Panasonic UD-794D Operation Manual
|
Panasonic UD-794D, 26 Please address any enquiries within the European Area to: Panasonic Industrial Europe GmbH (UK) Willoughby Road, Bracknell,Berks.,RG12 8FP. UNITED KINGDOM Tel: 01252 876292 Tel: 07836 617737
Operation Manual Operation ManualOperation Manual Operation Manual TLD IRRADIATOR TLD IRRADIATORTLD IRRADIATOR TLD IRRADIATOR MODEL MODEL MODEL MODEL UD UDUD UD- -- -794D 794D794D 794D 2011/12 Operation Manual Version 10.
Panasonic UD-794D, 7 7) Connect all Computer AC line cords to the AC outlet located on the back of UD-794. (Option for European Users – if used, please select and label the PC equipment carefully) 7) Close and lock the front door to the UD-794. 8) To turn on the UD-794, Select ON from the rear AC input, turn on the internal powere switch and finally turn the main keyswitch located on the top-right side of the irradiator clockwise. 9) Power on the Display monitor, and PC. Now start UD-794 program by clicking on the Irradiator program icon. The AC power ind
Panasonic UD-794D, 16 Unload Tray button - This function unloads tray into the changer. Stop button - This function stops current badge processing. Exit button - This function returns the operator back to the Main screen for normal system operation. MODE\READER CHECK\CHANGER TEST MENU The Magazine Changer will automatically load up to ten (10) magazine trays holding 50 badges each or 500 badges into the Irradiator. The MODE\READER CHECK\CHANGER TEST menu allows qualified personnel to perform maintenance and diagnostic tests on the Magazine Changer. The operator u
2 (Rear view) ① AC power input output panel Power SW , Equipment (UD-794) power SW AC Input AC 220V-240V 50/60Hz Fuse T6.3A AC Output (3port) AC 110V-120V 50/60Hz Fuse 3.15A Inside motor Fuse (1A) ② Parallel I/F cable for DIO board inserted in the PC extende
Panasonic UD-794D, 4 SPECIFICATIONS Badge Capacity 500 TLDs Cycle Time Dependent on Dose required. Applicable TLDs Panasonic UD-800 Series only Control Standard Desktop PC (please ask for recommendations) Power outlet AC 110V – 120V 50/60Hz 3port MAX current 3.15A Power outlets are intended for the UD-794’s controller PC, And Monitor . No other equipment should be attached to these Operating Temperature 5 - 35℃ 20 – 70%RH Power source AC 220V – 240V 50/60Hz Dimensions 1000 mm X 550mm X 1120 mm (W x D x H ) Weight Approx 220kg which in
20 This requires the TLD Reader to be calibrated relative to the PSDL or SSDL and the Irradiator exposure adjusted to this using the same reference TLDs. Please discuss with Panasonic in detail. For Reference - Automatic Internal Calculation of Source Decay: Current Dose Rate = ( Initial Dose Rate ) e - ( 0.693 t / T ) t = Elapsed time in Days. T = 1/2 life of
Panasonic UD-794D, 12 View\Reports screen shows badge processing results in a user-friendly screen. It shows results by tray. For example, the user can view tray 1 results by selecting “View Tray 1” button. Mode\Reader Check\Loader Test MENU The Mode\Reader Check\Loader Test Menu is the menu from which Irradiator irradiator mechanics functions are tested and other diagnostic functions can be invoked. The Mode\Reader Check\Loader Test Menu screen and its operation and function are explained below. Please do not operate without guidance from a Panasonic
Panasonic UD-794D, 21 Parameters MENU – Individual Dose Setting MENU This menu allows individual dose setting parameters for the selected tray to be modified by an operator. “Use Tray\Individual” toggle function is used to select tray dose exposure setting or individual dose exposure setting for each badge in the selected tray. “Load from File” button is used to retrieve a saved irradiation tray pattern. “Save to File As” button is used to save an irradiation tray pattern “Save” button is used to save to current param
Panasonic UD-794D, 10 After changes in exposure dosages and exposuere time, “Save” button saves the corrent configuration into the parameter file and “Cancel” button restores the original settings. When setting the exposure dose or time for each tray, there is a menu option which also allows the user to set individual exposure dose or exposure time value for each slot in the selected tray. This menu option is explained in detail in “Individual Dose Setting MENU” section. Calculation of Exposure Dose: Expose Dose = Exposure Rate x Desired Exposure Time + Travel Dose Example: Exposure Rate = 0.281 mSv/sec Desired Exposure Tim
Panasonic UD-794D, 13 Magazine Motor functions - Magazine Motor functions are used to test the Irradiator system magazine motor mechanics. The Magazine Motor functions are explained in detail in the Magazine Motor functions description. Slider Arm functions - Slider Arm functions are used to test the Irradiator system slider arm mechanics. The Slider Arm functions are explained in detail in the Magazine Motor function description. Number Code Reader functions – Number Code Reader functions are used to te
Please use this equipment correctly, observing all internal warning signs. This device contains a source of ionizing radiation and its operation is limited to qualified personnel in accordance with your licence and its regulations. It is intended for irradiation of Panasonic TLDs only. Indoor Use Only. Do not expose to rain, h
Panasonic UD-794D, 3 (AC power input output panel View) ① Main power SW ② AC inlet port AC 220V-240V 50/60Hz ③ main fuse Box T6.3A 2pieces ④ UD-794 power SW ⑤ Fuse for internal AC motor : 1A ⑥ Fuse for AC outlet : 3.15A ⑦ AC outlet port (3Port) for PC,Display-monitor. CAUTION AC 110V-120V total 3.15A Model No. IRRADIATOR2NCE TLD IRRADIATOR ① ② ③ ④ ⑤ ⑥ ⑦
Panasonic UD-794D, 14 Single Step Adv button - This function advances a magazine by single step(s) into the Irradiator. The number of steps from home appears in the step counter window to the right of this function. Single Step Rev button - This function reverses by single step(s) a magazine out of the Irradiator. The number of steps from home appears in the step counter window to the left of this function. Next Slot Adv button - This function advances a magazine by one full slot into the Irradiator. Prev Slot Rev button - This function reverses a magazine by one full slot out of the Irradiator. Mag Start indicator - Monitors the status of the magazine drive home (origi
Panasonic UD-794D, 24 A6 Errors An A6 error occurs when the microswitch does not turn on when the solenoid is energized, or when the microswitch does not turn off when the rotary solenoid is deenergized. An A6 error may be resolved by turning the IRRADIATOR off and then on. This error may also be resolved by removing any jammed dosimeters or a jammed magazine. The jamming may have occurred because of improper loading of a dosimeter in the magazine. This error may also be caused by failure of the solenoid or microswitch, in which case the solenoid or microswitch should be replaced. A7 Errors This type of error occurs when the door switch is turned off while the power switch is
6 3) Place the Personal computer system(Display monitor,Keyboard,mouse and PC with installed UD-794 Control software on top panel of UD-794. 4) Remove the cover of the PC. Verify that the boards in the PC expansion bus are properly inserted and seated in their slots. 5) Connect the National Instruments DIO I/F cable
Panasonic UD-794D, 25 blocking the path of the badge or failure of the badge sensor. This error may be corrected by following the troubleshooting suggestions given in B-Type Error General Trouble shooting section. M0 Errors An M0 error occurs as the magazine is advancing to the next slot if the timing sensor does not detect a signal within the specified time limit, even though the specified number of pulses were transferred to the pulse motor. Causes and troubleshooting guidance for this error are given in M-Type Error General Troubleshooting s
Panasonic UD-794D, 11 Figure 1 New Batch Figure 2 New Batch (example) Figure 3 Program Status Window Note: A new batch appears as a new sub-directory in the C:Drive under \UD794D\Data\. View MENU View menu has BadgeResults, StatusLog, Reports menu items. BadgeResults menu and Reports menu items are for displaying badge processing results and StatusLog menu item is for displaying event logs. View\BadgeResults MENU View\BadgeResults screen shows badge processing results. It shows time, tray number, slot number, badge number, type, error, dose exposure, dose exposure rate, and dose exposure time.
Panasonic UD-794D, 8 OPERATION The Irradiator Control Software utilises mouse driven function selection to control irradiator operation. If additional data input is required, the screen will direct you to enter the appropriate data. Data entry is checked for valid ranges and limits upon entry. Invalid input data will be ignored and the computer screen will direct you to enter data in a valid range. The program starts with the Panasonic Title screen, as shown below (Software versions may be different): The operator is prompted to enter the proper password and operator name. After a short delay, during which the motors are initialized, the main
Panasonic UD-794D, 23 List of Error Codes and Description A3 Changer not moved to next shelf error A5 Changer not fully loaded or returned error A6 Autochanger solenoid failure A – Automatic Magazine Changer A7 Unit door is open B0 Badge not pushed up error B1 Badge not pushed down error B – Badge Inserter B2 Badge not pushed down error M- Magazine Driver M0 Magazine not moved to next slot. N0 NCR lamp error N- Number Code Reader N2 NCR Parity error R- RS232C Interface R2 RS232 TX data ACK time out A-Type Error General Troubleshooting Each of the specific A-type errors discus
Panasonic UD-794D, 5 INSTALLATION 1) Carefully unpack all equipment and peripherals. 2) Read all instruction manuals and documentation supplied with the Irradiator system. This device contains a source of ionizing radiation Operation is limited to Qualified Personel Set equipment on the horizontal Level hard floor. Equipment side space see below figure Equpment side space area A: Left side and Right side space is minimum 20mm B: Rear panel space is minimum 100mm C: Top panel space is minimum 0mm A A B C
Panasonic UD-794D, TABLE OF CONTENTS Introduction......................................................................................................................................................1 Description.......................................................................................................................................................1 Specification………………………………………………………………………… ………….5 Installation........................................................................................................................................................6 Operation...........
Panasonic UD-794D, 17 MODE\READER CHECK MENU -- CHANGER TEST MENU Up/Down control - A toggle function which turns ON/OFF the shelf feeding drive (vertical drive) motor. In/Out control - A toggle function which turns ON/OFF the magazine drive (horizontal drive) motor. Magaginze Motor In button - Advances a magazine into the Irradiator Irradiator. Magaginze Motor Out button - Reverses a magazine back into the Magazine Changer. Changer Down button- Advances the shelf feeding mechanism to the next shelf. Changer U
Panasonic UD-794D, 22 Parameters MENU – RS232 Options MENU This menu allows RS232 option parameters to be modified by an operator for serial communication or printing through RS232. RS232 Communication ON If this option is selected, the IRRADIATOR will transmit data string using selected comm. port, baud rate, data bit, stop bit, parity, flow control and interface mode. RS232 Serial Print ON If this option is selected, the IRRADIATOR will print out data string using selected comm. port and baud rate. Basic Mode If this
Panasonic UD-794D, 1 INTRODUCTION This operation manual contains the information required to install, operate and test the Model IRRADIATOR Irradiator Automatic Irradiator. DESCRIPTION Model UD-794 is a fully automatic irradiator used for irradiation of Panasonic UD-800 Series TLD badges. The UD-794 will automatically irradiate 10 magazines of 50 TLD badges. Description of parts (Front view) ① Main key switch Insert the main key and turn clockwise ② AC power indicator light When power on then this light illuminate RED. ③ Left door panel A source enclosure exists in the interio
Panasonic UD-794D, 9 MAIN SCREEN The Main Screen is the screen which controls normal operation of the Irradiator Automatic Irradiator. After the operator has entered the operator password, entered their name, and pressed the OK key, the Main screen appears on the monitor, as shown below: 1) The operator uses the mouse to select the Unattenuated(High) or Attenuated(Low) dose. This is a function which toggles between high and low exposure. High exposure dose rate opens the attenuator shutter and low exposure dose rate closes the attenuator shutter. 2) An exposure time and/or an exposure dose are then entered for each tray or single input depending on “Dosages and Time Mode�
Panasonic UD-794D, 15 Single Step Down - Single steps the badge push-up mechanism down. . The number of steps to the home position is displayed in the step counter window to the left of this function. Overrun button - This function causes the badge push-up mechanism to travel to the number code read position or to the irradiate position. Origin button - This function causes the badge push-up mechanism to travel to the NCR position or the home position. Vert Home Position indicator - Monitors the status of the Home Position Sensor RSR1. When the badge push-up mechanism is at the home position, this sensor is logic 1. NCR Position Detect indicator - Moni
Panasonic UD-794D, 18 Parameters MENU -- SYSTEM PARAMETERS MENU This menu allows critical system operational parameters or data to be modified by an authorized manager. This menu is password protected by the highest (manager) level password. IMPORTANT NOTE: The Dose Rate functions, Set Unattenuated (High) Rate and Set Attenuated (Low) Rate are the calibrated dose rates of the CS-137 source for the high and low attenuation settings. The calibration date allows for real-time compensation for the radioactive decay of the Cs-137 source. These parameters are initially set by to the exact dose rate measured at the badge irradiation position by
Panasonic AJHPM110E - MEMORY CARD PORTABLE RECORDER/PLAYER Card Reader Operating instructions manual
AJHPM110E - MEMORY CARD PORTABLE RECORDER/PLAYER |
Panasonic AJ-PCD20E Card Reader Operating instructions manual
AJ-PCD20E |
Panasonic AJ-HPM110 Card Reader Brochure & specs
AJ-HPM110 |
Panasonic ZU-9PS Series Card Reader Operation manual
ZU-9PS Series |
Panasonic AJ-PCD35P Card Reader Operating instructions manual
AJ-PCD35P |
Panasonic LP-ABR11 Card Reader Setup and operation manual
LP-ABR11 |
ST X-NUCLEO-NFC05A1 NFC Card Reader Operation & user’s manual
X-NUCLEO-NFC05A1 NFC |
Panasonic AJ-PCD10E Card Reader Operating instructions manual
AJ-PCD10E |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | York | YHJD30 | User's information manual | york/yhjd30-786.pdf | 01 Dec 2023 | 4 | 0.64 Mb |
2 | Electrolux | EW30EW65GS - 30" E Dbl Wall Oven WAVETCH Conv | Product specifications | electrolux/ew30ew65gs-30-e-dbl-wall-oven-wavetch-conv-GOB.pdf | 23 Nov 2022 | 2 | 0.21 Mb |
3 | Dyson | DC05 | Assembling & installation instructions | dyson/dc05-3D9.pdf | 23 Jan 2023 | 10 | 3.85 Mb |
4 | Viking | FAXJ-1000 | Application note | viking/faxj-1000-O5L.pdf | 31 Jul 2023 | 3 | 0.2 Mb |
5 | Cisco | 851 | Manual | cisco/851-ZL9.pdf | 31 Jan 2024 | 108 | 2.08 Mb |
6 | Teac | DR-H300 | Owner's manual | teac/dr-h300-J13.pdf | 02 Sep 2022 | 136 | 3.45 Mb |
RodinBell
1 Shenzhen RodinBell Technology Co., Ltd. D-100 UHF RFID Desktop Reader User Manual V1.1
…
D-100(17 pages) |
Axema
Axema Access Control AB | Box 90215 | 120 23 Stockholm, Sweden | +46 (0)8-722 34 40 | [email protected] | www.axema.seReader VAKA A66 SOLO (offline)ManualUpdated 04/11/2021
…
VAKA A66 SOLO(9 pages) |
Siemens
ASM 456 interface module ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ SIMATIC Ident RFID systems ASM 456 interface module Operating Instructions 07/2015 J31069-D0162-U001-A6-7618 Introduction 1 De …
ASM 456(64 pages) |
Renkforce
Inbetriebnahme• Schalten Sie Ihren Computer ein und warten Sie bis das Betriebssystem vollständig gestartet ist.• Drücken Sie zum Öffnen der Kartenfachabdeckung leicht auf dieselbe und klappen Sie sie wie unten dargestellt entlang der Achse des Befestigungspunkts auf:• Schieben Sie die Speicherkarte unter Beachtung der korrekten Ausrichtung in da …
2111255(4 pages) |
Videx
66250240 - V2.0 - 31/10/18- 1 -4000 SeriesArt.4838 - Installation instructionsABCCDFig. 1 Front5PTECNCNOBSYSLF1LBTCBCOMP112+12GNDP2P3P4DIP-SWITCH 1 SETTINGS (8 way)MELODIES1,2RINGS3,4SPEECH TIME5,6DOOR OP. TIME7,8SWITCHES SETTINGSOFF OFFOFF ONONOFFON ONMELODY 1MELODY 2MELODY 3MELODY 42 RINGS4 RINGS6 RINGS8 RINGS30s60s90s120s1s4s8s16sDIP-SWITCH 2 SETTING …
4000 Series(12 pages) |
Dell
CACStar User Guide Rev A27 Copyright 2017 Digital Imaging Technology Page 1 Dell™ S2815dn CACStar™ Smart Card Reader Installation and Configuration Guide Document protection for CAC/PIV enabled Multifunction Devices
…
S2815dn(40 pages) |
Parrot Headsets Zik-2Headsets PDF Operation & user’s manual Zik-2, 16 |
Technicolor Gateway TG582nUser Guide: Technicolor TG582n (SRG4Q6, Upd.25/01/2024) TG582n, 4 |
Xerox Printer Phaser 6200Xerox Phaser 6200 Guide (Maintenance instructions), @382Y8B Phaser 6200, 4 |
Black Box Switch Dual-Speed 10/100 Stackable HubDual-Speed 10/100 Stackable Hub Technical specifications - DON379 Dual-Speed 10/100 Stackable Hub, 3 |
Simplicity Lawn Mower 1691186Lawn Mower #GSHF4H 1691186, 6 |
Icom Amplifier IC-7800Amplifier Instruction manual (Icom IC-7800) IC-7800, 19 |
Cogent Systems PDA Mobile Verifier 3PDA #Z3G7R8 Mobile Verifier 3, 22 |
Iso-Tech Multimeter IDM19Multimeter Operating instructions (Iso-Tech IDM19) IDM19, 2 |
Inficon Laboratory Equipment Micro GC 3000AInficon Laboratory Equipment Operating manual (File: inficon-micro-gc-3000a-operating-manual-165, 17/11/2023) Micro GC 3000A, 165 |
Lorex Monitor L27LE10B#7I5VG5 L27LE10B: Lorex Monitor Owner Documentation L27LE10B, 24 |
Gigabyte Video Card GV-N275UD-896HOperation & user’s manual for Gigabyte GV-N275UD-896H Video Card GV-N275UD-896H, 32 |
BONFIGLIOLI Vectron DC Drives ACTIVE CUBE SeriesACTIVE CUBE Series (DC Drives ePDF User Guide, #G7GKL5) ACTIVE CUBE Series, 200 |