Manualios.com

Toshiba Adjustable Speed Drive H7 Series Operation Manuals

  • Adjustable Speed Drive H7 Series DC Drives
  • maOHlab8g21MA
  • Operation Manuals
  • PDF / Adobe Acrobat Reader
  • 230

Toshiba Adjustable Speed Drive H7 Series Manual Online:

3.45, 2139 votes
Toshiba Adjustable Speed Drive H7 Series User Manual
Toshiba Adjustable Speed Drive H7 Series User Guide
Toshiba Adjustable Speed Drive H7 Series Online Manual

Text of Toshiba Adjustable Speed Drive H7 Series User Guide:

  • Toshiba Adjustable Speed Drive H7 Series, 184 H7 ASD Operation Manual OCA 1, 2, or 3 U, V, or W Phase Short Circuit This fault occurs in the event of a short circuit at the U (1), V (2), or W (3) output leads of the ASD. • Output resistance of the U, V, or W leads of the ASD are not within the acceptable range. • Ensure that the ASD output and the motor are connected correctly. • Disconnect the motor from the ASD and retry. • Replace the applicable IGBT (U, V, or W). • Contact your Toshiba distributor for repair information. OCL Motor Overcur

  • Toshiba Adjustable Speed Drive H7 Series, 208 Appendix F H7 ASD Operation Manual Appendix F Link Reactor Information Selection of a link reactor (DCL) is often application specific. This document will provide guidelines for selecting link reactors for the H7 series of drives. The 600 Volt series drives above 15 HP allow for the reactor to be mounted internal to the drive. All other H7 drives require that the DCL be mounted externally. When selecting and mounting an external DCL, the air flow around the reactor, the thermal capability of the reactor, the allowable voltage loss, and the amount of harmonic reduction required will be co

  • H7 ASD Operation Manual Appendix E 207 Note: (*) Indicates that the item is one of a set of two parallel cables. Table 16. 600 Volt Drive Cable/Terminal Specifications. Model VT130H7U Circuit Breaker Rating (Amps) Typical Cable Size (AWG) Lug Size Input/Output Power Wire Size AM, FM, and II Terminals Control Terminal Strip ASD Input/Output Power Lug Wire Capacity 6015 15 #14 #2

  • Toshiba Adjustable Speed Drive H7 Series, 130 H7 ASD Operation Manual Regeneration Torque Limit #2 Program Torque Setting Parameters Manual Torque Limit Settings This parameter is used to set the negative torque upper limit for the #2 motor profile when multiple motors are controlled by a single drive or when a single motor is to be controlled by multiple profiles. Direct Access Number — F445 Parameter Type — Numerical Factory Default — 250.0 Changeable During Run — Yes Minimum — 0.00 Maximum — 250.0 Units — % Driving Torque Limit #3 Program Torque Setting Parameters Manual Torque Limit Settings This parameter is used to set the positive torque upper limit for the #3 motor profile when multiple motors

  • Toshiba Adjustable Speed Drive H7 Series, TOSHIBA INTERNATIONAL CORPORATION H7 Adjustable Speed Drive Please complete the Warranty Card supplied with the ASD and return it to Toshiba by prepaid mail. This will activate the 12 month warranty from the date of installation; but, shall not exceed 18 months from the date of purchase. Complete the following information about the drive and retain it for your records. H7 Model Number: H7 Serial Number: Project Number

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 43 Communication Setting Parameters Communication Settings Parity F801 RS232/485 Communication Time Out Time F803 RS232/485 Communication Time Out Action N/A Logic (TTL) Communication Time Out Action F804 Communication Interval (logic) F805 RS232/485 Wire Count F821 RS232/485 Response Time F825 TTL Master Output Selection F806 RS232/485 Master Output Selection F826 LCD Port Connection Type N/A Communication Reference Adjust Frequency Point Selection F810 S20 Settings Receive Address F860 Transmit Address F861 Speed Reference Station F862 Speed Reference Address F863 Torq

  • 212 Appendix H H7 ASD Operation Manual Table 21. 460 Volt 5.0 – 350 HP Spare Parts Listing. MODEL NUMBER INPUT FUSE CONTROL FUSE DC BUS FUSE CONTACTOR FAN RESISTOR XSISTORS RECT. MAIN CAPS MOV LCD DISPLAY VT130H7U R, S, and T FU1 (A) FU2(A) MS1 MS2 FAN1 FAN2 R21 (A) (B) (C) IGM RECT. CAP MOV 1 MOV (2)(3) EOI 4055 N/A N/A 00621 49648C N/A 50037 N/A N/A Reside on the Main Circuit PCB. 490

  • H7 ASD Operation Manual 175 Torque Reference Address Program Communication Setting Parameters S20 Settings The S20 system is Toshiba’s high-speed fiber optic communication system. This function is unavailable at the time of this release. Direct Access Number — F866 Parameter Type — Selection List Factory Default — 0 Fault Detect Station Number

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 67 Table 6 . Discrete Input Terminal Assignment Selections and Descriptions. 0 — Unassigned — No operation. 1 — F — Enables the Forward operation command. 2 — R — Enables the Reverse operation command. 3 — ST — Enables the Forward and Reverse operation commands (maybe disabled at F103). 4 — RES — Resets the device and any incurred faults. 5 — S1 — Preset Speed Command 1 is used as the LSB of the 4-bit nibble that is used to select a Preset Speed. 6 — S2 — Preset Speed Command 2 is used as

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 37 Terminal Selection Parameters Analog Input Functions Deceleration Time Adjustment F653 Torque Boost Adjustment F654 Reach Settings Low Speed Signal Output Frequency F100 Speed Reach Setting Frequency F101 FP Terminal Settings FP Terminal Meter Selection F676 FP Terminal Meter Adjustment F677 Input Special Functions ST Signal Selection F103 F/R Priority Selection (w/both on) F105 Input Terminal Priority F106 Extended Terminal Function F107 Line Power Switching (Commercial Power Switching) On Trip Enable/Disable F354 Switching-Frequency Setting and Enable/ Disable F355 Inverter-Output Swit

  • H7 ASD Operation Manual 63 S1 Input Terminal Assignment Program Terminal Selection Parameters Input Terminal Assignment S1 This parameter selects the functionality of the S1 input terminal. In addition, the input terminal must be specified as Normally Open or Normally Closed. This parameter sets the programmable S1 terminal to 1 of the 68 possible functions that ar

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 17 I/O Circuit Configurations Figure 7. Discrete input. Figure 8. RR Input. Figure 9. RX Input. Figure 10. VI/II input. Figure 11. P24 Output. Figure 12. PP Output. Figure 13. OUT1/OUT2 Output. Figure 14. FP Output. Figure 15. AM/FM Output. Figure 16. Fault Relay During Fault. www . ElectricalPartManuals . com

  • Toshiba Adjustable Speed Drive H7 Series, 32 H7 ASD Operation Manual Monitor Mode The Monitor mode allows the user to monitor motor performance variables, control settings, and configuration data during motor operation. There are 46 items that may be monitored from this mode. The items are listed and described below. Note: The Monitor mode is a read-only mode. The settings cannot be changed from the Monitor mode. For information on how to change the values, see the section titled Default Setting Changes on pg. 26. Running Frequency — Displays the H7 Output Frequency. Frequency Reference — Displays the Frequen

  • Toshiba Adjustable Speed Drive H7 Series, 96 H7 ASD Operation Manual RX2 Torque Reference Setpoint #2 (%) Program Torque Setting Parameters Setpoints RX2 This parameter is used to set the direction, gain, and bias of the RX2 input terminal when this terminal is used as the control input while operating in the Torque Control mode. This is accomplished by establishing an associated V/f output pattern for a given RX2 input level and motor load. See F222 for further information on this setting. This parameter sets RX2 Torque Reference Setpoint #2 (%) and is the output torque v

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual Appendix A 195 Conduit Extender Box (option) The Conduit Extender Box (P/N ASD-Conduit-1) may be used when more room is required at the ASD conduit connection point. This option makes adding and removing conduit easier and quicker. Installation 1. Remove the conduit plate 49462. 2. Install the Conduit Extender Box 53354, reusing the 2 screws from the conduit plate. 3. Make the conduit and wiring connections. 4. Install the Conduit Extender Box cover 53355. Figure 27. Conduit Extender Box. www . ElectricalPartManuals . com

  • Toshiba Adjustable Speed Drive H7 Series, 6 H7 ASD Operation Manual Installation and Connections The H7 True Torque Control 2 Adjustable Speed Drive may be set up initially by performing a few simple configuration settings. To operate properly, the ASD must be securely mounted and connected to a power source (3-phase AC input at the L1/R, L2/S, and L3/T terminals). The control terminals of the H7 may be used by connecting the terminals of the Control Terminal Strip to the proper sensors or signal input sources (see the section titled I/O and Control on pg. 11). Note: The optional ASD-Multicom boards may be used to expand the functionality of the AS

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual Appendix H 215 Table 24. 600 Volt 3.0 – 300 HP PCB Spare Parts Listing. MODEL NUMBER PCB Part Numbers 48048 48698 48700 48776 49500 50001 51580 52266 VT130H7U A, B, C, etc. PCB Typeform 6035 NB 6060 PB 6080 DB 6120 EB 6160 FB 6220 BAHLB 6270 CAHLB 6330 CAHLB 6400 CA JM1B 6500 CA JM1B 6600 C A M M1 B 52266 6750 C A K M B 52266 610K C A K M B 52266 612K C A K M B 52266 615K C A K M B 52266 620K C A L N B 52266 625K C A L N B 52266 630K C A N B 52266 The following PCBs are common to the above-listed typeforms. C

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 123 Motor Constant 1 (primary resistance) Program Motor Parameters Vector Motor Model This parameter is the measurement of the stator resistance and is considered a Motor Constant (unchanging). This value is used in conjunction with other constants to tune the motor. To use Vector Control, Automatic Torque Boost, or Automatic Energy- saving, the Motor Constant setting (motor tuning) is required. Direct Access Number — F402 Parameter Type — Numerical Factory Default — (drive dependent) Changeable During Run — No Minimum — 0.0 Maximum — 100,000 MΩ Units — Ω Motor Constant 2 (secondary resistance) Program Motor Parameters Vector Motor Model

  • Toshiba Adjustable Speed Drive H7 Series, Table of Contents H7 Operation Manual i Introduction ............................................................................................................................. 1 Safety Precautions ................................................................................................................... 2 Installation Precautions ...................................................................................................... 2 Maintenance Precautions ...............................

  • Toshiba Adjustable Speed Drive H7 Series, H7 ASD Operation Manual 127 Reverse Speed Limit Input Program Torque Setting Parameters Torque Control This parameter Enables/Disables the Reverse Speed Limit Input control function. When enabled and operating in the Torque Control mode, the reverse speed limit is controlled by the terminal selected here. If Setting is selected, the value set at F428 is used as the Reverse Speed Limit input. Settings: Disabled VI/II RR RX RX2 (option) Setting Direct Access Number — F427 Parameter Type — Selection List Factory Default — Disabled Changeable During Run — Ye s Reverse Speed Limit Level Program Torque Setting Parameter

  • Toshiba Adjustable Speed Drive H7 Series, 44 H7 ASD Operation Manual Communication Setting Parameters Communication Error Command Request Disposition on Error F830 Optional Parameters Optional Parameter #1 F890 Optional Parameter #2 F891 Optional Parameter #3 F892 Optional Parameter #4 F893 Optional Parameter #5 F894 Meter Terminal Adjustment Parameters FM FM Terminal Assignment F005 FM Terminal Adjustment F006 AM AM Terminal Assignment F670 AM Terminal Adjustment F671 Analog1 Analog 1 Terminal Assignment F672 Analog 1 Terminal Adjustment F673 Analog2 Analog 2 Terminal Assignment F674 Analog 2 Terminal Adjustment F675 Motor Parameters Vector

Related Products and Documents (DC Drives):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 ProForm PFTL721040 Operation & user’s manual proform/pftl721040-F53.pdf 29 Sep 2022 34
2 Lexmark 3350 - X Color Inkjet Service manual lexmark/3350-x-color-inkjet-4GC.pdf 05 Jul 2023 76
3 ActionTec MI424-WR Brochure & specs actiontec/mi424-wr-3V9.pdf 27 Apr 2023 5 0.24 Mb
4 Maxtor DiamondMax16 60 Product manual maxtor/diamondmax16-60-69F.pdf 01 Mar 2023 50
5 Remington PRO PACK HC5355AU Use & care manual remington/pro-pack-hc5355au-22K.pdf 07 Jul 2022 12
6 HP 170X - JetDirect Print Server Hardware installation manual hp/170x-jetdirect-print-server-PH3.pdf 22 Mar 2024 30 1.44 Mb

Similar Resources:

  • YASKAWA

    GA800 Series

    (130 pages)
    GA800 DriveAC Drive for Industrial ApplicationsInstallation & Primary OperationCatalog Code: GA80Uxxxxxxxx240 V class: 1 to 150 HP480 V class: 1 to 600 HPPDF …
  • Toro

    Greensmaster 3250-D

    (6 pages)
    Form No. 3325-838Operator’s Manual ®8- and 11-Blade Cutting UnitsGreensmaster®3250-DModel No. 04470—210000001 and UpModel No. 04471—210000001 and UpEnglish (GB) …
  • Siemens

    SINAMICS G120

    (32 pages)
    CU240B-2 and CU240E-2 Control Units ___________________ ___________________ ___________________ ___________________ ___________________ SINAMICS SINAMICS G120 CU240B-2 and CU240E-2 Control Units Compact Operating Instructions Edition 04/2015 04/2015 A5E35792002B AA Fundamental safety instructions 1 Scope of delivery 2 Installing 3 Commissioning …
  • HomeMatic

    HM-CC-VD

    (44 pages)
    Montage- und Bedienungsanleitung Funk-StellantriebHM-CC-VD Seite 4 - 23Installation and Operating Manual Radio-controlled valve driveHM-CC-VD Page 24 - 43DGB …
  • Vacon

    NX

    (6 pages)
    VACON NX QUICK HELP Start-up wizard The Start Up Wizard is activated when the power to the drive is turned on for the first time, or if the Start Up Wizard is activated from the System menu (P6.5.3) AND the power is turned OFF and back ON. The Start-up Wizard is a feature on the control keypad to facilitate the commissioning of the fre-quency converter. If …
  • Geckodrive

    G320

    (7 pages)
    G320 BRUSH SERVO DRIVE REV 7: July 15, 2010 Thank you for purchasing the G320 drive. The G320 DC servo drive is warranted to be free of manufacturing defects for 1 year from the date of purchase. Any customer who is dissatisfied with it or is unable to make it work will be cheerfully refunded the purchase price if the G320 is returned within 15 days of th …

Comments, Questions and Opinions: