Manualios.com

Whirlpool WHES40 Installation And Operation Manual

  • WHES40 Water Dispenser
  • maFu7CE.Y3rFQ
  • Installation And Operation Manual
  • PDF / Adobe Acrobat Reader
  • 18

Whirlpool WHES40 Manual Online:

4.2, 2882 votes
Whirlpool WHES40 User Manual
Whirlpool WHES40 User Guide
Whirlpool WHES40 Online Manual

Text of Whirlpool WHES40 User Guide:

  • Whirlpool WHES40, Whirlpool Model WHES40 Model WHES44 Model WHESCS Water softener Installation and operation manual * How to install, operate and maintain your Demand Controlled Water Softener Our industry refers to this unit configuration as a tank in tank unit. In Arizona the salt can stick to the resin tank. We call this problem a ‘salt bridge’. Salt bridges are very inconvenient. Specifications & Performance Claims These models are efficiency rated. The efficiency rating is valid only at the minimum salt dose and rated service flow. These so

  • Whirlpool WHES40, rated salt efficiency is measured by laboratory tests described in NSF/ANSI Standard 44. These tests represent the maximum possible efficiency that the system can achieve. Operational efficiency is the actual efficiency after the system has been installed. It is typically less than the rated efficiency, due to individual application factors including water hardness, water usage, and other contaminants that reduce a softener’s capacity. Model WHES40 Model WHES44 Model Code LL40 LL44

  • Ferric (red water), and bacterial and organically bound irons are insoluble. This water softener will not remove ferric or bacterial iron. This iron is visible immediately when drawn from a faucet because it has oxidized before reaching the home. It appears as small cloudy yellow, orange, or reddish suspended particles. After the water stands for a period of time, the particles settle

  • Whirlpool WHES40, Light flashing rapidly, with “CURRENT TIME” shown in the display and the clock flashing slowly – The present time needs to be set, either during initial start up or after a long power outage. See “Set Time of Day”, at right. Light flashing rapidly, with “Err” shown in the display – The electronic self-diagnostics have detected a problem. See “Troubleshooting” on Page 18. Light on steady (not flashing) – The system has power applied and does not require any attention. When the power supply is plugged into the electrical outlet, the model code (�

  • Whirlpool WHES40, If you want to change the recharge start time, press the UP or DOWN buttons until the desired time shows. Be sure AM or PM is correct. SET SALT TYPE Press the PROGRAM button once again to display a flashing “nACL”. Salt Type allows you to choose between sodium chloride (NaCI), which is regular softener salt, or potassium chloride (KCI), which is an alternative to sodium chloride. KCI (potassium chloride) may be used if the user of the water softener is on a sodium restricted diet and is c

  • Whirlpool WHES40, The softener enters the fill cycle of regeneration right away. “RECHARGE” will flash during the regeneration. When completed, full water conditioning capacity is restored. While water softener is running a recharge, the time remaining until the recharge is completed will show in the display during all cycles except for the Fill cycle. NOTE: Avoid using hot water while the softener is regenerating, because the water heater will refill with bypass hard water. RECHARGE SCHEDULED If you do not want to start an immediate recharge, but would like to schedule an extra recharge at the next preset recharge time, do the following: Press and r

  • Whirlpool WHES40, button again will turn the light off. The tank light will automatically turn off after a period of 15 minutes if the tank light button is not used to turn it off. Customizing Features I Options POWER OUTAGE MEMORY If electrical power to the water softener is lost, “memory” built into the timer circuitry will keep all settings for several hours. While the power is out, the display is blank and the water softener will not regenerate. When electrical power is restored, the following will occur: Reset the present time only if the display is flashing. The HARDNESS and RECHARGE TIME

  • Press the PROGRAM button three times to return to the normal run display. MAXIMUM DAYS BETWEEN REGENERATIONS The water softener automatically controls regeneration frequency. This provides the greatest operating efficiency and, under most conditions, this feature should be left in this automatic mode. However, you may modify this feature if you want to force a regeneration every se

  • Whirlpool WHES40, NOTE: In humid areas, it is best to keep the salt storage level lower, and to refill more often to avoid salt “bridging”. Recommended Salt: Nugget, pellet or coarse solar salts with less than 1% impurities. Salt Not Recommended: Rock salt, high in impurities, block, granulated, table, ice melting, ice cream making salts, etc. BREAKING A SALT BRIDGE Sometimes, a hard crust or salt “bridge” forms in the brine tank. It is usually caused by high humidity or the wrong kind of salt. When the salt “bridges,” an empty space forms between the water and the salt. Then, salt will not dissolve in the water to make brine. Without brine, the resin b

  • Whirlpool WHES40, Words in picture: 0-ring Seal; Screen Support; Screen; Nozzle & Venturi Disc; Plug; Gasket; Cone Screen; Flow Plug (HVDC) ;Housing; Ferrule *Install with lettered side up, concave Nut side down. IMPORTANT: Be sure small hole in the gasket is centered directly over the small hole in the nozzle & venturi housing. Be sure the numbers are facing up To get access to the nozzle & venturi, remove the water softener’s top cover. Put the bypass valve(s) into the bypass position. Be sure the water softener is in soft water (service) cycle (no water pressure at nozzle & venturi). Then, holding the nozzle & venturi housing with one hand, unscrew the cap. Do not los

  • Err I While an error code appears in the display, all buttons are inoperable except the PROGRAM button. PROGRAM remains operational so the service person can perform the Manual Advance Diagnostics, see below, to further isolate the problem. Procedure for removing error code from display: Unplug power supply from electrical outlet. Correct problem. Plug pow

  • Whirlpool WHES40, While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is retained by the computer from the first time electrical power is applied to the electronic controller. Press the UP button to display the number of days this electronic control has had electrical power applied. Press the DOWN button to display the number of regenerations initiated by this electronic control since the code number was entered. Press and hold the PROGRAM button until the model code (“LL40” for Model WHES40 or “LL44” for Model WHES44) shows i

  • Whirlpool WHES40, If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe. After observing fill, press the RECHARGE button to move the softener’s valve into the brine position. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level. This may take 15 to 20 minutes. NOTE: Be sure water is in contact with the salt, and not separated by a salt bridge (See “Breaking A Salt Bri

  • Whirlpool WHES40, Softener Parts List Key No Part No. Description – 7112963 Distributor 0-Ring Kit (includes Key Nos. 1-3) I same 0-Ring, 2-7/8″ x 3-1/4″ 2 same 0-Ring, 13/16″ x 1-1/16″ 3 same 0-Ring, 2-3/4″ x 3″ 4 7077870 Top Distributor 5 7105047 RepI. Bottom Distributor – 7331177 Tank Neck Clamp Kit (includes 2 ea. of Key Nos. 6 & 7) 6

  • 12 7337482 Power Supply, 28V DC 13 7335163 RepI. Electronic Control Board (PWA) 14 7267116 Top Cover & Faceplate Assembly, (order decal below) 7335553 Faceplate Decal Key No. Part No. Descri

  • Whirlpool WHES40, Valve Parts List Key No. Part No. Description 100 7224087 Screw, #8-32 x 1″ (2 req.) 101 7286039 Motor (incl. 2 ea. of Key No. 100) 102 7231393 Motor Plate 103 0900857 Screw, #6-20 x 3/8″ (3 req.) 104 7171250 Bearing 105 7283489 Cam & Gear – 7331169 Drain Hose Adaptor Kit (includes Key Nos. 106-110) 106 same Clip, Drain 107 same Hose Clamp 1

  • Whirlpool WHES40, 113 same 0-Ring, 4-1/2″ x 4-7/8″ 114 same Rotor Seal 115 same Seal 116 same Seal, Nozzle & Venturi 117 7174313 Bearing, Wave Washer 118 7185500 Rotor& Disc – 7342712 Drain Plug Kit, 1″ 119 same Plug, Drain Seal 120 same Spring 121 7337589

  • Whirlpool WHES40, 134 7114533 Nozzle & Venturi Gasket Kit 7204362 Gasket Only 135 7084607 Flow Plug, .15 gpm 136 7146043 Screen 137 7167659 Screen Support 138 7170262 0-Ring, 1-1/8″ x 1-3/8″ 139 7199729 Cap 140 7175199 Wave Washer 141 7171161 Valve Cover 142 7342681 Screw, #10 x 2-5/8″, pack

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Hama USB 2.0 Repeater Operation & user’s manual hama/usb-2-0-repeater-234.pdf 17 May 2023 2 0.06 Mb
2 HP 4310s - ProBook - Core 2 Duo 2.1 GHz Manual  hp/4310s-probook-core-2-duo-2-1-ghz-652.pdf 19 Apr 2023 38 1.03 Mb
3 Hotpoint MG23N/H Instruction booklet hotpoint/mg23n-h-C63.pdf 01 Feb 2024 44 2.21 Mb
4 Western Digital My Net AC1300 Installation manual western-digital/my-net-ac1300-2DE.pdf 28 Feb 2023 6
5 Fortinet FortiGate-5001C Manual  fortinet/fortigate-5001c-2HS.pdf 23 May 2023 36 1.57 Mb
6 Weslo Pursuit 310 Cs Operation & user’s manual weslo/pursuit-310-cs-X73.pdf 28 Aug 2022 16 0.86 Mb

Similar Resources:

  • Watts

    OneFlow OF744-10

    (22 pages)
    Installation, Operation and Maintenance ManualOneFlow® Anti-Scale SystemChemical-Free, Salt-Free Scale PreventionModel OF744-10Model OF844-12Model OF948-16Model OF1054-20Model OF1252-30IntroductionThe Watts OneFlow® system provides protection from scale formation throughout the plumbing system. The OneFlow® system can be installed at the point of entry to …
  • Miele

    PG 8090

    (68 pages)
    de Gebrauchsanweisung - Monoenthärter PG 8090en Operating instructions - Monoblock water softenerPG 8090fr Mode d’emploi - L'adoucisseur PG 8090it Istruzione d’uso - Depuratore monobloccoPG 8090es Instrucciones de manejo - MonodescalcificadorPG 8090pt Instruções de utilização - Descalcificador PG 8090nl Gebruiksaanwijzing - Mono-ontharder PG 80 …
  • Karcher

    WPD 100

    (316 pages)
    Register and win!www.kaercher.comWPD 10059643200 04/12Deutsch 3English 14Français 25Italiano 36Nederlands 47Español 58Português 69Dansk 80Norsk 91Svenska 102Suomi 113Ελληνικά 124Türkçe 136Русский 147Magyar 159Čeština 170Slovenščina 181Polski 192Româneşte 203Slovenčina 214Hrvatski 225Srpski 236Български …
  • Elba

    ETP-F5082

    (10 pages)
    THERMO POT MODEL: ETP-F5082(BR) Owner’s Manual Please read this manual carefully before operati …
  • SPM

    NINO

    (63 pages)
    Data di emissione: Gennaio, 2016 Revisione: 1 Pag. : 1/63 NINO Manuale d’uso e manutenzione Pag.2 Operator’s manual Page 21 Betriebs- und Wartungsanleitung Seite 40 …
  • Coway

    P-07IU

    (40 pages)
    WaterFiltration Device P-07IU• For your safety and proper use of the product, please read this User’s Manual before use.• Warranty card is included in this User’s Manual. …

Comments, Questions and Opinions: