Manualios.com

3DHS 92 Edge 540 V2 ARF Assembly Manual

3DHS 92 Edge 540 V2 ARF Manual Online:

4.15, 500 votes
3DHS 92 Edge 540 V2 ARF User Manual
3DHS 92 Edge 540 V2 ARF User Guide
3DHS 92 Edge 540 V2 ARF Online Manual

Text of 3DHS 92 Edge 540 V2 ARF User Guide:

  • 2 Please take a few moments to read this instruction manual before beginning assembly. We have outlined a fast, clear and easy method to assemble this aircraft and familiarizing yourself with this process will aid in a quick, easy build. Please read the following paragraph before beginning assembly of your aircraft! THIS IS NOT A TOY! Serious i

  • 3 Items needed for completion: • Masking tape. • Hobby knife with #11 blades. • Thin and medium CA. We highly recommend Mercury M5T thin and M100XF medium formulas as well as the Mercury glue tips. • 30 minute epoxy. Pacer Z-poxy is a long time favorite. • Pacer Formula 560 Canopy Glue • Blue Loctite. • Electric drill with an assortment

  • 3DHS 92 Edge 540 V2 ARF, 4 Let’s get started! Wing assembly 1. Locate the 2 wing panels as well as the composite aileron control horns and base plates. Use a soldering iron or sharp hobby blade to remove the covering over the slots for the aileron horn and aileron servo mount as shown. Make sure you are doing this on the bottom of the wing and aileron!

  • 3DHS 92 Edge 540 V2 ARF, 5 2. Scuff the portion of the horn that will glue into the aileron and secure with 30 minute epoxy. Wipe away any excess glue with an alcohol soaked rag. Insert the ball link between the horns to ensure proper alignment while the glue dries. 3. Inspect the hinges and make sure that each hinge is seated properly. Adjust any hinge holes that are impeding movement. Remove all of the hinges from the wing and aileron. Mix a generous batch of 30 minute epoxy. Use a zip tie or an old pushrod to thoroughly coat and fill the hinge holes

  • 6 5. Secure a 12 inch servo extension to the aileron servo lead and install your aileron servo as shown with the output shaft oriented toward the leading edge of the wing. 6. Assemble the aileron linkage as shown and secure to the aileron horn assembly and servo arm with the provided 3mm bolts. Apply blue Loctite to all bolts!

  • 3DHS 92 Edge 540 V2 ARF, 7 7. Repeat this process for the other wing, then inspect them both for taut covering and any lifting seams that need attention with a hot iron or heat gun. Give a good tug on the aileron to make sure all is secure, then clean the wings with a soft cloth and Windex and set aside. Note, the wings mount to the fuselage with nylon wing bolts. Fuselage Assembly 8. Locate the carbon fiber landing gear and mounting bolt set in the hardware bag. Insert each bolt into a washer, through the carbon gear and fuselage and secure with a

  • 3DHS 92 Edge 540 V2 ARF, 8 9. Trial fit the landing gear cuffs to the carbon gear legs and mark their location. Remove the cuffs and apply a bead of Silicon based Goop glue completely around the gear leg as shown. Slide the cuffs into place and secure with tape until dry.

  • 3DHS 92 Edge 540 V2 ARF, 9 10. Locate the landing gear hardware pack with includes two axles, two locking nuts, two large washers, two wheels, four wheel collars, two wheel pants and four M3 bolts and blind nuts. Attach the axles to the landing gear with the locking nuts and large washers. Install one wheel collar, then wheel, then a second wheel collar. Test fit the wheel pant for proper wheel placement. Attach both the inside and outside wheel collars to center the wheel in the wheel pant. Now would be a good time to grind a flat spot in the axle to give the outer w

  • 3DHS 92 Edge 540 V2 ARF, 11 12. Locate the tail wheel assembly. Now is a good time to remove all bolts and fasteners in the assembly and apply blue Loctite to these fasteners. Locate the three holes in the rear of the fuselage for the M3 bolts. Fasten the tail wheel assembly as shown.

  • 12 13. Locate the rudder, rudder control horns and hardware. Prepare the rudder control horns as previously done with aileron control horns. NOTE: IT IS RECOMMENDED TO USE THE PULL-PULL RUDDER SERVO LOCATION FOR THE 92” EDGE V2! This is for weight and balance purposes. The rudder has two positions for the rudder control horns. Please note in the following picture.

  • 3DHS 92 Edge 540 V2 ARF, 13 14. Glue the control horns in the upper position with the same technique used for aileron control horns. Hinge rudder the same as the ailerons. 15. Locate the slots for the pull-pull cable exit and open with a sharp Xacto knife or soldering iron. Run the pull-pull cables through the fuselage. Note, the wires should cross inside the fuselage. Mount the rudder servo as show. Using the Extreme Flight 4 inch arm, tapped for M3. Assemble four ball links to the pull-pull ends, screwing into the ball links 1/3 of the way. This wil

  • 3DHS 92 Edge 540 V2 ARF, 15 16. The firewall of the Edge has laser scribed locations for mounting the DA 70. Drill at the correct location for your choice of power plant. If using an alternative motor/engine simply download the mounting template from the engine manufacturer's website and align with the centering marks on the firewall and drill the appropriate holes. Mount the DA 70 using EF’s Blazing Star DA 70 stand off.

  • 3DHS 92 Edge 540 V2 ARF, 16 17. Throttle servo may be mounted under the motor box as shown. 18. If using stock mufflers, it is recommend to remove the tunnel cover for additional airflow. Also open vents on the bottom of the fuselage.

  • 3DHS 92 Edge 540 V2 ARF, 17 19. Mount mufflers, cut cowl as needed for mufflers. Install EF’s 17 or 24 oz. Flowmaster fuel tank. Mount ignition on the top of the motor box as shown. Complete the engine installation with your preferred components. 20. The Xpwr 60 Brushless Electric Outrunner from Extreme Flight is also an excellent powerplant for the Edge, producing gobs of clean quiet power rivaling that of the DA-70. We sell a set of Blazing Star XL standoffs that make mounting the Xpwr 60 very easy. Below is a photo of the Xpwr 60 installed along with our recommended ESC,

  • 3DHS 92 Edge 540 V2 ARF, 19 21. When satisfied with motor or engine installation, mount the cowl using supplied M3 hardware installed through holes in the F1 former into blind nuts in the cowl. There is one additional cowl bolt on the bottom. Horizontal Stabilizers 22. Prepare and install the elevator control horns as previously done with the aileron control horns. Also install elevator hinges the same as the ailerons. Note, there are shorten hinges at the inboard location of the elevat

  • 22 Set up and Trimming The CG range for the 3DHS 92" Edge 540 V2 can be measured at the wing root and starts at 5.25 - 6 inch which closely correlates to the location of the wing tube. If you balance at the center of the wing tube for the first flight you will be safe. There is plenty of room on the battery tray to move your batteries or receiver batteries to achieve this CG

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Paxar Monarch Pathfinder Ultra Gold Operation & user’s manual paxar/monarch-pathfinder-ultra-gold-R33.pdf 22 Feb 2023 216 4.17 Mb
2 Carrier 38TDB Product data carrier/38tdb-376.pdf 27 Oct 2023 56
3 Fujitsu T2020 - LifeBook Tablet PC Bios manual fujitsu/t2020-lifebook-tablet-pc-183.pdf 13 Jun 2023 25 1.62 Mb
4 Fujitsu PRIMERGY RX500 S7 Operating manual fujitsu/primergy-rx500-s7-74H.pdf 17 Oct 2023 88 1.33 Mb
5 DeWalt D28715-XE Instruction manual dewalt/d28715-xe-1LU.pdf 02 Dec 2023 12
6 Samson CL8 Ower's manual samson/cl8-8L7.pdf 01 Jul 2023 8 0.79 Mb

Similar Resources:

  • protech

    AZURRO

    (24 pages)
    T0387version: 28/06/2004 • T0387WARNING ! This R/C kit and the model you will build is not a toy.LET OP ! Deze bouwdoos van eenradiobestuurd vliegtuig is geen speelgoed.ACHTUNG ! Ein Dieser Bausatzferngesteuertes Modell ist kein Spielzeug.ATTENTION ! Ce planeur R/C à assembler n’est pas un jouet.INSTRUCTION MANUAL • GEBRUIKSAANWIJZING • ANLEITUNG � …
  • REVELL

    1856

    (4 pages)
    If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to:Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85185610200), part number, description, your return address and phone number.Visit our website: www.revell.comRevell Inc Elk Gr …
  • Faller

    120297

    (8 pages)
    Sa. Nr. 120 297 1MODERNER AUFZUG MIT ANTRIEBSTEILENMODERN LIFT WITH DRIVE PARTS ASCENSEUR MODERNE AVEC PIÈCES D'ENTRAÎNEMENT MODERNE LIFT MET AANDRIJFONDERDELENArt. Nr. 120297Inhalt Spritzlinge Contents Sprues Contenu Moulages Inhoud Gietstukken11x21x151xMachen Sie sich bitte vor Beginn des Bastelns mit dem Bausatzinhalt und der Anleitung vertraut und …
  • Fisher-Price

    W2621

    (6 pages)
    W2621BLR98Please keep this instruction sheet for future reference, as it contains important information.Adult assembly is required.Required three AA batteries (included) for operation.Batteries included are for demonstration purposes only.Tool required for battery replacement: Phillips screwdriver (not included).fisher-price.comSit & PlayTummy TimeLay &a …
  • Aircraft Modelers Research

    Extra 300 Mid-Wing

    (21 pages)
    Congratulations on your purchase of this excellent almost-ready-to-fly R/CCongratulations on your purchase of this excellent almost-ready-to-fly R/Cmodel! This ARF adopts the latest 3D design features and emphasizes highperformance,light weight and fun. The plane is designed by professionalengineers and built by skilled craftsmen.Many of the parts are alread …
  • Eduard

    Tiger I Ausf.E early

    (6 pages)
    3 sets54E401/636 256Tiger I Ausf.E early36 2561/35 scale detail set for Zvezda kit • sada detailů pro model 1/35 ZvezdaORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDR …

Comments, Questions and Opinions: