Manualios.com

Toshiba Q9 True Torque Control2 Adjustable Speed Drive Quick Start Manual

  • Q9 True Torque Control2 Adjustable Speed Drive Inverter
  • maOHlab8g21MA
  • Quick Start Manual
  • PDF / Adobe Acrobat Reader
  • 73

Toshiba Q9 True Torque Control2 Adjustable Speed Drive Manual Online:

3.9, 2846 votes
Toshiba Q9 True Torque Control2 Adjustable Speed Drive User Manual
Toshiba Q9 True Torque Control2 Adjustable Speed Drive User Guide
Toshiba Q9 True Torque Control2 Adjustable Speed Drive Online Manual

Text of Toshiba Q9 True Torque Control2 Adjustable Speed Drive User Guide:

  • Q9 ASD Quick Start Guide 41 PROGRAM Utility Group User Units Selection F092 Motor Settings Base Frequency 1 F014 Base Voltage 1 F409 Torque Boost 1 F016 Electronic Thermal Protection 1 F600 Base Frequency 2 F170 Base Voltage 2 F171 Torque Boost 2 F172 Electronic Thermal Protection 2 F173 Autotune Control F400 Motor Slip Gain F401 Autotuning Control 2 F402 Motor Rated Capacit

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 16 Q9 ASD Quick Start Guide Lead Length Specifications Adhere to the NEC and any local codes during the installation of ASD/motor systems. Excessive lead lengths may adversely effect the performance of the motor. Special cables are not required. Lead lengths from the ASD to the motor in excess of those listed in Table 1 may require filters to be added to the output of the ASD. Table 1 lists the suggested maximum lead lengths for the listed motor voltages. Contact the Toshiba Customer Support Center for application assistan

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 5 Conductor Routing and Grounding • Use separate metal conduits for routing the input power, output power, and control circuits. • A separate ground cable should be run inside of the conduit with the input power, output power, and control circuits. • DO NOT connect CC to earth ground. •Use IICC terminal as the return for the VI/II (V/I) input. • Always ground the ASD to prevent electrical shock and to help reduce electrical noise. • It is the responsibility of the per

  • 26 Q9 ASD Quick Start Guide LCD Screen The LCD screen is the primary user input/output information center. Parameter settings may be viewed, or selected and changed using the LCD screen module of the EOI. To view or change a parameter setting using the LCD screen, press the Mode key until the Program menu is displayed. Turn the Rotary Encoder until the desired Pri

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 28 Q9 ASD Quick Start Guide PID Setup Mode The PID Setup (Proportional-Integral-Derivative) mode is comprised of parameter settings that are specific to the PID operating mode. PID is a closed-loop control technique that seeks error minimization by reacting to three values: One that is proportional to the error, one that is representative of the error, and one that is representative of the rate of change of the error. The quick-access items are listed below: Command Mode. Frequency Mode 1. VI/II (V/I) Reference 1. VI/II (V/I) Frequency 1. VI/II (V/I) Reference 2. VI/II (V/I) Frequency 2. PID-Control Switching. PID Feedback Selection. PID Feedba

  • Q9 ASD Quick Start Guide 15 Figure 4. The Grounding Capacitor Switch is used on typeforms — 200-volt 0.5 HP to 10 HP and the 25 and 30 HP/ 460-volt 1.0 HP to 250 HP. The value may be set to Maximum (default setting) or to Zero by pushing or pulling the switch actuator, respectively. Figure 5. The Grounding Capacitor Switch is used on typeforms — 200-v

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 58 Q9 ASD Quick Start Guide Cable/Terminal Specifications Installation should conform to the 2008 National Electrical Code Article 110 (NEC) (Requirements for Electrical Installations), all regulations of the Occupational Safety and Health Administration, and any other applicable national, regional, or industry codes and standards. Note: The following ratings are guidelines and shall not be the sole determining factor of the lug or wire size used with the Q9 ASD. Application-specific applicables, wire insulation type, conductor material, and local and regional regulations are but a few of the conside

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 49 Enclosure Dimensions The part numbering convention and the enclosure dimensions for the available models (typeforms) are listed below. Use the part numbering convention to identify the ASD typeform and for placing orders. Q9 Part Numbering Convention. Note: The Type 1 enclosed versions of these drives meet or exceed the specification UL 50- 1995, the Standard for Heating and Cooling Equipment, and complies with the applicable requirements for installation in a compartment handling conditioned air. Note: All Toshiba ASD enclosures ca

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 51 Table 4. 460-Volt Q9 ASD Systems. Frame ASD HP Rating Model Number VT130Q9U Enclosure Figure Number A Width (in/mm) B Height (in/mm) C Depth (in/mm) Mounting Hole Dimensions (in/mm) DEFGHR1R2 2 1 4015 Figure 23 5.1/130 10.0/254 6.0/152 8.7/220 4.5/114 N/A 0.098/2.5 0.217/5.5 2 4025 3 4035 3 5 4055 6.1/155 11.1/281 6.5/164 9.8/249 5.4/138 7.5 4080 4104110 6.9/175 12.6/320 11.1/283 6.2/158 0.236/6.0 5A 15 4160 8.3/210 7.6/194 7.5/190 0.118/3.0 0.276/7.0 20 4220 5B 25 4270 Figure 24 9.1/230 16.7/425 7.5/191 15.2/386 8.3/210 30 4330 6 40 4400 9.4/240 16.5/420 8.3/212 15.9/4

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 3 Equipment Inspection • Upon receipt of the equipment inspect the packaging and equipment for shipping damage. • Carefully unpack the equipment and check for parts that may have been damaged during shipping, missing parts, or concealed damage. If any discrepancies are discovered, it should be noted with the carrier prior to accepting the shipment, if possible. File a claim with the carrier if necessary and immediately notify your Toshiba Sales Representative. • DO NOT install the ASD if it is damaged or if it is missing any component(s). • Ensure that the rat

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 8 Q9 ASD Quick Start Guide System Setup Requirements • When using the ASD as an integral part of a larger system, it is the responsibility of the ASD installer/maintenance personnel to ensure that there is a fail-safe in place (i.e., an arrangement designed to switch the system to a safe condition if there is a fault or failure). • System safety features should be employed and designed into the integrated system in a manner such that system operation, even in the event of system failure, will not cause harm or result in system damage or injury to personnel (i.e., E-Off, Auto-Restart settings, System Interlocks, etc.). • The programming setup and system configuration of the ASD m

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 7 System Integration Precautions The following precautions are provided as general guidelines for the setup of the ASD within the system. • The Toshiba ASD is a general-purpose product. It is a system component only and the system design should take this into consideration. Please contact your Toshiba Sales Representative for application-specific information or for training support. • The Toshiba ASD is part of a larger system and the safe operation of the ASD will depend upon observing certain precautions and performing proper system integration. • Improperly designed or improperly installed system interlocks may render the motor una

  • Q9 ASD Quick Start Guide 11 Not all ASDs are equipped with internal primary power input fuses (HP dependent). When connecting two or more drives that have no internal fuse to the same power line as shown in Figure 1, it will be necessary to select a circuit-breaking configuration that will ensure that if a short circuit occurs in ASD 1, only MCCB2 trips, not MCCB1. If it is not feasib

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 29 Monitor Mode The Monitor mode allows the user to monitor motor performance variables, control settings, and configuration data during motor operation. There are 30 items that may be monitored from this mode. The items are listed and described below. Press the Rotary Encoder to access the listing of monitored parameters. Turn the Rotary Encoder to access subsequent monitored parameters. Note: The Monitor mode is a read-only mode. The settings cannot be changed from the Monitor mode. For information on how to change the value

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 22 Q9 ASD Quick Start Guide Typical Connection Diagram Figure 20. The Q9 ASD Typical Connection Diagram. Note: The AM, FM, and the +SU analog terminals are referenced to CC. The RR, RX, P24, and the PP analog terminals are referenced to CCA. The isolated V/I analog terminal references IICC. Note: When connecting multiple wires to any of ASD terminals, do not connect a solid wire and a stranded wire to the same terminal. Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 13 Power Connection Requirements Connect the 3-phase input power to the input terminals of the ASD at R/L1, S/L2, and T/L3 (see Figure 3 for the typical electrical connection scheme). Connect the output of the ASD to the motor from the ASD terminals U/T1, V/T2, and W/T3. The input and output conductors and terminal lugs used shall be in accordance with the requirements listed in the section titled Current/Voltage Specifications on pg. 56. If multiple conductors are used in parallel for the input or output power and it is necessary to use separate conduits, each parallel set shall have its o

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 25 Figure 21. The Q9 ASD Electronic Operator Interface Features. EOI Features LCD Screen — Displays configuration information, performance data (e.g., output frequency, bus voltage, torque, etc.), and diagnostic information. Rotary Encoder — Used to access the Q9 ASD menu selections, change the value of a displayed parameter, and performs the Enter key function. Turn the Rotary Encoder either clockwise or counterclockwise to perform the Up or Down functions of the displayed menu selection. Press the

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 33 PROGRAM Fundamental 1 Base Frequency 1 F014 Voltage Compensation F307 Base Voltage 1 F409 Disable Forward/Reverse Run F311 Upper-Limit Frequency F012 Lower-Limit Frequency F013 V/f Pattern F015 Torque Boost 1 F016 Acceleration Time 1 F009 Decel Time 1 F010 Accel/Decel Pattern 1 F502 Fundamental 2 Base Frequency 2 F170 Base Voltage 2 F171 Torque Boost 2 F172 Electronic Thermal Protection 2 F173 Acceleration Time 2 F500 Deceleration Time 2 F501 Accel/Decel Pattern 2 F503 Accel/Decel Switching Frequency 1 F505 Panel Control Panel Direction F008 Panel Stopping Pattern F721 Panel Accel/Decel Selection F504 Switch-On-The-Fly F295 Lock CMOD/FMOD F736 P

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 36 Q9 ASD Quick Start Guide PROGRAM Special Controls Forced Fire-Speed F650 Preset Speed 15 F294 Power Switching F354 Power Switching Frequency F355 ASD Switching Wait Time F356 Commercial Power Wait Time F357 Commercial Power Hold Time F358 DC Injection Braking Start Frequency F250 DC Injection Braking Current F251 DC Injection Braking Time F252 DC Injection On During Direction Change F253 Shaft Stationary F254 kWH Memory Selection F748 kWH Units Selection F749 Preset Speeds Preset Speed 1 F018 Preset Speed 2 F019 Preset Speed 3 F020 Preset Speed 4 F021 Preset Speed 5 F022 Preset Speed 6 F023 Preset Speed 7 F024 Preset Speed 8 F287 Preset Sp

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 2 Q9 ASD Quick Start Guide Special Symbols To identify special hazards, other symbols may appear in conjunction with the DANGER, WARNING, and CAUTION signal words. These symbols indicate areas that require special and/or strict adherence to the procedures to prevent serious injury to personnel or loss of life. Electrical Hazard Symbol A symbol that is comprised of an equilateral triangle enclosing a lightning bolt indicates a hazard of injury from electrical shock or burn. Explosion Hazard Symbol A symbol that is comprised of an equilateral triangle enclosing an explosion indicates a hazard of injury from exploding parts. Equipment Warning Labels DO NOT atte

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, 12 Q9 ASD Quick Start Guide Connecting the ASD Refer to the section titled Installation Precautions on pg. 4 and the section titled Lead Length Specifications on pg. 16 before connecting the ASD and the motor to electrical power. Power Connections Contact With 3-Phase Input/Output Terminals May Cause Electrical Shock Resulting In Injury Or Loss Of Life. See Figure 20 on pg. 22 for a system I/O connectivity schematic. An inductor (DCL) may be connected across the PO and PA/+ terminals to provide additional filtering. When not used, a jumper must be connected across these terminals (See Figure 20 on pg. 22). PA/+ and PB are us

  • Q9 ASD Quick Start Guide 57 Table 6. 460-Volt UL Type-1/IP-20 Chassis Standard Ratings Table. Model Number VT130Q9U 100% Output Current Continuous Overload Current 110% for 60 Seconds Input Voltage 3-Ph 50/60 ±2 Hz Output Voltage 3-Ph Variable Frequency Typical Motor HP 4015 2.1 A 2.3 A 380 – 480 VAC (±10%) Input Voltage Level (Max.) 1.0 4025 3.4 A 3.7 A 2.0 4035 4.8 A 5.3

  • Toshiba Q9 True Torque Control2 Adjustable Speed Drive, Q9 ASD Quick Start Guide 43 PROGRAM Frequency Settings PG Reference 1 F234 PG Frequency 1 F235 PG Reference 2 F236 PG Frequency 2 F237 Jog Run Frequency F260 Jog Stop Control F261 My Function Unit 1 My Function Selection F977 Input Function Target 1 F900 Input Function Command 1 F901 Input Function Target 2 F902 Input Function Command 2 F903 Input Function Target 3 F904 Output Function Assigned F905 My Function Unit 2 Input Function Target 1 F906 Input Function Command 1 F907 Input Function Target 2 F908 Input Function Command 2 F909 Input Function Target 3 F910 Output Function Assigne

Related Products and Documents (Inverter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Daewoo FR-780NB Installation instructions manual daewoo/fr-780nb-1G4.pdf 30 May 2023 14 0.7 Mb
2 Vienna Acoustics Strauss Owner's manual vienna-acoustics/strauss-OUL.pdf 12 Sep 2023 8 0.02 Mb
3 Blue Rhino GBT726M Owner's manual blue-rhino/gbt726m-571.pdf 07 Aug 2023 16 4.49 Mb
4 Murphy HV1000 Brochure & specs murphy/hv1000-1Y9.pdf 23 Feb 2023 6
5 Sega 74065 Instruction manual sega/74065-NCB.pdf 30 Oct 2022 2 0.22 Mb
6 RCA M4304 - 4 GB Digital Player Operation & user’s manual rca/m4304-4-gb-digital-player-BTQ.pdf 30 Dec 2022 29 3.02 Mb

Similar Resources:

  • Hitachi

    X200 Series

    (25 pages)
    X200 Series Inverter Quick Reference Guide • Single-phase Input 200V class • Three-phase Input 200V class • Three-phase Input 400V class Hitachi Industrial Equipment Systems Co., Ltd. Manual No. NT3011XB • Sep 2007 …
  • MPPT

    MC2440N10

    (9 pages)
    Version: 1.02The above information is subject to change without prior notice.MC Series MPPT Solar Charge ControllerUser ManualMC2420N10/ MC2430N10/ MC2440N10/ MC2450N10ModelBattery voltageMax. PV open circuit voltageCharge currentMax. PV input powerMC2420N10 MC2430N10 MC2440N10 MC2450N1012V/24V92V(25℃);100V(Lowest ambient temperature)20A 30A 40A 50A260W/ …
  • Kohler

    SDMO PRO 3000 E C5

    (18 pages)
    Manuel d'utilisation et d’entretien(Notice originale)Instruction and maintenance manual(Translation of the original note)Manual de utilización y mantenimiento(Traducción de la información original)Benutzer- und Wartungshandbuch(Übersetzung der Original-Anleitung)Gebruiks- en onderhoudshandleiding(Vertaling van de oorspronkelijke handleiding)Vedlig …
  • Fischer Panda

    8000

    (250 pages)
    Panda_12000-15000_xControl_PMS_eng.R01 18.12.15Manual marine generatorPanda 12000x PMS 12 kVA 230V - 50 HzPanda 15000x PMS 15 kVA 230V - 50 HzSuper silent technology …
  • Kubler

    CODIX 533

    (62 pages)
    BedienungsanleitungSollwertgeber CODIX 533englishdeutschfrançaisitalianoespañolGenerador de valores de consigna CODIX 533 Salidas 0 … 12 V y 0 … 24 mAGeneratore di valore di consegna CODIX 533 con uscite 0 … 12 V e 0 … 24 mAGénérateur de consigne CODIX 533 avec sorties 0 … 12 V et 0 … 24 mASetpoint generator CODIX 533 Output 0 … 12 V …
  • Agilent Technologies

    E4400B

    (226 pages)
    Keysight/Agilent/HP E4430B Manual Get Pricing & Availability at ApexWaves.com Call Today: 1-800-915-6216 Email: [email protected] https://www.apexwaves.com/signal-generators/keysight-technologies/e44xx-esg-signal-generators/E4430B …

Comments, Questions and Opinions: