Siemens RUGGEDCOM RS969 Installation Manual

Text of Siemens RUGGEDCOM RS969 User Guide:

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 2 Installing the Device Connecting the Failsafe Alarm Relay 13 Figure 13: DC and AC Power Supply Wiring Example NOTE • 88-300VDC rated equipment: A 300VDC appropriately rated circuit breaker must be installed. • A circuit breaker is not required for 12, 24 or 48 VDC rated power supplies. • Separate circuit breakers must be installed and separately identified. Section 2.3 Connecting the Failsafe Alarm Relay The Failsafe output relay is provided to signal critical error conditions that may occur on the RS969 series switches. The contacts are energized upon power up of the unit

• Siemens RUGGEDCOM RS969, Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 6 Connecting Power 1 Figure 3: Panel Mounting (Typical) 1. Flange 2. Install the supplied screws to secure the flanges to the panel. Section 2.2 Connecting Power The following sections describe how to connect power to the device: • Use only #16 gage copper wiring when connecting terminal blocks. • Equipment must be installed according to the applicable country wiring codes. • Section 2.2.1, “Power Supply Input Connectors Description” • Section 2.2.2, “Single High AC Power Supply Wiring Examples” • Section 2.2.3, �

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide ii Copyright © 2014 Siemens Canada Ltd. All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd.. Disclaimer Of Liabi

• Siemens RUGGEDCOM RS969, Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 14 Connecting to the Device Figure 14: Failsafe Alarm Relay Wiring Section 2.4 Connecting to the Device The following describes the various methods for accessing the ROS console and Web interfaces on the device. For more detailed instructions, refer to the ROS User Guide for the RS969. RS232 Console Port Connect a PC or terminal directly to the RS232 console port to access the boot-time control and ROS interfaces. The console port provides access to ROS's console and Web interfaces. IMPORTANT! The console port is intended to be used only as a temporary

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 3 Communication Ports 19 Communication Ports The RS969 can be equipped with various types of communication ports to enhance its abilities and performance. To determine which ports are equipped on the device, refer to the factory data file available through ROS. For more information on how to access the factory data file, refer to the ROS User Guide for the RS969. Each communication port type has a specific place in the RS969 chassis. 2 1 Figure 17: Port Assignment (M12 Connectors Shown) 1. M12 D-Coded Copper Ethernet Ports 2. Fibre Optic Ethernet Ports

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide 6/2014 Preface Introduction 1 Installing the Device 2 Communication Ports 3 Technical Specifications 4 Dimension Drawings 5 Accessories 6 Certification 7 RC1038-EN-02

• Siemens RUGGEDCOM RS969, Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 16 Cabling Recommendations Section 2.5 Cabling Recommendations Siemens recommends using SIMATIC NET industrial Ethernet shielded cables for all Ethernet ports. Section 2.5.1 Protection On Twisted-Pair Data Ports Siemens does not recommend the use of copper cabling of any length for critical, real-time substation automation applications. All copper Ethernet ports on RUGGEDCOM products include transient suppression circuitry to protect against damage from electrical transients and conform with IEC 61850-3 and IEEE 1613 Class 1 standards. This means that during a transient electrical event, c

• Chapter 7 Certification RUGGEDCOM RS969 Installation Guide 40 IEC Environmental Type Tests Section 7.4.3 IEC Environmental Type Tests Table: Environmental Type Tests Test Description Test Levels Severity Levels IEC 60068-2-1 Cold Temperature Test Ad -40 deg. C, 16 Hours N/A IEC 60068-2-2 Dry Heat Test Bd +85 deg. C, 16 Hours N/A IEC 60068-2-30 Humidity (Damp Heat, Cyclic) Test Db 95% (non-con

• Siemens RUGGEDCOM RS969, Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 10 Single High AC Power Supply Wiring Examples Section 2.2.2 Single High AC Power Supply Wiring Examples Figure 7: AC Power Supply Wiring Example (M23 Connector) Figure 8: AC Power Supply Wiring Example (Mini-Change Connector) NOTE • 100-240VAC rated equipment: A 250VAC appropriately rated circuit breaker must be installed. • When equipped with two HI voltage power supplies, independent AC sources can be used to power the product for greater redundancy.

• Siemens RUGGEDCOM RS969, Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 12 Dual High AC/DC Power Supplies Section 2.2.4 Dual High AC/DC Power Supplies Figure 11: AC and AC Power Supply Wiring Example Figure 12: DC and DC Power Supply Wiring Example

• Siemens RUGGEDCOM RS969, Chapter 3 Communication Ports RUGGEDCOM RS969 Installation Guide 22 Fiber Optic Ethernet Ports 21 Figure 21: LC Port 1. Tx Connector 2. Rx Connector For specifications on the available fiber optic Ethernet ports, refer to Section 4.4, “Fiber Optic Ethernet Port Specifications”.

• Chapter 2 Installing the Device RUGGEDCOM RS969 Installation Guide 8 Power Supply Input Connectors Description Figure 5: M23 Power Supply Connector Terminal # Description Usage 1 PS1 Live / + PS1 Live / + is connected to the positive (+) terminal if the power source is DC or to the (Live) terminal if the power source is AC. 2 PS1 Neutral / - PS1 Neutral / - is connected to the negative (-) termina

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 4 Technical Specifications Power Supply Specifications 23 Technical Specifications The following sections provide important technical specifications related to the device and available modules: • Section 4.1, “Power Supply Specifications” • Section 4.2, “Failsafe Relay Specifications” • Section 4.3, “Copper Data Port Specifications” • Section 4.4, “Fiber Optic Ethernet Port Specifications” • Section 4.5, “Operating Environment” • Section 4.6, “Mechanical Specifications” Section 4.1 Power Supply Specifications Power Supply Type Minimum Input Maximum

• RUGGEDCOM RS969 Installation Guide Table of Contents iii Table of Contents Preface ................................................................................................................ v Alerts .................................................................................................................................................. v Related Document

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 2 Installing the Device Power Supply Input Connectors Description 7 Section 2.2.1 Power Supply Input Connectors Description The RS969 family has 2 different power supply input connectors: a Mini A-coded male connector or M23 A-code male connector shown in the figures below. The Mini power connector only has 4 terminals, so only one power supply source is allowed to connect to the RS969 with the Mini power connector. The M23 power connector has 5 terminal pins, which means 2 power supply sources

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 7 Certification Agency Approvals 37 Certification The RS969 device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. • Section 7.1, “Agency Approvals” • Section 7.2, “FCC Compliance” • Section 7.3, “Industry Canada Compliance” • Section 7.4, “EMI and Environmental Type Tests” Section 7.1 Agency Approvals Agency Standards Comments CSA CSA C22.2 No. 60950-1, UL 60950-1 Approved CE EN 60950-1, EN 61000-6-2, EN 55022, EN 60825-1, E

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 1 Introduction Feature Highlights 1 Introduction The RUGGEDCOM RS969 is an industrially hardened, fully managed Ethernet switch providing dual fiber optical Fast Ethernet or Gigabit ports and eight Fast Ethernet copper ports in an IP65/IP67 rated package for protection against low pressure jets of water (IP65) or temporary immersion in water (IP67). Designed to operate reliably in harsh industrial environments the RS969 provides a high level of immunity to electromagnetic interference and heavy electrical surges typical of environments found in electric utility s

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 6 Accessories LC Fiber Optic (2/unit) 35 Figure 35: LC Port Mating Connector Description: IP67 Singlemode LC plug P/N 99-60-0002-001 LC Port Mating Connector Figure 36: LC Port Mating Connector Description: Multimode IP67 LC plug to LC connector, 3m P/N 99-43-0056-001 Figure 37: LC Port Mating Connector Description: Singlemode IP67 LC plug to LC connector, 3m P/N 99-43-0054-001

• Siemens RUGGEDCOM RS969, RUGGEDCOM RS969 Installation Guide Chapter 7 Certification IEEE 1613 Type Tests 39 Test Description Test Levels Severity Levels IEC 61000-4-17 Ripple on D.C. Power Supply D.C. Power ports 10% 3 Signal ports 2 kVAC (Fail-Safe Relay output) N/A D.C. Power ports 1.5kVDC N/A IEC 60255-5 Dielectric Strength A.C. Power ports 2 kVAC N/A Signal ports 5kV (Fail-Safe Relay output) N/A D.C. Power ports 5kV N/A IEC 60255-5 H.V. Impulse A.C. Power ports 5kV N/A Section 7.4.2 IEEE 1613 Type Tests Table: IEEE 1613 Type Tests

• Chapter 1 Introduction RUGGEDCOM RS969 Installation Guide 2 Feature Highlights • Meets IEEE 1613 (electric utility substations) • Exceeds IEC 61850-3 (electric utility substations) • Exceeds IEEE 61800-3 (variable speed drive systems) • Exceeds IEC 61000-6-2 (generic industrial environment) • Exceeds NEMA TS-2 (traffic control equipment) • Hazardous Location Certificat

• Siemens RUGGEDCOM RS969, Preface RUGGEDCOM RS969 Installation Guide vi Training For any questions about the documentation or for assistance finding a specific document, contact a Siemens sales representative. Training Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application. Siemens' Educational Services team thrives on providing our customers wit

More Instructions:

Siemens RUGGEDCOM RS969 Installation manual 22-03-2024 56

DOWNLOAD

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• SpectraLink 3000 (3 pages) C:\windows\TEMP\Technical bulletin 99-01.doc 10/19/00 Technical Bulletin 99-01 Bulletin #: CS-99-001 Product Type: Link 3000 Software Version: None Hardware Revision: None Access Level: Reseller Originator: Matt Jerger Status: Approved Approvers: John Elms, Gary Bliss Date: March 16, 1999 ---------------------------------- …

• Quantum P4000 (39 pages) Document 6331190-01, Ver. 1, Rel. 1, July 2003 1Quantum ATL P4000 andATL P7000 Prism FC470User’s Guide AddendumIntroduction 3Fibre Channel Description ...........................................................................3Prism FC470 Router Operation ...................................................................3Supported Fibre Channel Host Bus A …

• Asus RT-AC66U B1 (180 pages) Quick Start GuideRT-AC66U B1 Wireless-AC1750 Dual Band Gigabit RouterWEU15297 / Revised Edition V6 / March 2019WEU15065_RT-AC66U_B1_QSG_V5.indb 1 2019/3/5 14:59:32 …

• NETGEAR WNR2000-100NAR (2 pages) 24/7TECHNICAL SUPPORT*1-888-NETGEAR (638-4327)Email: [email protected], high-speed Internet connection •Simpleandsecurewaytoshareyourhigh-speedInternetconnection•WorkswitholderWireless-GdevicesandnewWireless-Ndevices•Push‘N’Connectsecurelyconnectsatthetouchof� …

• High walk HWW-3050 (69 pages) IIEEEEEE 880022..1111nn DDrraafftt 22..00 22..44GGHHzz WWiirreelleessss BBrrooaaddbbaanndd RRoouutteerr MMooddeell:: HHWWWW--33005500 User’s Manual Version: 1.0 Date of Issue: May 2009 …

• TP-Link ARCHER C3150 (2 pages) Quick Installation GuideAC3150 Wireless MU-MIMO Gigabit RouterConnect the Hardware If your Internet connection is through an Ethernet cable from the wall instead of through a DSL / Cable / Satellite modem, connect the Ethernet cable directly to the router’s Internet port, then follow steps 5 and 6 to complete the hardware connection.7106505905 REV1.0.2 …

Comments, Questions and Opinions: