Manualios.com

AEM 30-5500 Quick Start Manual

AEM 30-5500 Manual Online:

4.35, 2945 votes
AEM 30-5500 User Manual
AEM 30-5500 User Guide
AEM 30-5500 Online Manual

Text of AEM 30-5500 User Guide:

  • AEM 30-5500, AEM Performance Electronics 2205 126th Street Unit A, Hawthorne, CA 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com Instruction Part Number: 10-5500-QS Document Build 2/8/2018 CAN DISPLAY DASH & LOGGER SYSTEM QUICK START GUIDE

  • AEM 30-5500, 2 Introduction The purpose of this Quick Start Guide is to provide an overview of the installation and setup of the CAN Display (CD) dash. This guide assumes that an AEM-supplied pre-configured layout file is to be used which greatly simplifies the setup process. If not using a pre-configured layout or choosing to make changes beyond what is covered beyond the scope of this guide, please refer to the full CD dash user manual located in Documents\AEM\DashDesign\Instructions. The document is installed as part of the software installation process. Software I

  • AEM 30-5500, 3 Figure 1 - Connecting CD dash to non-AEMnet devices requires that included power harness be used to supply power and ground to the dash. Red and black wires from power harness connector should be connected to switched, fused 12v power and ground, respectively. Figure 2 - Connecting CD dash to AEMnet devices with only a 2 wire interface requires that the included power harness be used to supply power and ground to the dash. Add the two CAN signal wires for a complete connection. Red and black wires from power harness co

  • 4 Figure 3 - Connecting CD dash to AEMnet devices that have four wires present in their AEMnet connector is "plug and play" because the transmit device is providing power, ground and CAN communications through their AEMnet connector. Included power harness should not be used.

  • AEM 30-5500, 5 Figure 4 - Connector Interfaces CD DASH PINOUT PIN WIRE COLOR FUNCTION NOTES 1 RED 12V POWER Connect to switched, f used +12v power source 2 BLACK GROUND Ensure good ground connection that isn't shared with high noise emitters such as ignition systems 3 WHITE AEMNET/PORT 1 CAN+ CAN+; ty pically reserv ed f or AEMnet dev ices; use twisted pair wiring to minimize signal noise 4 GREEN AEMNET/PORT 1 CAN- CAN-; typically reserv ed for AEMnet devices; use twisted pair wiring to minimiz

  • AEM 30-5500, 6 Figure 5 - CAN connector port pinouts PORT 1/AEMnet PORT 2 PIN WIRE COLOR FUNCTION PIN WIRE COLOR FUNCTION 1 WHITE Port 1/AEMnet CAN+ 1 SILVER Port 2 CAN+ 2 GREEN Port 1/AEMNet CAN- 2 BLACK Port 2 CAN- 3 RED +12v Pow er 4 BLACK Ground Communication Cables The CD dash comes in two primary versions: logging and non-logging. Logging CD dashes come with two USB comms cables: one sealed bulkhead cable and one standard cable. The bulkhead cable is to be permanently connected to the dash and mounted in an

  • AEM 30-5500, 7 NOT disconnect the USB cable before this message appears. When the USB cable is disconnected from the PC, the dash will reset and then display the loaded layout file. Figure 6 - Status bar in DashDesign softw are. Do NOT disconnect USB cable until OK to disconnect message is shown. Uploading Firmware It’s good practice to ensure that the CD dash is loaded with the latest firmware. To upload firmware to the dash, open DashDesign software, connect the CD dash to the PC using the USB comms cable - check that status bar is green and indicates that

  • AEM 30-5500, 8 Dash Interface Figure 7 - Dash Interfaces LEDs All LEDs are configured by going to Setup>Shift Lights and LEDs. Amber - No dedicated function. Is triggered by alarm channels only. Custom triggering criteria possible. Red - No dedicated function - is commonly used for MIL/CEL. Is triggered by alarm channels only. Custom triggering criteria possible. Shift Lights - LED color from left to right: green, green, amber, amber, blue, blue blue. To set up shift light, click on Auto Create Outputs in Shift Light Setup to launch Shift Light Wizard. o Output - Set to channel to be referenced. This i

  • AEM 30-5500, 9 Track Mapping VDM, GPS Module or Internal GPS An AEM Vehicle Dynamics Module (VDM; 30-2206) or GPS Module (30-2207) can be paired with a CD dash to provide GPS data for race track mapping and lap timing. The module is added to the Port 1/AEMnet network using the AEMnet connector "Y" in its cable – see Figure 8 and VDM/GPS Module instruction manual for full installation guidelines. Products with internal GPS capabilities like the CD-5 can be connected as shown in Figure 9. Figure 8 - Track Mapping with 30-2206 VDM or 30-2207 GPS Module

  • AEM 30-5500, 10 Figure 9 - Track Mapping with CD-5 with internal GPS If using the AEM 5 Gauge layout file, the GPS channels are already configured and no additional setup is necessary. To add GPS channels to a layout that doesn’t already have them, start by opening the desired layout file and then go Setup>Display, click on CAN Receive tab, select Port 1 and then click on Import CAN button. Locate the VDM/GPS Module dbc file, select either US or SI units and click Open. CAN Import window will open showing all channels available for import – leave all channels selected and click on Import. All VD

  • AEM 30-5500, 11 With track mapping configured, the race vehicle can be driven on track to collect GPS data. At the exact moment when crossing the start/finish line, the lap beacon button should be pressed and held momentarily until both the amber and red LEDs flash on the dash. The lap beacon button is an external input that must be added using the violet wire input. See Figure 4. The flashing LEDs indicate that the start/finish line GPS coordinates have been successfully set. Each time the vehicle crosses the start/finish line, a new lap will be counted and lap timer will reset – see below for defin

  • 12 AEM CAN Sensor Module An AEM 22 Channel CAN Sensor Module (30-2212) can be paired with a CD dash to provide analog, digital and frequency signals for display and logging. The module is added to the Port 1/AEMnet network using the AEMnet connector "Y" in its cable – see diagram. See CAN Sensor Module instruction manual for full installation guidelines. AEM has supp

  • 13 monitoring live data, note the voltage value when the throttle is completely closed and also when completely open. Assign the closed throttle voltage to 0 and the full open throttle voltage to 100. Data Logging If using logging version of CD dash, logging can be configured by going to Setup>Logging to open the Logging Setup window. Here, channels can be selected to b

More Instructions:

DOWNLOAD

Related Products and Documents (Monitor):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Kenwood DP-R6070 Instruction manual kenwood/dp-r6070-GM5.pdf 09 Sep 2023 20
2 Aztech GR7000 Operation & user’s manual aztech/gr7000-191.pdf 29 Jun 2022 47 2.28 Mb
3 Samsung TL500 Manual del usuario samsung/tl500-3N5.pdf 23 Dec 2022 129 9.81 Mb
4 Omega Engineering DPiTH-i8DH Quick start omega-engineering/dpith-i8dh-7U3.pdf 22 Feb 2023 2
5 Pro-Form PFTL98584 Operation & user’s manual proform/pftl98584-6YG.pdf 17 Dec 2023 22
6 AUDIO TELEX TX30 Datasheet audio-telex/tx30-YH4.pdf 05 Aug 2023 1 0.31 Mb

Similar Resources:

  • Epson

    7850p - PowerLite XGA LCD Projector

    (2 pages)
    SMProjection System Epson original LCD prism technologyProjection Method Front/rear/ceiling mountLCDSize 1.0"Driving method Epson Poly-silicon TFT Active MatrixPixel number 786,432 pixels x 3 (1024 x 768) LCDsNative resolution XGAAspect ratio 4:3 (supports 16:9; 5:4)Pixel arrangement StripeProjection LensType Manual zoom/focusF-number 1.7 to 2.3f-number …
  • ProHD

    DR-N17F

    (24 pages)
    Version: V1.0.0V03For Customer Use:Please read the Instruction Manual carefullyand retain this information for future reference.MULTI FORMAT LCD MONITORINSTRUCTIONSDT-N17F …
  • Dell

    P2421D

    (14 pages)
    24" LED Monitor Dell P2421D 1 Service Service Service Simplified …
  • Digilent

    PmodSSD

    (3 pages)
    1300 Henley Court Pullman, WA 99163 509.334.6306 www.digilentinc.com PmodSSD™ Reference Manual Revised May 24, 2016 This manual applies to the PmodSSD rev. A DOC#: 502-126 Copyright Digilent, Inc. All rights reserved. Other product and company names mentioned may be trademarks of their respective owners. Page 1 of 2 Overview The PmodSSD is a two-digi …
  • Marshall Electronics

    M-Lynx-15

    (13 pages)
    For more information, contact Marshall Electronics, Industrial Video & Security (800) 800-6608MarshallIndustrial Video/Security Div.Marshall Lynx LCD Universal MonitorsUser Manualwww.mars-cam.com …
  • BenQ

    PD3200U

    (3 pages)
    TROUBLESHOOTING Why did my monitor not pick up the input signal automatically? Most of BenQ monitors have the “Input Auto Switch” option. By enabling “Input Auto Switch”, your monitor automatically chooses the best active input source based on all the input devices currently connected to the monitor. For example, if your monitor is connected …

Comments, Questions and Opinions: