Toshiba AJ65VBTCU-68ADVN Operation & User’s Manual
|
Toshiba AJ65VBTCU-68ADVN, 5 - 26 5 - 26 MELSEC-A 5 PROGRAMMING (2) Initial setting by remote device station initialization procedure registration function (a) Setting of target station numbers Set the station numbers to which initial setting will be made. Set the target station numbers to "1" and "4". (b) Selection of procedure registration (part 1) Make setting for the AJ65VBTCU-68ADI. Click Procedure registration of target station number "1". (c) Setting of procedure registration (par
6 - 6 6 - 6 MELSEC-A 6 TROUBLESHOOTING Are the station number setting switches properly (not overlapping with other stations)? Set the station number setting switches properly Set the correct transmission speed
Toshiba AJ65VBTCU-68ADVN, 3 - 14 3 - 14 MELSEC- A 3 SPECIFICATION Table 3.6 Remote I/O Signal Details (2/2) Device No. Signal Name Description RX(n+1)A Error status flag Turns on at occurrence of an input range setting error, average time/number of times setting error or E 2 PROM write error (RXnC). Does not turn on at occurrence of the watchdog timer error. ("RUN" LED goes off.) RY(n+1)A Error reset request flag RX(n+1)A Error status flag : Performed by sequence ladder : Performed by AJ65VBTCU-68ADVN/ADIN RWrn
Toshiba AJ65VBTCU-68ADVN, 4 - 23 4 - 23 MELSEC- A 4 SETUP AND PREPARATION BEFORE OPERATION 4.11 Maintenance and Inspection There are no special inspection items for the AJ65VBTCU-68ADVN/ADIN module, but follow the inspections items describes in the PLC CPU User's Manual so that the system can always be used in the best condition.
Toshiba AJ65VBTCU-68ADVN, 5 - 19 5 - 19 MELSEC-A 5 PROGRAMMING (e) Selection of procedure registration (part 2) Make setting for the AJ65VBTCU-68ADVN. Click Procedure registration of target station number "4". (f) Setting of procedure registration (part 2) Set the conditions and execution for the AJ65VBTCU-68ADVN. When the initial data processing request flag (RX18) tur
Toshiba AJ65VBTCU-68ADVN, 3 - 8 3 - 8 MELSEC- A 3 SPECIFICATION 3.4 Function List The AJ65VBTCU-68ADVN/ADIN function list is shown in table 3.3. Table 3.3 AJ65VBTCU-68ADVN/ADIN function list Item Description Refer to Sampling processing Perform A/D conversion of an analog input value one by one and store the result into the remote register each time. Section 3.4.1 Section 3.6.4 Average processing Perform A/D conversion by the preset number
3 - 11 3 - 11 MELSEC- A 3 SPECIFICATION (1) Remote I/O signal list for ver. 1 remote device station (ver. 1 compatible slave station) setting Table 3.4 indicates the assignment and names of the remote I/O signals fo
Toshiba AJ65VBTCU-68ADVN, A - 1 A - 1 SAFETY PRECAUTIONS (Always read these precautions before using this equipment.) Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. Refer to the user’s manual of
Toshiba AJ65VBTCU-68ADVN, 6 - 5 6 - 5 MELSEC-A 6 TROUBLESHOOTING 6.4 Troubleshooting for the Case where the "ERR." LED of the Master Station Flickers The "ERR"LED on the master station is flashing Do the parameter setting and the installed system configuration match properly? Are the master station link special registers SW0080 to SW0083 (other station date link status) turned on? Are the master station link speci
Toshiba AJ65VBTCU-68ADVN, 3 - 12 3 - 12 MELSEC- A 3 SPECIFICATION (2) Remote I/O signal list for ver. 2 remote device station (ver. 2 compatible slave station) setting Table 3.5 indicates the assignment and names of the remote I/O signals for ver. 2 remote device station (ver. 2 compatible slave station) setting. Table 3.5 Remote I/O Signal List for Ver. 2 Remote Device Station (Ver.
Toshiba AJ65VBTCU-68ADVN, 6 - 3 6 - 3 MELSEC-A 6 TROUBLESHOOTING (3) When the AJ65VBTCU-68ADVN/ADIN "RUN" LED is off Check item Corrective action Is an attempt made to perform operation in the normal mode with the mode select switch set in the test mode? Switch power on again after setting the mode select switch to the normal mode. Has the watchdog timer error occurred? Using the link special registers (SW0084 to SW0087) of the master module, check the watchdog timer error and power on the AJ65VBTCU-68ADVN/ADIN again. If
Toshiba AJ65VBTCU-68ADVN, 4 - 10 4 - 10 MELSEC- A 4 SETUP AND PREPARATION BEFORE OPERATION 4.6 Station Number Setting The station number setting of the AJ65VBTCU-68ADVN/ADIN determines the buffer memory addresses of the master module where the remote I/O signals and read/write data are stored. For details, refer to the user's manual of the master module used. 4.7 Facing Direction of the Module Installatio
Toshiba AJ65VBTCU-68ADVN, 3 - 10 3 - 10 MELSEC- A 3 SPECIFICATION 3.5 Remote I/O Signals This section describes the assignment and functions of the remote I/O signals. 3.5.1 Remote I/O signal list Remote inputs (RX) mean the input signals from the AJ65VBTCU-68ADVN/ADIN to the master module, and remote outputs (RY) mean the output signals from the master module to the AJ65VBTCU-68ADVN/ADIN. In communications with the master station, the AJ65VBTCU-68ADVN/ADIN uses 32 poi
Toshiba AJ65VBTCU-68ADVN, 3 - 4 3 - 4 MELSEC- A 3 SPECIFICATION 3.3.1 Voltage input characteristics of the AJ68VBTCU-68ADVN The voltage input characteristic graph of the AJ65VBTCU-68ADVN is shown below. 3 2 1 4095 4000 2000 -2000 -4000 -4096 0 1 -15 -10 -5 0 5 10 1 5 Analog input voltage (V) Analog input parcitcal value -96 Digital output value Number Analog Input Range Setting Offset Value Gain Value Digital Output Value* Maximum
Toshiba AJ65VBTCU-68ADVN, 6 - 1 6 - 1 MELSEC-A 6 TROUBLESHOOTING 6 TROUBLESHOOTING The details of the errors which may occur when using the AJ65VBTCU-68ADVN/ADIN and troubleshooting are described. 6.1 Error Code List If an error occurs (the "RUN" LED of the AJ65VBTCU-68ADVN/ADIN flickers) during write of data from the PLC CPU to the master module, the corresponding error code is stored into the remote register RWrn+8 of the AJ65VBTCU-68ADVN/ADIN. Table 6.1 E
Toshiba AJ65VBTCU-68ADVN, A - 3 A - 3 [Starting and Maintenance Precautions] ! CAUTION Do not touch the pin while the power is on. Doing so may cause malfunction. Be sure to shut off all phases of the external power supply used by the system before cleaning. Not doing so can cause the module to fail or malfunction. Never disassemble or modify the module. This may cause breakdo
Toshiba AJ65VBTCU-68ADVN, 4 - 20 4 - 20 MELSEC- A 4 SETUP AND PREPARATION BEFORE OPERATION (From the previous page) Latches Pliers 6) Press both ends of the plug cover After pressing the center part of the plug cover, press both ends of the plug cover where latches are located. Verify that the latches engage with the plug body. [Correct example] 0.2mm or less [Wrong example] 7) Check the press-fit condition (viewing from the wiring side). Viewing from the wiring side, check that the
Toshiba AJ65VBTCU-68ADVN, A - 5 A - 5 INTRODUCTION Thank you for choosing a Mitsubishi MELSEC-A Series General Purpose Programmable Controller. Before using your new PLC, please read this manual thoroughly to gain an understanding of its functions so you can use it properly. CONTENTS SAFETY PRECAUTIONS..............................................................................................................................A- 1 REVISIONS ...
4 - 2 4 - 2 MELSEC- A 4 SETUP AND PREPARATION BEFORE OPERATION CAUTION Dispose of the product as industrial waste. Use the module in the environment indicated in the general specifications given in this manua
Toshiba M200 - Portege - Pentium M 1.5 GHz Control Unit Maintenance manual
M200 - Portege - Pentium M 1.5 GHz |
Toshiba VF-MB1 Control Unit Instruction manual
VF-MB1 |
Toshiba TOSVERT VF-AS1 Series Control Unit Instruction manual
TOSVERT VF-AS1 Series |
Toshiba 810 Control Unit Operation & user’s manual
810 |
Toshiba RS-485 Control Unit Instruction manual
RS-485 |
Toshiba Adjustable Speed Drive H7 Series Control Unit Specification
Adjustable Speed Drive H7 Series |
Toshiba M200 - Portege - Pentium M 1.5 GHz Control Unit Characteristics
M200 - Portege - Pentium M 1.5 GHz |
Toshiba M2 Control Unit Operation & user’s manual
M2 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Ford | 07 Sport Trac | Quick reference manual | ford/07-sport-trac-1U1.pdf | 21 Sep 2023 | 2 | 1.27 Mb |
2 | Sonel | MPI-520 | Operating manual | sonel/mpi-520-HN7.pdf | 24 Aug 2023 | 72 | |
3 | Sony | HDR-PJ200/B | Specifications | sony/hdr-pj200-b-Y4V.pdf | 05 Nov 2022 | 3 | |
4 | Rolls | MP26 | Manual | rolls/mp26-R26.pdf | 24 Feb 2024 | 1 | 0.02 Mb |
5 | Toyota | Corolla TNS600 2004 | Installation instructions manual | toyota/corolla-tns600-2004-QIH.pdf | 28 Sep 2023 | 18 | |
6 | Carson | SA-450-80 | Installation and operating manual | carson/sa-450-80-O28.pdf | 28 Mar 2023 | 7 | 0.1 Mb |
Siemens
Milling _______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ …
SINUMERIK 840D sl(666 pages) |
ARI
R-30 RM .IOM.ENG01 R-30 RM 3W Pressure Reducing Control Valve 3 Way The following is a step by step narrated description of the Eliptix R-30RM 3W Pressure Reducing Valve installation, operation and maintenance processes. The A.R.I. R-30 Series is a line of metal, diaphragm-operated, hydraulic control valves. The valves are suitable for in …
Eliptix R-30RM(20 pages) |
Rapid Controls
SAB-Q2 Quick Start January 12, 2011SAB-Q2 Quick StartThis document aims to provide a systematic setup procedure to enable you to setup and use your SAB-Q2 as easily as possible. This guide will concentrate on connections and basic setup. More information is available for advanced setup, refer to the SAB-Q2 manual. If you do not have a SAB-Q2 manual, call Rap …
SAB-Q2(5 pages) |
AGFEO
TelekommunikationAS 40 - ModulInstallation of the moduleSafty notes ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢!Before unlocking the cover, remove the 230 V mains plugfrom the telephone system.Opening the housing ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢ …
AS 40(2 pages) |
Viking
TECHNICAL DATA2” MODEL G-2000 DRY VALVE RISER ASSEMBLYPage 1 of 13The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: [email protected] the Viking website for the latest edition of this technical data page www.vikinggroupinc.com.Form No. F_0111 …
G-2000(13 pages) |
aquabrass
Last revision : 21/08/2019aquabrass.com1TURBO Totem T12005TURBO TOTEM T-12005 1/2” thermostatic valve Valve thermostatique 1/2” T 12005 Guide d’installationInstallation Guide
…
TURBO Totem T12005(11 pages) |
REVELL Toy PETERBILT 359 WRECKERREVELL Product User Manual: PETERBILT 359 WRECKER PDF Manual - M9H3W9 PETERBILT 359 WRECKER, 40 |
Home Decorators Collection Indoor Furnishing M61267X9-BLAssembly instructions manual for Home Decorators Collection M61267X9-BL Indoor Furnishing M61267X9-BL, 7 |
Avaya IP Phone IP Office 1616Avaya IP Office 1616 Guide (Doc Type: IP Phone Quick reference manual) IP Office 1616, 4 |
Carrier Furnace Deluxe 58SXBCarrier Furnace Installation instructions manual (File: carrier-deluxe-58sxb-installation-instructions-manual-10, Sat 12.2023) Deluxe 58SXB, 10 |
Giant Alarm System Car Alarm JJ-CA-05#P2EY26: JJ-CA-05 Car Alarm Operating instruction JJ-CA-05, 4 |
Graco Paint Sprayer GH 311279D#V732ZK GH 311279D: Graco Paint Sprayer Owner Documentation GH 311279D, 44 |
Brother Fax Machine MFC-3320CN#3P5K57 MFC-3320CN: Brother Fax Machine Owner Documentation MFC-3320CN, 13 |
Brother Sewing Machine BAS-364EBrother Product Guide: BAS-364E PDF Instruction manual - XM11B7 BAS-364E, 68 |
Lightronics Dimmer AS-62DUser Manual: Lightronics AS-62D (PDRTEX, Upd.Thu 11.2023) AS-62D, 6 |
Wega Coffee Maker Espresso Coffee MachineUser Guide: Wega Espresso Coffee Machine (211RTF, Upd.Thu 11.2023) Espresso Coffee Machine, 104 |
Rayburn Stove Heatranger 480GBRayburn Stove Heatranger 480GB Installation instructions manual Heatranger 480GB, 37 |
Thermal Dynamics Power Supply Pak Master 75XL PlusManual: Thermal Dynamics Pak Master 75XL Plus (G7389X, Upd.26th Dec 2023) Pak Master 75XL Plus, 74 |