 12 and make sure fin is at an angle of 90°

• aero-naut Foxx, F 1 A F 1 A F 1 A F 1 A F 1 Fit together the two-piece wing jig and secure to building board with tape. 15 Glue together two centre ribs F 1. Then insert ribs F 1 to F 10 into jig. If necessary, tack-glue tabs to building bord with a drop of glue to secure ribs. 16 Glue in place upper wing spar 11 (5×2 mm spruce). Make sure all ribs are upright and fully seated in jig. Glue leading edges F 12 (4×4 mm obechi) to front of ribs. Insert pins in front of leading edes into jig to hold leading edges in position. 17 Glue riblets F 1 A to centre ribs F 1, two riblets either side. 18 F 1 F 10 F 11 F 12

• aero-naut Foxx, F 1 A F 1 A F 1 A F 1 A F 1 Fit together the two-piece wing jig and secure to building board with tape. 15 Glue together two centre ribs F 1. Then insert ribs F 1 to F 10 into jig. If necessary, tack-glue tabs to building bord with a drop of glue to secure ribs. 16 Glue in place upper wing spar 11 (5×2 mm spruce). Make sure all ribs are upright and fully seated in jig. Glue leading edges F 12 (4×4 mm obechi) to front of ribs. Insert pins in front of leading edes into jig to hold leading edges in position. 17 Glue riblets F 1 A to centre ribs F 1, two riblet

• aero-naut Foxx, Glue in place top wing sheeting panels F 13 and F 14 (1.5 mm balsa). Fit and glue in place F 13 first. Attention: The rear end of F 13 must coincide with centre line of wing spar. Remove residual glue immediately to provide a good contact surface for F 14. Fit and glue in place webs V 1 to V 3 between ribs F 1 to F 4. Glue in place lower wing spar F 11 (5×2 mm spruce). Glue servo trays F 15 in rib bays between ribs F 3 and F 4 to upper spruce spar and to top sheeting. Align servos parallel with rear edge of wing and glue in place on servo trays. 19 21 When glue has completely dried, carefully r

• aero-naut Foxx, Glue in place top wing sheeting panels F 13 and F 14 (1.5 mm balsa). Fit and glue in place F 13 first. Attention: The rear end of F 13 must coincide with centre line of wing spar. Remove residual glue immediately to provide a good contact surface for F 14. Fit and glue in place webs V 1 to V 3 between ribs F 1 to F 4. Glue in place lower wing spar F 11 (5×2 mm spruce). Glue servo trays F 15 in rib bays between ribs F 3 and F 4 to upper spruce spar and to top sheeting. Align servos parallel with rear edge of wing and glue in place on servo trays. 19 21 When glue has completely dried, carefully remove wing from jig and turn upside down. Cut off tabs w

• aero-naut Foxx, Carefully sand rear edge of wings flush with ribs. Trial-fit trailing edges F 16 and cut contact surfaces at wing centre to appropriate angle. Then glue trailing edges in place and secure with tape. Carefully sand top and bottom wing sheeting flush with end ribs. Wing tips consist of 4 pieces F 17 each. Glue together, then glue to end ribs. When dry, sand wing tips and leading edge to shape and give complete wing a smooth surface. 23 Position wing on fuselage and align centre lines of wing and fuselage. Drill with 4 mm through wing and R 7 for M4 wing bolt F 19. Redrill R 7 with 5 mm. From below insert nut R 24 in R 7 and glue in plac

• aero-naut Foxx, Carefully sand rear edge of wings flush with ribs. Trial-fit trailing edges F 16 and cut contact surfaces at wing centre to appropriate angle. Then glue trailing edges in place and secure with tape. Carefully sand top and bottom wing sheeting flush with end ribs. Wing tips consist of 4 pieces F 17 each. Glue together, then glue to end ribs. When dry, sand wing tips and leading edge to shape and give complete wing a smooth surface. 23 Position wing on fuselage and align centre lines of wing an

• 48 - 50 mm With soft pencil mark ailerons on trailing edge: aileron cut-outs start 50 mm from centre line of wing. They are 210 mm long and 18 mm deep. Cut out ailerons with modeller´s knife and razor saw. 27 Bevel off front edge of ailerons to provide for sufficient control throw. Cut slots for control horns F 20 into ailerons and glue control horns in place. Attention: If you use Z-bends

• aero-naut Foxx, 48 - 50 mm With soft pencil mark ailerons on trailing edge: aileron cut-outs start 50 mm from centre line of wing. They are 210 mm long and 18 mm deep. Cut out ailerons with modeller´s knife and razor saw. 27 Bevel off front edge of ailerons to provide for sufficient control throw. Cut slots for control horns F 20 into ailerons and glue control horns in place. Attention: If you use Z-bends on both ends of control linkage, glue control horns in place after ailerons have been attched to wing! Give the whole model a final sanding and cover it with the covering material of your choice. Use bright and contrasting colours on top and bottom of wing. This makes it easier

• aero-naut Foxx, No. Item Pieces Material Laserplatte Type Dimensions R 1 right fuselage side 1 balsa 1 laser cut 3 mm R 2 left fuselage side 1 balsa 2 laser cut 3 mm R 3 A motor mount (inrunner) 1 light ply 8 laser cut 3 mm R 3 B motor mount (outrunner) 1 light ply 8 laser cut 3 mm R 4 former 1 light ply 8 laser cut 3 mm R 5 former 1 light ply 8 laser cut 3 mm R 6 former 1 light ply 8 laser cut 3 mm R 7 wing mount 1 light ply 8 laser cut 3 mm R 8 servo tray 1 light ply 8 laser cut 3 mm R 9 elevator control linkage support 1 light ply 8 laser cut 3 mm R 10 wing support 2 balsa 1, 2 laser cut 3 mm R 11 A motor mount cover (inrunner) 1 birch ply 9 lase

• No. Item Pieces Material Laserplatte Type Dimensions R 1 right fuselage side 1 balsa 1 laser cut 3 mm R 2 left fuselage side 1 balsa 2 laser cut 3 mm R 3 A motor mount (inrunner) 1 light ply 8 laser cut 3 mm R 3 B motor mount (outrunner) 1 light ply 8 laser cut 3 mm R 4 former 1 light ply 8 laser cut 3 mm R 5 former 1 light ply 8 laser cut 3 mm R 6 former 1 light ply 8 laser

• aero-naut Foxx, and many more at www.aero-naut.com aero-naut Modellbau Stuttgarter Strasse 18-22 D-72766 Reutlingen www.aero-naut.de aero naut 1351/00-E1-09/2017 More great kits from our range... Luscombe Silvaire 1369/00 Lasercut kit Triple speed 1128/00 Triple R.E.S. 1128/01 Triple thermic 1128/02

Related Products and Documents (Toy):

Comparable Devices:

Similar Resources:

• HobbyKing 450 (31 pages) 0-@1ff{}fflj],HELICOPTERINSTRUCTIONMANUALii@1ftjjtBJH~-----'--Contents1_'0ASSEMBlYSECTOONIIllillll"SUVO'NSTUlAT,n.."••lt.12GYROINSUllAru}N'l'J'il1••Jiillll'.ilI!UUilll14CA..O"USEMI,yfllUlliUI15_22~"'RTSlIST.!'FIJI. …

• Fisher-Price DTM24 (4 pages) fisher-price.comDTM24Keep this instruction sheet for future reference, as it contains important information.Adult assembly is required. No tools required for assembly.Conserver ce mode d’emploi pour s’y référer en cas de besoin car il contient des informations importantes.Doit être assemblé par un adulte. Aucun outil nécessaire. …

• Faller Car System Digital (4 pages) Sa. Nr. 161 360 1CAR SYSTEM DIGITAL, EINZELSATELLIT, KLEINCAR SYSTEM DIGITAL, SINGLE SATELLITE, SMALL CAR SYSTEM DIGITAL, SATELLITE SIMPLE, PETIT CAR SYSTEEM DIGITAAL, LOSSE SATELLIET, SMALLArt. Nr. 161360Machen Sie sich bitte vor Beginn des Bastelns mit dem Bausatzinhalt und der Anleitung vertraut und prüfen Sie die Vollständigkeit. Im Reklamationsfall gi …

• Seagull Models SEA 285 (36 pages) 1Specications:Wingspan--------------- 80.0 in (203.2 cm).Wing area--------------- 957.9 sq.ins (61.8 sq.dm).Weight------------------- 13.7-14.1 lbs (6.2-6.4 kg).Length------------------- 58.8 in (147.2 cm).Engine/Motor size----- 0.46-0.55 cu.in 2stroke.Radio--------------------- 8 channels with 10 servos.ASSEMBLY MANUALCode : SEA 285 …

• SPIDERKITES Buddy (2 pages) Aufbau / AssemblyBefestigung der Flugleinen mit einem Buchtknoten / Flying line attachment with a larks head knot1. Stecke die Leitkantenstäbe in den oberen Verbinder.2. Der Buddy hat eine durchgehende Spreize, die mit einem Gummiring am Kielstab befestigt ist. Achte darauf, dass der Gummiring mittig zwischen den beiden Stoppern liegt.3. Setze die Quersprei …

• Multiplex RR FunGlider (48 pages) Anleitung 2 ... 9Instructions 10 ... 17Instructions 18 ... 29 Istruzione 30 ... 37Instrucciones 38 ... 4546 ... 47DFGBIES© Copyright by MULTIPLEX 2015 Version 1.0ErsatzteileReplacement partsPièces de rechangesParti di ricambioRepuestos AbbildungenIllustrationsIllustrationsIlunstrazioniIlustraciónes 23 ... 26# 26 4 …

Comments, Questions and Opinions: