Manualios.com

Whirlpool WHAPSRO Installation And Operation Manual

  • WHAPSRO Water Filtration Systems
  • maFu7CE.Y3rFQ
  • Installation And Operation Manual
  • PDF / Adobe Acrobat Reader
  • 27

Whirlpool WHAPSRO Manual Online:

3.4, 1929 votes
Whirlpool WHAPSRO User Manual
Whirlpool WHAPSRO User Guide
Whirlpool WHAPSRO Online Manual

Text of Whirlpool WHAPSRO User Guide:

  • Whirlpool WHAPSRO, Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury, MN 55125 How to install, operate and maintain your Reverse Osmosis Drinking Water System Model WHAPSRO Do not return unit to store Installation and Operation Manual System tested and certified by NSF International against NSF/ANSI Standards 42 & 58. See performance data on pages 25 & 26 for details. If you have any questions or concerns when installing, operating or maintaining your reverse osmosis system, call our toll free number: 1

  • 2 TABLE OF CONTENTS Page Specifications & Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Inspect Shipm

  • Whirlpool WHAPSRO, 3 Specifications & Dimensions Supply water pressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-100 psi (280-689 kPa) Supply water temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-100 °F (4.5-37.7°C) M aximum total dissolved solids (TDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 ppm Maximum water hardness @ 6.9 pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 gp

  • Whirlpool WHAPSRO, 4 Packing List Parts Bag Bag Drain Adapter Bag Water Storage Tank Reverse Osmosis Assembly With Red, Yellow, Blue & Green tubes attached Reverse Osmosis Faucet Assembly Black Drain Tube Tank Connector FIG. 2 Nitrate/Nitrite Test Kit Water Supply Fitting Inspect Shipment Your Reverse Osmosis Drinking Water System is shipped complete in one carton. Remove all items f rom your shipping carton. C heck all items against the packing list below. Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded

  • 5 Typical Under Sink Installation All install parts included in package. Plan Your Installation FIG. 3 Drain Adapter for Reverse Osmosis W aste Water Storage Tank Sink Drain P-Trap Shutoff Valve Reverse Osmosis Assembly HOT COLD Cold Water Supply Outside Faucet (Hard Water) Soft, Cold Water Soft, Hot Water Outside Faucet (Hard Water) Water Heater Shutoff Valve H a rd Wa te r L in e Wa

  • Whirlpool WHAPSRO, 6 R ead through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system. Your Reverse Osmosis Drinking Water System can be installed under a sink or in a remote location. Typical remote sites are a laundry room or utility room. Review the location options below and determine where you are going to install your system. NOTE: For best system performance, the feed water to the system should be softened or have hard- ness less than 10 g

  • Whirlpool WHAPSRO, 7 Step A - Install Supply Water Fitting CHOOSE TYPE OF WATER FITTING TO INSTALL Cold Water Supply Connection (using compression fitting - not included) FIG. 6B Cold Water Shutoff Valve 1/4” compression fitting insert ferrule 1/4” green tubing to Reverse Osmosis inlet Cold Water Supply Connection (using included water supply fitting) 1/4” green tubing to Reverse Osmosis inlet FIG. 6 Cold Water Shutoff Valve cold water shutoff cold water line water supply fitting gasket C heck and comply with local plumbing codes as you plan, then install a cold water supply fitting. Refer to the Specifications page for supply water requirements. The fitting must provide a leak-tig

  • Whirlpool WHAPSRO, 8 Step B - Install RO Drain Under Sink INTRODUCTION A suitable drain point is needed for the drain water from t he Reverse Osmosis filter. You have two options: • Install the Drain Adaptor included with your unit As shown in Figures 7-9, the drain adaptor is i nstalled onto your sink’s drain pipe above the P-trap. This is normally used for under sink installations. • Use another existing drain in your home As shown in Figures 10 and 11, the drain tube from the RO filter runs directly to an open drain. This is often used for remote location installations. NOTE: An i

  • Whirlpool WHAPSRO, 9 INSTALL A REMOTE DRAIN POINT AND AIR GAP (Remote Location) Route the drain tubing to an existing drain in the house. A floor drain, laundry tub, standpipe, sump, etc. are suitable drain points. See Fig. 11. This type of drain is the preferred over the p-trap drain adapter. Always be sure to provide a 1-1/2” air gap between the end of the hose and the drain point. This will prevent water from backing up into the system. NOTE: Check your local plumbing codes. To install a remote drain point, complete the following steps:

  • Whirlpool WHAPSRO, 10 Step C - Install RO Filter Assembly The fitting on the supply tank may need to be tight- ened 7-8 full turns to get a good seal. Do not overtighten. INSTALL STORAGE TANK 1. Apply thread sealing tape (2 wraps clockwise) to the threads on the nipple at the top of the tank. See Fig 13. 2. Locate the tubing connector (shutoff valve). See Fig. 13. Tighten the tubing connector onto the tank nip- ple 7-8 full turns, being careful not to cross thread or overtighten. 3. Do not connect the tube at this time. This will occur later in the assembly. 4. Place the storag

  • Whirlpool WHAPSRO, 11 Step E - Install RO Faucet Y ou will need to select the location of the Reverse Osmosis Faucet. You have three options to choose f rom: • Use the existing sink top hole for the spray hose or soap dispenser (Must be 1-1/4” in diameter) • Drill a new hole in the sink • Drill a new hole in the countertop next to the sink 1. Determine where you are going to install your Reverse Osmosis Faucet. 2. Check to ensure the Reverse Osmosis faucet will mount flat against the mounting surface. SELECT LOCATION OF REVERSE OSMOSIS FAUCET MOUNTING HOLE 3 . Visually revi

  • 12 Step E: Install RO Faucet (cont.) BLACK TUBE 3/8” barb fitting for the black tube RED TUBE 1/4” barb fitting for the red tube BLUE TUBE 3/8” quick connect fitting for the blue tube Faucet INSTALL REVERSE OSMOSIS FAUCET 1. Locate and organize your RO faucet install parts. Refer to Fig. 14. 2. Snap the o-ring into the groove on the bottom of the base and slide the base onto the fauc

  • Whirlpool WHAPSRO, 13 Step F - Connect Tubes HOW TO CUT AND CONNECT THE TUBES Your Reverse Osmosis system includes push-in fittings for quick tubing connection. Review the following instructions before connecting the tubes in the next step. Failure to follow these instructions may lead to future leaks. Cut tubes to length 1. Use a sharp cutter or knife to cut the end of tubing. Always cut the tubing square. See Fig. 16. 2. Inspect the tube up to 1” from the end to be sure there are no nicks, scratches or other rough spots. If needed, cut the tubing again. See Fig. 16. Connect tubes 1. Push tubing through collet, until i

  • Whirlpool WHAPSRO, 14 Step F - Connect Tubes (cont.) NOTE: Tube colors match collet colors. Tubing Connector (Shutoff valve) Drain Adaptor Sink P– Trap 3/8” BLU E 1 /4 ” RE D 3 /8 ” Y E L L O W OPEN CLOSED 1/ 4” G R EEN HOT COLD Water Supply Fitting ROUTE YELLOW TUBE TO STORAGE TANK 1. Locate the yellow tube attached to the Reverse Osmosis filter assembly. 2. Remove shipping cap from the loose end of the yellow tube. Route yellow tube to the fitting on top of the storage tank. See Fig. 21. 3. Cut tube square and to length. See Fig. 16. 4. Do not connect at this time. This will occur in the sanitizing step. CONNECT GREEN TUBE TO COLD WAT

  • Whirlpool WHAPSRO, 15 Step G - Sanitize, Test and Purge System SANITIZE THE SYSTEM Sanitizing is recommended immediately after installa- tion of the Reverse Osmosis system. It’s also recom- mended after servicing inner parts. It is important that t he person installing or servicing the system have clean hands while handling inner parts of the system. Complete the following steps to sanitize the system. See Fig. 22. 1. Make sure that the water supply to the Reverse Osmosis system is off. 2. Open the Reverse Osmosis faucet. If the tank is not alread

  • Whirlpool WHAPSRO, 16 Step G - Sanitize, Test and Purge System (cont.) Storage Tank HOT COLD FIG. 23 Reverse Osmosis Faucet Kitchen Faucet PRESSURE TEST THE SYSTEM NOTE: Complete the sanitizing procedures on the preceding page before pressure testing. To pressure test the system, complete the following steps. 1. Open the water supply valve(s) that you closed before installing the Reverse Osmosis system. 2. Purge air from the plumbing by opening the sink faucet(s). Close faucet(s) when water runs smooth, with no spurting. 3. Pressure will start to build in the RO system. In about 2 hours check a

  • 17 HOW YOUR REVERSE OSMOSIS SYSTEM WORKS Introduction: Your Reverse Osmosis (RO) Drinking Water System uses your household water pressure to force water through three filters. Impurities are filtered out. Delicious tasting drinking water goes to the stor- age tank-ready for your use. Impurities are sent down the drain. The following paragraphs will explain in detai

  • Whirlpool WHAPSRO, 18 How Your RO Water System Works 1 3 4 5 6 7 8 PRODUCT WATER Air Gap PRODUCT WATER FAUCET DRAIN WATER WATER IN Gravity Drain BL ACK BLUE GREEN RED YELLOW PREFILTER POSTFILTER Check Valve Drain Flow Control AUTOMATIC SHUTOFF RO MEMBRANE PRODUCT WATER STORAGE 2 Water Flow Description 1. Water enters prefilter. Sand, silt and other sediments are reduced. Chlorine is also reduced. See Fig. 24. 2. Water leaves prefilter and proceeds to the Reverse Osmosis Cartridge. 3. Water enters the Reverse Osmosis membrane. Dissolved solids are reduced. 4. Processed water leaves the Reverse Osmosis Membrane and

  • Whirlpool WHAPSRO, 19 Maintenance PREFILTER / POSTFILTER MAINTENANCE NOTE: It is recommended to replace the prefilter and postfilter cartridges at least every 6 months of product water use. Replace more often if they begin to plug with sediment. The prefilter and postfilter are replaceable sediment cartridges with activated carbon in their composition. See Fig. 25. You must periodically replace the prefilter and postfilter cartridge. This will protect the RO mem- brane from being destroyed by chlorine. It will also pre- vent the filters from plugging with sediment. You may notice a slower output of pr

  • 20 Maintenance CHANGE COLLET AND O-RING 1. Remove the collet and o-ring from the fitting with a small screwdriver. Do not scratch the internal walls of the collet port. See Figs. 26 & 27. 2 . Clean collet port, lubricate with silicone-based lubricant, and insert the o-ring seal into the bottom of the port. See Figs. 26 & 27. 3. Push the collet inward

  • Whirlpool WHAPSRO, 21 Troubleshooting P roblem: Chlorine taste and/or odor in the RO product water. Cause: The level of chlorine in your water supply exceeds maximum limits, and has destroyed the Reverse Osmosis mem- b rane. Correction: If the water supply contains more than 2.0 ppm of chlorine, addition- al filtering of the water supply to the Reverse Osmosis is needed. Contact your local water supplier. Correct this condition before doing m aintenance on the Reverse Osmosis system. Cause: The prefilter is no longer removing chlo- r ine from the water supply. Correction: Replace the prefilter, postfilter and Reverse Osmosis membrane c artridges. See Page 19. Problem: Other taste and/or odor.

  • Whirlpool WHAPSRO, 23 Ù Please purchase replacement cartridges from the retailer where you bought your reverse osmosis system. ¢ Not illustrated. = Not included. p Tubing lengths for remote installations, direct replacement for colored lengths of tubing. Parts List Key No. Part No. Description – 7 333145 Automatic Shutoff Kit (incl. Key No. 3, 4 of Key No. 2 & 6 of Key No. 1) 1 á Screw (6 req.) 2 á Washer (4 req.) 3 á Automatic Shutoff Cover Assembly – 7333137 Check Valve Kit (includes Key No. 4 & 2 of Key No. 5) 4 á Check Assembly 5 á O-ring, Auto. Shutoff Cover (2 req.) – 7333179 Diaphragm Kit (includes Key Nos. 7, 8 & 2

  • Whirlpool WHAPSRO, 24 EXTEND YOUR WARRANTY: Register your Whirlpool ® replacement filter and R.O. membrane purchases You can turn your R.O. system’s one year factory warranty into a lifetime warranty by registering your purchases of Whirlpool ® replacement R.O. membrane and filter cartridges. See “Lifetime Warranty” below for details. WARRANTY REVERSE OSMOSIS WATER FILTRATION SYSTEM - MODEL WHAPSRO (not including filter cartridges and R.O. membrane) Warrantor: Ecodyne Water Systems, 1890 Woodlane Drive, Woodbury, MN 55125 T wo Year Warranty: Warrantor guarantees, to the original owner that, when installed by a Lowes Professional Series installer,*

  • Whirlpool WHAPSRO, 25 Performance Data Reverse Osmosis Filter System - Model WHAPSRO IMPORTANT NOTICE: Read this performance data and compare the capabilities of this unit with your actual water treatment needs. It is recommended that, before purchasing a water treatment unit, you have your water supply tested to determine your actual water treatment needs. This filter system is designed to be used for the reduction of the substances listed below. Do not use where water is microbiologically unsafe or of unknown quality, without ade- quate disinfection before or after the sys

  • Whirlpool WHAPSRO, 26 Performance Data PERFORMANCE CLAIMS FOR WHAPSRO S ubstance NSF Required Influent Challenge Concentration (mg/L) 1 NSF Max. Per - missible Product Water Concen - tration (mg/L) 1 Average I nfluent (mg/L) 1 Avg. / Max. E ffluent (mg/L) 1 Avg. / Min. P ercent Reduction Arsenic (pentavalent) 2 0.30 ±10% 0.010 0.320 0.006 / 0.011 98.2 / 96.6 Barium 2 10 ±10% 2.0 10 0.23 / 0.58 97.8 / 94.4 Cadmium 2 0.03 ±10% 0.005 0.028 0.0005 / 0.0012 98.1 / 95.7 Chromium (VI) 2 0.3 ±10% 0.1 0.310 0.009 / 0.017 97.0 / 94.4 Chromium (I

  • Whirlpool WHAPSRO, 27 Performance Data ARSENIC FACTS Background A rsenic (abbreviated As) can occur naturally in well water. There are two forms of arsenic: pentavalent arsenic [also called As (V), As (+5), and arsenate] and trivalent arsenic [also called As (III), As (+3), and arsenite]. Although both forms are potentially harmful to human health, trivalent arsenic is considered more harmful than pentavalent arsenic. In well water, arsenic may be pentavalent, trivalent, or a combination of both. Additional information about arsenic in water can be found on the Internet at the U.S. Environmental Protection Agency (USEPA) website:www.epa.gov/safewater/arsenic.html. Testing Your

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Trust PW-1290p Operation & user’s manual trust/pw-1290p-V57.pdf 23 Sep 2022 1 1.97 Mb
2 Electrolux XBEF10AS Brochure & specs electrolux/xbef10as-789.pdf 09 Jan 2024 4 0.27 Mb
3 Hotsy 965SS Operating instructions and parts manual hotsy/965ss-SM5.pdf 19 Sep 2023 38
4 Toshiba A305D-S6886 Specifications toshiba/a305d-s6886-V47.pdf 30 Jul 2023 4 0.06 Mb
5 2N EasyRoute Operation & user’s manual 2n/easyroute-242.pdf 13 Oct 2022 33
6 Bosch TCA6001 Operating instructions manual bosch/tca6001-81R.pdf 09 Dec 2023 130

Similar Resources:

  • Virginio Nastri

    SAV 1 Series

    (15 pages)
    VIRGINIO NASTRI srl Via Seconda Strada,161 – Z.I. - 36071 ARZIGNANO (VI) ITALY Tel. ++39-0444 450 620 - ++39-0444 651 520 – Fax ++39-0444 671 840 E-mail: [email protected] - Web Site: www.virginionastri.com VIBRATION SEPARATOR SAV 1 Series User and maintenance manual …
  • BWT

    AKF 300

    (34 pages)
    AktivkohlefilterActivated carbon filterFiltre à charbons actifsFiltro de carbón activoFiltro a carbone attivoActieve-koolstoffilterAKF 300, AKF 4001-505707 / 9108 A / 10.2005 / © BWTWassertechnik GmbH / Printed in GermanyEinbau- und Bedienungsanleitung DInstallation and operating manual GBInstructions de montage et d'utilisation FInstrucciones de mon …
  • Sepura

    SEP 60 ST

    (2 pages)
    SEP 60 STSingle Use Condensate Cleanerwww.sepura-technologies.cominstallation manualinstallation1Before Starting Assembly, pleaseread the following:SEP 60 ST is a single-use product. It shouldbe replaced as directed to ensure its vitalenvironmental and legally protectivefunctions are performed correctly.SEP 60 ST has been designed to cleancondensate from a c …
  • Omnifilter

    OM26KCS

    (64 pages)
    OM26KCS, OM32KCS, OM36KCSWater Softening SystemINSTALLATION INSTRUCTIONS English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2-22Repair Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13OM26KCS, OM32KCS, OM36KCSSistema de ablandamiento de aguaINSTRUCCIONES DE INSTALACIÓN Español . . . . . . . . . . . . . . . . . . . …
  • Lenze

    L-force 9400 Series

    (108 pages)
    EDB94Axx6954.AtdÄ.AtdäInbetriebnahme−LeitfadenCommissioning guideGuide de mise en serviceGuía para la puesta en marchaGuida per la messa in servizio9400 1.5 ... 695 AlE94ASHExxxx Single Drive HighLineE94AMHExxxx Multi Drive HighLineAchsmodulAxis moduleModule d’axeMódulo de ejeModulo asseL−force Drives …
  • SpectraPure

    The Eliminator DI

    (12 pages)
    SpectraPureSpectraPure®Inc. 480.894.5437 Call us toll-free 1.800.685.2783 215 South Industrial Drive, Suite 2A Tempe, Arizona 85281-2941®24One Year Limited WarrantySpectraPure, Inc. warrants each new Reverse Osmosis system to the original owner only to be free of defects in material and workmanship for a period of one year from the date of rec …

Comments, Questions and Opinions: