Toshiba DB-EA4D Command Manual
|
Toshiba DB-EA4D, 2.2.34 Reboot the Printer to Switch to Main Firmware ASCII: GS 80H Hexadecimal: 1D 80 Decimal: 29 128 When the printer receives this command in the boot F/W, it returns ACK(06H) and then goes to Main F/W after rebooting. When the printer receives this command in the Main FW, it returns NACK (15H) and does not execute any more. 2.2.35 Cancel Downloading ASCII: GS 82H Hexadecimal: 1D 82 Decimal: 29 130 When the firmware receives this command during the downloading, the printer will cancel downloading and return to the state that the firmware is able to get and conduct the next command. This command
Toshiba DB-EA4D, 2.2 Command Descriptions 2.2.1 Printer Status ASCII: Since this command is used by Control transfer, command strings are not defined. (USB) DC4 01 00 (Parallel I/F) Hexadecimal: 14 01 00 (bRequest = 0x14, wValue = 0x01 0x00) Decimal: 20 01 00 This command returns the following status. The responses consist of 6 bytes. Byte #1 : Sensor status-1 Bit Function 0 1 0 Undefined Fixed to 0 - 1 PE(Paper End) sensor Not PE PE 2 BM(Black Mark) sensor Not Black Black Mark
Toshiba DB-EA4D, ¾ Duplex printing mode (Normal case) 1. Select Duplex Mode by 1F 62 02 00H 2. Select Front side by 1F 63 00 00H 3. Send Print data (Front side) 4. Send Form Feed code (1B 0CH) -> This can be omitted. 5. Select Back side by 1F 63 01 00H 6. Send Print data (Back side) 7. Send Form Feed code (1B 0CH) -> This can be omitted. 8. Send Start double side printing by 1F 64H Transporting to the cut position of the longer page by 1F 64H. Page2 Back side Start printing Page1 Front side 9. Perform Full Knife Cut by 1B 69H -> The paper is cut at the end of the lon
Configuration Setting Data (Hexadecimal) Description n11 Black mark cut position offset* 2 0xC5–0x3B (Default : 0x05) resolution=10/203"=1.25mm (Default Offset = 6.25mm) (Off set max = 73.82mm) n12 Paper width 00 01 02 (Default) 03 04 58mm 80mm 4.0” 5.1” Not used n13 Max. Speed of Variable 00(Default) 01 02 03 6.0 ips 5.0 ips
Toshiba DB-EA4D, n (hex) Remote diagnostic item Function B7 SBCS font version (4 digit ASCII) Return SBCS font version (total 6 bytes) n (hex) Remote diagnostic item Function BF Paper jam tally (8 digit ASCII numeric) Return paper jam tally (total 10 bytes) n (hex) Remote diagnostic item Function E3 CAM motor jam tally, (8 digit ASCII numeric) Return CAM motor jam tally (total 10 bytes) n (hex) Remote diagnostic item Function F3 FTP loader version (4 digit ASCII) Return FTP loader version (total 6 bytes) 2.2.4 Select Response Format (1F 16) ASCII: US SYN n m Hexadecimal: 1F 16 n m Decimal: 31 22 n m Values of m: Reserved (0x00) n = 00
Toshiba DB-EA4D, 2.2.27 Rolling ASCII print test (Duplex printing) - transaction test ASCII: GS d 23H n Hexadecimal: 1D 64 23 n Decimal: 29 100 35 n Values of n: Reserved (0x00) This command performs rolling ASCII print test only once on both side, and the page number on front side are always 00000001. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. The print layout is same as the simplex printing of Rolling ASCII print test. 2.2.28 H print test (Duplex printing) - transacti
2.2.20 Top margin adjustment - Adjustment or setting mode ASCII: GS d 10H n Hexadecimal: 1D 64 10 n Decimal: 29 100 16 n Range of n: F1 ≤ n ≤ 0F (@1/203”) This command performs top margin adjustment test. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this comman
Toshiba DB-EA4D, iv DB-EA4D Command manual (rev.00) 2.2.28 H print test (Duplex printing) - transaction test.............................................................................. 19 2.2.29 Dot check pattern print test (Duplex printing) - transaction test .................................................... 19 2.2.30 Graphics print test (Duplex printing) - transaction test.................................................................. 20 2.2.31 Switch to Flash Download Mode .......................................................................................
Toshiba DB-EA4D, 2.2.16 Rolling ASCII print test (Simplex printing) - transaction test ASCII: GS d 03H n Hexadecimal: 1D 64 03 n Decimal: 29 100 03 n Values of n: Reserved (0x00) This command performs rolling ASCII print test only once, so the page number is always 00000001. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. * It’s for the paper length mode. If the paper type is BM mode, the paper is cut at the next BM (w/ Cutter) or fed the next BM to cut position (w/o Cutter). If the paper
Toshiba DB-EA4D, 11 th byte Black mark cut position offset*2 0xC5–0x3B (Default : 0x05) resolution=10/203"=1.25mm (Default Offset = 6.25mm) (Off set max = 73.82mm) 12 th byte Paper width 00 01 02 (Default) 03 04 58mm 80mm 4.0” 5.1” Not used 13 th byte Max. Speed of Variable 00(Default) 01 02 03 6.0 ips 5.0 ips 4.0 ips 3.0 ips 14 th byte (Reserved) 15 th byte (Reserved) 16 th byte Paper Loading 00(Default) 01 Auto loading Manual loading (by Feed SW) * 1 When the value of n3 (Document length High byte) is 0x02, n2 (Low byte) should be set more than 0x30, and also should be set less or equal 0x52
10 DB-EA4D Command manual (rev.00) 2.2.12 Report Printer configuration ASCII: GS 0 ENQ n Hexadecimal: 1D 30 05 n Decimal: 29 48 05 n Values of n: Reserved (0x00) This command returns the following configuration setting as response data. Response data length consists of 16bytes. Response Configuration Setting
Toshiba DB-EA4D, 2.2.6 Print ASCII: ESC FF Hexadecimal: 1B 0C Decimal: 27 12 The processed data is printed and the printed paper is transported to the cut position. After processing this command, the paper is returned to the standby position of next page by a following command except paper cut command. In the case of the paper cut command, the paper is cut immediately and then the paper is returned to the standby position. This command is ignored in the duplex print mode. In the duplex print mode, Start Double Sided Printing command (1F 64) is effective instead of FF command. 2.2.7 Initialize Printer ASCII: ESC @ Hexadecimal: 1B 40
Toshiba DB-EA4D, 2.2.40 Start Double Sided Printing ASCII: US d Hexadecimal: 1F 64 This printer executes printing in the duplex printing mode by this command. And the printer also transports the printed paper to the cut position of longer by this command. After processing this command, the paper is returned to the standby position of next page by a following command except paper cut command. In the case of the paper cut command, the paper is cut immediately and then the paper is returned to the standby position. This
Toshiba DB-EA4D, Command sequence Function Remarks GS d 23H 1DH 64H 23H Rolling ASCII print test(Duplex Printing) GS d 24H 1DH 64H 24H H print test(Duplex Printing) GS d 25H 1DH 64H 25H Dot check pattern print test(Duplex Printing) GS d 27H 1DH 64H 27H Graphics print test(Duplex Printing) Flash Download Commands ESC [ } 1BH 5BH 7DH Switch to Flash Download Mode GS DC2 1DH 12H Return CRC GS DC3 1DH 13H Download to Flash Memory GS 80H 1DH 80H Reboot the Printer to Switch to Main Firmware GS 82H 1DH 82H Cancel downloading GS F0H 1DH F0H Check current active FW GS FFH 1DH FFH Reboot the Printer Duplex printing command US b 1FH 62H
31 DB-EA4D Command manual (rev.00) 4.2 Status command Command Function Response format -------------------- 14H 01H 00H Printer Status Not affect GS 0 EOT 1DH 30H 04H Get Printer ID, Remote Diagnostics Extension Affect GS 0 ENQ 1DH 30H 05H Report Printer configuration Affect GS 0 HT 1DH 30H 09H Get File Header Affect ESC [ } 1BH 5BH
Toshiba DB-EA4D, 4. Appendix 4.1 Printer Configuration Form A A FIRMWARE (Version, CRC) Boot Firmware Version : xxxxxx, xxxx FTP Firmware Version : xxxxxx, xxxx Main Firmware Version : xxxxxx, xxxx SBCS CG Version : xxxxxx, xxxx COMMUNICATION INTERFACE (T.B.D) Interface Type : xxxxxxxxxx Printer IP Address : xxx.xxx.xxx.xxx Subnet Mask : xxx.xxx.xxx.xxx
Toshiba DB-EA4D, 2.2.13 Get File Header ASCII: GS 0 HT n Hexadecimal: 1D 30 09 n Decimal: 29 48 09 n Get the File Header information specified by n. n = 00 : Boot 01 : Main FW 02 : Reserved 03 : SBCS CG 04 : Reserved 05 : Reserved 06 : Reserved 07 : FTP Loader F/W Response: Specified file header is returned. The file header consists of 16 byte as follows. ex. Ack + <Byte0 – Byte15> File Header Format : Byte0 2 2
Toshiba DB-EA4D, 2.2.3 Get Printer ID, Remote Diagnostics Extension ASCII: GS 0 EOT n Hexadecimal: 1D 30 04 n Decimal: 29 48 04 n Values of n: Refer to table - The printer sends the response that is set by n. Response: n <response data> 0Dh 6 < response data length < 17 n (hex) Remote diagnostic item Function 23 Printer Serial number (11 digit ASCII) Return Printer serial number (total 13 bytes) n (hex) Remote diagnostic item Function 27 Printer Model number (15 digit ASCII) Return Printer model number (total 17 bytes) n (hex)
Toshiba DB-EA4D, 2. Emulation 2.1 Command list The printer supports the following commands. Command sequence Function Remarks Status Commands (Real Time) -------------------- 14H 01H 00H Printer Status -------------------- 15H 02H n Printer Recovery Status Commands (Batch Mode) GS 0 EOT 1DH 30H 04H Get Printer ID, Remote Diagnostics Extension US SYN 1FH 16H Select Response Format Printer Function Commands ESC i 1BH 69H Perform Knife Cut ESC FF 1BH 0CH Print ESC @ 1BH 40H Initialize Printer ESC P
Toshiba DB-EA4D, Byte #5 : Error status-2 Bit Function 0 1 0 Label error in Label mode (no gap or no label found) No error Error 1 Over the length of printing area in label mode No error Error 2 Memory error (EERPOM) Read/Write error No error Error 3 Perforation detection error No error Error 4 Over the length of printing area in perforation mode No error Error 5 Thermal Head Error No error Error 6 Undefined Fixed to 0 - 7 Undefined Fixed to 0 - Byte #6 : Warning Bit Function 0 1 0 Und
Toshiba DB-EA4D, 2.2.31 Switch to Flash Download Mode ASCII: ESC [ } Hexadecimal: 1B 5B 7D Decimal: 27 91 125 Put the printer in IPL (Initial program loader) mode to process the flash download commands. When the printer receives this command, it replies ACK(0x06) and executes the reboot. Then the printer starts in IPL mode after the reboot. If the printer receive this command in IPL mode, it ignores the command and replies NACK(0x15). 2.2.32 Return CRC ASCII: GS DC2 n Hexadecimal: 1D 12 n Decimal: 29 18 n value of n: Calculate area 1 : Boot F/W 2 : Main F/W 3 : SBCS 4 - 6 : Reserved 7 : FTP Loader Return the calculated CRC in the select
Toshiba DB-EA4D, 2.2.30 Graphics print test (Duplex printing) - transaction test ASCII: GS d 27H n Hexadecimal: 1D 64 27 n Decimal: 29 100 39 n Values of n: Reserved (0x00) This command performs graphics pattern print test only once on one side, and the page number on front side are repeated 00000001 and 00000002. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. The print layout is same as the simplex printing of Graphics pattern print test. 1st Page Front side Back s
Toshiba DB-EA4D, ¾ Duplex printing mode (No cut command case) 1. Select Duplex Mode by 1F 62 02 00H 2. Select Front side by 1F 63 00 00H 3. Send Print data (Front side) 4. Send Form Feed code (1B 0CH) -> This can be omitted. 5. Select Back side by 1F 63 01 00H 6. Send Print data (Back side) 7. Send Form Feed code (1B 0CH) -> This can be omitted. 8. Send Start double side printing by 1F 64H Transporting to the cut position of the longer page by 1F 64H. Page2 Back side Front side Page1 Start printing 9. Select Front side by 1F 63 00 00H -> The paper is returned to the standby position of the next page without cutting paper. 10. Se
Toshiba DB-EA4D, ¾ Simplex printing mode (Normal case) 1. Select Simplex Mode by 1F 62 00 00H 2. Select Front side by 1F 63 00 00H(This can be omitted.) 3. Send Print data 4. Send Form Feed code (1B 0CH) Transporting to the cut position by Form Feed. side Front Start printing Page 5. Perform Knife Cut by 1B 69H -> The paper is cut at the end of the page and the left paper in the printer is returned to the standby position automatically. ¾ Simplex printing mode (No cut command case) 1. Select Simplex Mode by 1F 62 00 00H 2. Select Front side by 1F 63 00 00H(This can be omitted.) 3. Send Print data 4. Send Form Feed code (1B
Toshiba B-EX4 T1 Series Label Maker Product description
B-EX4 T1 Series |
Toshiba B-SA4 Label Maker Specifications
B-SA4 |
Toshiba B-SA4TP SERIES Label Maker Owner's manual
B-SA4TP SERIES |
Toshiba B-EX Series Label Maker Operation manual
B-EX Series |
Toshiba B-852 Label Maker Owner's manual
B-852 |
Toshiba B-852 Label Maker Operation & user’s manual
B-852 |
Toshiba B-SA4TP SERIES Label Maker Owner's manual
B-SA4TP SERIES |
Toshiba B-SX4T Series Label Maker Owner's manual
B-SX4T Series |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Philips | DVD795SA/99 | Quick use manual | philips/dvd795sa-99-SO1.pdf | 20 Oct 2023 | 2 | 0.73 Mb |
2 | Magnavox | AJ3840 | Specifications | philips/aj3840-1I1.pdf | 04 Aug 2023 | 2 | 0.37 Mb |
3 | Nissan | 2007 Frontier | Manual | nissan/2007-frontier-KW8.pdf | 23 Oct 2022 | 336 | |
4 | Manhattan | 175432 | Manual | manhattan/175432-I68.pdf | 07 Jul 2023 | 8 | |
5 | Cooper Lighting | Shaper 642 | Specification sheet | cooper-lighting/shaper-642-Z44.pdf | 31 Mar 2023 | 3 | |
6 | Whirlpool | G2IXEFMWS02 | User instructions | whirlpool/g2ixefmws02-7LJ.pdf | 11 Mar 2023 | 32 |
SATO
Revision Date : Mar. 2019v1.3Bluetooth Quick Installation GuideBluetooth快速安裝指南蓝牙模块快速安装指南Guía de instalación rápida del BluetoothGuia de instalação rápida BluetoothGuide d'installation rapide de BluetoothBluetooth SchnellinstallationsanleitungGuida rapida all'installazione di BluetoothBluetooth Hızlı Kurulum K …
Argox D2 Series(2 pages) |
Dymo
KnT Loading Dymo Labels 1http://www.keepntrack.com/mediawiki/index.php/Loading_Printer_Labels_and_PaperKeepnTrack - Hardware:Loading Dymo Labels (& Receipt Paper)Learn how to load labels and receipt paper into your Dymo printer.NOTE: This video shows the DYMO LabelWriter 450 Twin Turbo.Setting UpBe aware you should be using specific labels, the COMPa …
LabelWriter 450 Twin Turbo(2 pages) |
Pitney Bowes
Let’s get your SendKit up and running quickly…Let’s rst get together the things you will need:• The box containing your SendPro® Bluetooth SendKit.• A Welcome Email from Pitney Bowes containing your SendPro® Login details, if you use SendPro for the rst time.• A PC on which you have full admin rights to allow downloading and installin …
SendPro Bluetooth SendKit(8 pages) |
Intermec
Quick Start GuideMobile Label and Receipt Printer打印机快速入门指南印表機快速入門指南Guide de démarrage rapide de l’imprimanteDrucker Kurzanleitung프린터 빠른 시작 안내서Manual de Consulta Rápida da ImpressoraКраткое руководство по эксплуатации принтераGuía de comienzo rápido de la imp …
PB22(2 pages) |
AMT Datasouth
Fastmark 600 SeriesNew Heights of PerformanceFastmark 600 SeriesNew Heights of PerformanceFastmark 600 Series - Industrial Capacity in a Compact Desktop DesignFor a wide variety of applications that require high-capacity label printing from a desktop machine, the Fastmark 600Printer Series offers a user-friendly, cost-effective solution. With its small footp …
600(2 pages) |
Avery Dennison
MONARCH® , 9825®, 9855®, and 9860 are trademarks of Paxar Americas, Inc. Paxar® is a trademark of Paxar Corporation. Avery Dennison® is a trademark of Avery Dennison Corp. Oracle, JD Edwards, PeopleSoft, and Siebel are registered trademarks of Oracle Corporation and/or its affiliates. SAP and NetWeaver are trademarks of SAP AG in Germany and in sever …
Monarch 9825(10 pages) |
AEG Electrolux Hob 78031KF-MNAEG Electrolux Product Manual: 78031KF-MN PDF Operation & user’s manual - 2X8HFF 78031KF-MN, 20 |
Logitech Keyboard DINOVA EDGE#1KI4J5: DINOVA EDGE Keyboard Installing and features DINOVA EDGE, 4 |
ETen Cell Phone P300BPDF User Manual (@B81234), ETen P300B Cell Phone (01st Dec 2023) P300B, 39 |
TIE Telephone businesscom 16Feature handbook for TIE businesscom 16 Telephone businesscom 16, 16 |
Vaisala Transmitter DRYCAP DMT340 SERIESVaisala Transmitter DRYCAP DMT340 SERIES Operation & user’s manual DRYCAP DMT340 SERIES, 169 |
Motrona Controller CI800#I2M1D7: CI800 Controller Operating manual CI800, 18 |
Albrecht Transceiver DB 271Albrecht DB 271 Guide (Doc Type: Transceiver Manual ) DB 271, 27 |
Nitecore Battery Charger Intellicharger NEW i2Battery Charger #99E4G3 Intellicharger NEW i2, 2 |
Axiom Audio Speakers MILLENNIA M50 v2PDF Guide (@92A2I9), Axiom Audio MILLENNIA M50 v2 Speakers (Sat 10.2023) MILLENNIA M50 v2, 8 |
HeadRoom Headphone Portable Desktop AmpPortable Desktop Amp (Headphone ePDF User Manual, #DB471A) Portable Desktop Amp, 7 |
Allegion Card Reader aptiQ MT20WaptiQ MT20W Operation & user’s manual - 45W3YQ aptiQ MT20W, 37 |
Rain Bird Weather Station WS PRO LTWeather Station Installation manual (Rain Bird WS PRO LT) WS PRO LT, 22 |