Hitachi H 65SC Service Manual

Text of Hitachi H 65SC User Guide:

• --- 20 --- PARTS H 65SC : ALTERNATIVE PARTS ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 1 998-423 STOP LEVER 1 2 998-426 NEEDLE ROLLER 1 3 306-437 NYLOCK HEX. SOCKET HD. BOLT M8X30 6 4 998-424 SPRING CASE 1 5 956-975 LEVER SPRING 1 6 998-425 DAMPER (B) 1 7 957-152 FRONT COVER 1 8 956-958 STRIKER 1 9 944-927 L-RING 1 10 944-928 PISTON PIN 1 11 956-957 PISTON 1 12 944-918 PIN D5X15.8 2 13

• Hitachi H 65SC, --- 21 --- PARTS H 65SC ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 52 956-948 COUNTER GEAR 1 53 600-1VV BALL BEARING 6001VVCMPS2L 1 54 960-251 HEX. HD. TAPPING SCREW D5X65 2 55 956-764 SPECIAL WASHER 2 * 56 340-259G STATOR ASS’Y 115V 1 INCLUD.57,63 FOR USA * 56 340-259E STATOR ASS’Y 220V-230V 1 INCLUD.57,63 57 945-932 BRUSH TERMINAL 2 58 620-1DD BALL BEARING 6201DDCMPS2L 1 59 318-208 HOUSING ASS’Y 1 INCLUD.69,80 60 996-370 FAN 1 * 61 360-286U ARMATURE ASS’Y 115V 1 INCLUD.49,58,60,64 FOR USA * 61 360-286E ARMATURE ASS’Y 220V-230V 1 INCLUD.60 62 306-098 FAN GUIDE 1 63 VINYL TUBE(ID7XT0.25X20) 1 64 944-954 BE

• Hitachi H 65SC, --- 22 --- : ALTERNATIVE PARTS * PARTS H 65SC ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS * 96 996-438 VINYL TUBE (A) (I.D.7XT0.5X50) 3 FOR USA * 97 980-063 TERMINAL 1 * 97 992-810 TERMINAL 1 FOR HOL * 97 930-804 TERMINAL M4.0 (10 PCS.) 1 FOR USA 98 984-750 TAPPING SCREW (W/FLANGE) D4X16 2 99 960-266 CORD CLIP 1 * 100 940-778 CORD ARMOR D10.7 1 * 100 958-049 CORD ARMOR D8.2 1 101 987-707 SEAL LOCK HEX. SOCKET HD. BOLT M6X25 4 8 --- 99 Printed in Japan (990825 N) 601 944-962 COLD CHISEL 410MM (HEX. SHANK TYPE) 1 602 944-964 CUTTER

More Instructions:

	Hitachi H 65SC Instruction manual and safety instructions 14-07-2023 40	DOWNLOAD
	Hitachi H 65SC Instruction manual and safety instructions 27-07-2022 44	DOWNLOAD

Related Products and Documents (Tools):

Comparable Devices:

Similar Resources:

• Pop Pop Nut PNT800L-PC (25 pages) POP NUT™ Tool PNT800L-PC Maintenance Manual Shanghai Huiyu Electronics Technology Co., Ltd. Tel:+86-21-54721680 Fax:+86-21-54721681 Web: www.huiyutools.cn …

• ujk technology 102946 (12 pages) Professional Coping Sled AT&M: 16.03.2017Book Ref: 103833• Work safely, securely and achieve accurate results • Low friction base allows for smooth gliding cuts• 19mm Mitre bar suitable for Tee or plain slot, adjustable for zero play• Work pieces firmly held horizontally and vertically, eliminating kickback • Vertical clamp close to …

• STEELGREEN SG36 (16 pages) OPERATOR’S MANUAL IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state law …

• molex 207129 Series (9 pages) Tool Kit for CTX280 Receptacle Terminals: >2.0 - 3.0mm² metric, Type ISO wire Doc No: ATS-6381981HM Release Date: 12-29-09 UNCONTROLLED COPY Page 1 of 9 Revision: B Revision Date: 09-24-10 CONDUCTOR BRUSH STRIP LENGTH SEAM CONDUCTOR CRIMP CUT-OFF TAB BELL MOUTH BEND UP TWISTING ROLLING BEND DOWN WIRE INSULATION CRIMP ▲SEE NOTE Application Toolin …

• Leigh FMT PRO (2 pages) JIG ADJUSTMENTSFMT PRO Appendix II61Jig AdjustmentsA2-1 Clamp Plate The Clamp Plate is factory set square to the table ➀. However, this does not guarantee perfectly in-line joints. If your router shaft and bit are not perpendicular to the router sub-base and the Leigh Sub-Base, then the bit will not be square to the Jig Table (nor parallel to the Clamp Pl …

• Parkside PDS 30 A1 (36 pages) EXTENDABLE CEILING SUPPORT ROD PDS 30 A1 EXTENDABLE CEILING SUPPORT RODOperating instructions DECKENSTÜTZEBedienungsanleitung ÉTAIMode d’emploi PLAFONDSTEUNGebruiksaanwijzingIAN 353782_2010CV_353782_PDS30A1_LB6.indd 1-3 01.02.2021 09:17:24 …

Comments, Questions and Opinions: