Siemens simatic ET 200MP Manual 

Text of Siemens simatic ET 200MP User Guide:

• Siemens simatic ET 200MP, Product overview 2.2 Functions Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 18 Manual, 11/2017, A5E03612323-AC Module-internal Shared Input/Shared Output (MSI/MSO) The Module-internal Shared Input function allows an input module to make its input data available to up to two additional IO controllers. Each controller has read access to the same channels. The Module-internal Shared Output function allows an output module to make its output data available to up to two IO controllers. One IO controller has write access. A second IO controller can have read access to the same channels. You can find more information on this topic in the ST

• Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 45 Response times B B.1 Response times of the ET 200MP Introduction The response time of the IM 155-5 PN ST is made up of: ● the update time configured for the IM as IO device. plus ● the backplane bus cycle time. Note Validity of the formula The following formu

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.1 Status and error displays Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 28 Manual, 11/2017, A5E03612323-AC Meaning of the LEDs P1 LINK/TX/RX, P2 LINK/TX/RX Table 5- 2 Meaning of the LEDs P1 LINK/TX/RX, P2 LINK/TX/RX LEDs P1 LINK/TX/RX, P2 LINK/TX/RX Meaning Remedy Off There is no Ethernet connection between the PROFINET interface of your PROFINET device and a communication partner (e.g. IO controller). Check whether the bus cable to the switch/IO controller is interrupted. On There is an Ethernet connection between the PROFI

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 37 USI structure = W#16#0007 Table 5- 14 USI structure = W#16#0007 Data block name Contents Note Bytes USI W#16#0007 Manufacturer-specific diagnostic data if the configuration of the interface module power supply is different from the parameterized configuration 2 Error IM power supply: Power supply <bit 0 in the least significant byte can be 0 or 1> Power supply of the interface module B#16#00 Power supply of the interface module is not active.

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 30 Manual, 11/2017, A5E03612323-AC 5.2.2 Triggering of a hardware interrupt Triggering of a hardware interrupt When a hardware interrupt occurs, the CPU interrupts execution of the user program and processes the hardware interrupt OB. The event that triggered the interrupt is entered in the start information of the hardware interrupt OB. Note Diagnostics "Hardware interrupt lost" (from I/O module) Avoid creating h

• Siemens simatic ET 200MP, ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ SIMATIC ET 200MP Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual 11/2017 A5E03612323 -AC Preface Documentation guide 1 Product overview 2 Wiring 3 Parameter 4 Interrupts and diagnostic, error, and system alarms 5 Technical specifications 6 Dimension drawing A Response times B

• Siemens simatic ET 200MP, Product overview 2.2 Functions Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 17 Device replacement without PG It is easy to replace IO devices that support this function: ● The device name does not have to be assigned with the PG. The replaced IO device is assigned the device name by the IO controller. The IO controller uses the configured topology and the neighboring relationships determined by the IO devices for this purpose. All involved devices must support the LLDP protocol (Link Layer Dis

• Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 23 Parameter 4 4.1 Parameters Table 4- 1 Parameters for IM 155-5 PN ST interface module Parameters Value range Default setting Efficiency range Connection to supply voltage L+ Connection/No con- nection Connection ET 200MP Configuration control D

• Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 6 Manual, 11/2017, A5E03612323-AC Documentation guide 1 The documentation for the SIMATIC S7-1500 automation system and the SIMATIC ET 200MP distributed I/O system is arranged into three areas. This arrangement enables you to access the specific content you require. Basic information The

• Parameter 4.2 Description of parameters Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 25 Requirement In order to generate a diagnostics, the IM 155-5 PN ST interface module must have been configured once. See also Diagnostic alarms (Page 30) 4.2.2 Configuration control "Configuration control" param

• Siemens simatic ET 200MP, Technical specifications Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 40 Manual, 11/2017, A5E03612323-AC Article number 6ES7155-5AA01-0AB0 Power Infeed power to the backplane bus 14 W Power available from the backplane bus 2.3 W Power loss Power loss, typ. 4.5 W Address area Address space per module • Address space per module, max. 256 byte; per input / output Address space per station • Address space per station, max. 512 byte; per input / output Hardware configuration Integrated power supply Yes System

• Siemens simatic ET 200MP, Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 20 Manual, 11/2017, A5E03612323-AC Wiring 3 3.1 Terminal assignment 24V DC power supply The following table shows the signal names and the descriptions of the pin assignment for a 24 V DC supply voltage. Table 3- 1 Pin assignment 24 V DC supply voltage View Signal name 1 Designation 1L+ 24 V DC 2L+ 24 V DC (for looping through) 2 1M Ground 2M Ground (for looping through) 2 1 1L+ and 2L+ a

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 35 Structure USI = W#16#0002 Table 5- 9 Structure of the USI = W#16#0002 Data block name Contents Note Bytes USI W#16#0002 Manufacturer-specific diagnostic data if the permitted number of power supply modules is exceeded 2 The first surplus module is located in slot: <No.> Slot B#16#00 to B#16#1F 1 Followed by 3 reserved bytes Reserved 1 Reserved 1 R

• Siemens simatic ET 200MP, Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 11 Product overview 2 2.1 Properties Article number 6ES7155-5AA01-0AB0 View of the module Figure 2-1 View of the IM 155-5 PN ST interface module Properties ● Technical properties – Connects the ET 200MP distributed I/O system with PROFINET IO – 24V DC power supply (SELV/PELV) – PROFINET IO connection using RJ45 bus connector ● Supported functions (Page 13)

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.1 Status and error displays Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 27 Meaning of the LEDs RUN/ ERROR/ MAINT Table 5- 1 Meaning of the LEDs RUN/ ERROR/ MAINT LEDs Meaning Remedy RUN ERROR MAINT Off Off Off Supply voltage not present at interface module or too small Check the supply voltage or turn it on at the interface module. On On On Test of LEDs during startup: The three LEDs light up simultaneously for approxi- mately 0.25 s. --- Flashes Off Off Interface modu

• Siemens simatic ET 200MP, Documentation guide Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 7 General information The function manuals contain detailed descriptions on general topics regarding the SIMATIC S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web server, OPC UA. You can download the documentation free of charge from the Internet (http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual- overview/Pages/Default.aspx). Changes and supplements to the manuals are documented in a Product Information. You can download the product information free of charge from t

• Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 32 Manual, 11/2017, A5E03612323-AC 5.3.2 Maintenance events Triggering of a maintenance event The PROFINET interface of the interface module supports the diagnostic concept and maintenance concept in PROFINET according to the IEC 61158-6-10 standard. The goal

• Siemens simatic ET 200MP, Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 26 Manual, 11/2017, A5E03612323-AC Interrupts and diagnostic, error, and system alarms 5 5.1 Status and error displays Introduction Diagnostics by means of LED display is an initial tool for error localization. To further limit the error, you usually evaluate the display of the CPU, the display of the module status in STEP 7 or the diagnostics buffer of the CPU. The buffer contains plain text information on the error that has occurred. For example, you will find the number of the appropriate error OB there. LED display The figure below shows the LED display on the IM 155-5 PN ST interf

• Siemens simatic ET 200MP, Product overview 2.2 Functions Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 16 Manual, 11/2017, A5E03612323-AC Prioritized startup Prioritized startup denotes the PROFINET functionality for accelerating the startup of IO devices operated in a PROFINET IO system with RT communication. The function reduces the time that the correspondingly configured IO devices require to return to the cyclic user data exchange in the following cases: ● After the supply voltage has returned ● After a statio

• Siemens simatic ET 200MP, Technical specifications Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 42 Manual, 11/2017, A5E03612323-AC Article number 6ES7155-5AA01-0AB0 Ambient conditions Ambient temperature during operation • horizontal installation, min. 0 °C • horizontal installation, max. 60 °C • vertical installation, min. 0 °C • vertical installation, max. 40 °C Connection method ET-Connection • via BU/BA Send No Dimensions Width 35 mm Height 147 mm Depth 129 mm

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 33 5.3.3 Channel diagnostics Function Channel diagnostics provides information about channel faults in modules. Channel faults are mapped as channel diagnostic data in IO diagnostic data records. The "RDREC" instruction is used to read the data record. Structure of the diagnostic data records ● Firmware version V4.0 or higher: The IM 155-5 PN ST interface module maps channel faults by means of extended channel diagnostics

• Siemens simatic ET 200MP, Product overview 2.1 Properties Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 12 Manual, 11/2017, A5E03612323-AC Maximum configuration ● 512 bytes I/O data per station ● The integrated power supply of the interface module feeds 14 W into the backplane bus. Up to 12 I/O modules can be supplied this way. The exact number of operable modules is determined by the power budget (see relevant section in the ET 200MP distributed I/O system (https://support.industry.siemens.com/cs/ww/en/view/59191792) system manual). ● A maximum of one power supply module (PS) upstream from the interface module and two downstream from the interface mod

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 31 Reading out the diagnostic data Table 5- 3 Reading out the diagnostic data with STEP 7 Automation system with IO controller Application See... SIMATIC S7 Diagnostic data as plain text in STEP 7 using online view and diagnostic view Online help of STEP 7 and • as of STEP 7 V12 PROFINET with STEP 7 V12 function manual (http://support.automation.siemens.c om/W

• Siemens simatic ET 200MP, Interrupts and diagnostic, error, and system alarms 5.3 Alarms Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 36 Manual, 11/2017, A5E03612323-AC USI structure = W#16#0005 Table 5- 12 USI structure = W#16#0005 Data block name Contents Note Bytes USI W#16#0005 Manufacturer-specific diagnostic data if there is more than one bus master module (IM/CPU) 2 Followed by 4 reserved bytes Reserved 1 Reserved 1 Reserved 1 Reserved 1 USI structure = W#16#0006 Table 5- 13 USI structure = W#16#0006 Data block name Contents Note Bytes USI W#16#0006 Manufact

• Siemens simatic ET 200MP, Technical specifications Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 41 Article number 6ES7155-5AA01-0AB0 PROFINET IO Device Services – Isochronous mode Yes – IRT Yes – MRP Yes – MRPD No – PROFINET system redundancy No – PROFIenergy No – Prioritized startup Yes – Shared device Yes – Number of IO Controllers with shared device, max. 2 Open IE communication • TCP/IP Yes • SNMP Yes

• Siemens simatic ET 200MP, Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG GERMANY A5E03612323-AC Ⓟ 09/2017 Subject to change Copyright © Siemens AG 2013 - 2017. All rights reserved Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe pe

• Siemens simatic ET 200MP, Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 39 Technical specifications 6 Technical specifications of the IM 155-5 PN ST Article number 6ES7155-5AA01-0AB0 General information Product type designation IM 155-5 PN ST HW functional status FS01 Firmware version V4.1.0 Vendor identification (VendorID) 0x002A Device identifier (DeviceID) 0X0312 Product function • I&M data Yes; I&M0 to I&M3 Engineering with • STEP 7 TIA Portal configurable/integrated as of version V14 or higher

• Siemens simatic ET 200MP, Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) 4 Manual, 11/2017, A5E03612323-AC Preface Purpose of the documentation This manual supplements the system manual S7-1500, ET 200MP automation system (https://support.industry.siemens.com/cs/ww/en/view/59191792). Functions that generally relate to the system are described in this manual. The information provided in this manual and in the system/function manuals support you in commissioning the system. Conventions Please also observe notes marked as follows:

• Siemens simatic ET 200MP, Product overview 2.2 Functions Interface module IM 155-5 PN ST (6ES7155-5AA01-0AB0) Manual, 11/2017, A5E03612323-AC 13 2.2 Functions 2.2.1 PROFINET IO Introduction The interface module supports the following PROFINET IO functions: ● Integrated switch with 2 ports ● Supported Ethernet services: ping, arp, SNMP, LLDP ● Port diagnostics ● Disabling ports ● Isochronous real-time communication ● Minimum update time 250 μs ● Prioritized startup ● Device replacement without PG (LLDP) ● Media redundancy (MRP) ● Shared device with up to two IO controllers ● Module-internal Share

More Instructions:

	Siemens simatic ET 200MP Manual  23-09-2023 40	DOWNLOAD
	Siemens simatic ET 200MP Manual  02-08-2022 53	DOWNLOAD
	Siemens simatic ET 200MP Operation & user’s manual 10-08-2023 57	DOWNLOAD
	Siemens simatic ET 200MP Manual  14-12-2022 24	DOWNLOAD

Related Products and Documents (Recording Equipment):

Comparable Devices:

Similar Resources:

• Philips DVP2880 (3 pages) PhilipsDVD playerHDMI 1080pDVP2880Get sharper, clearer pictureswith HDMI 1080p upscalingYour dream player with flawless, true-to-life picture quality and the ability to play virtually any disc! The Philips DVD player DVP2880 delivers your movies and music entertainment experience.Bring audio and video to life• HDMI 1080p upscales to high definition for sh …

• Shure PSM200 (19 pages) Model PSM200 User Guide27C8792 (Rev. 1) Printed in U.S.A.©2008 Shure IncorporatedPSM®200Personal Monitor System User GuideGuide de l’utilisation du système de retour personnelPersonal Monitor System BedienungsanleitungGuía del usuario del sistema de monitoreo personalGuida all’uso del sistema di monitoraggio personaleManual do Usuário do Sistema de …

• Zoom Handy REcorder H1 (14 pages) H1HandyRecorderH1Quick Start GuideSafety and Operation Precautions must be read before using the unit.ZOOM CORPORATION4-4-3 Surugadai, Kanda, Chiyoda-ku, Tokyo 101-0062 JapanCopying or reproduction of this document in part or in whole without permission is prohibited.H1-5001-2www.zoom.co.jp …

• Roland BR-1180 (192 pages) Owner’s ManualOwner's Manual02900178 ‘03-6-5NThank you, and congratulations on your choice of the BOSSBR-1180/1180CD Digital Recording Studio.Before using this unit, carefully read the sections entitled:• USING THE UNIT SAFELY (page 2–3)• IMPORTANT NOTES (page 4–5)These sections provide important information concerningthe proper ope …

• ELECRAFT N-GEN (2 pages) Elecraft • www.elecraft.com • 831-662-8345 ELECRAFT N-GEN WIDEBAND NOISE GENERATOR Revision D, November 7, 2008 Copyright © 2008, Elecraft; All Rights Reserved Introduction The Elecraft N-gen is a wideband noise source that is useful for a variety of receiver alignment tasks. It can be used in conjunction with a software program s …

• Cisco Flex 7500 Series (126 pages) Cisco Systems, Inc.www.cisco.com Flex 7500 Wireless Branch Controller Deployment GuideLast Updated: August, 2016IntroductionThis document describes how to deploy a Cisco Flex 7500 wireless branch controller. The purpose of this document is to:• Explain various network elements of the Cisco FlexConnect solution, along with their communication flow.• Provi …

Comments, Questions and Opinions: