Manualios.com

Siemens SIDOOR ATE500E System Manual

Siemens SIDOOR ATE500E Manual Online:

4, 1774 votes
Siemens SIDOOR ATE500E User Manual
Siemens SIDOOR ATE500E User Guide
Siemens SIDOOR ATE500E Online Manual

Text of Siemens SIDOOR ATE500E User Guide:

  • Siemens SIDOOR ATE500E, Controller 6.6 Connecting terminals and interfaces ATE500E 72 System Manual, 09/2017, A5E33917696-AD Slot X11 X15 X16 Connector PHOENIX 1803594 RJ45 Cat. 5 PHOENIX 1803581 SZS 0.4x2.5 - SZS 0.4x2.5 1x0.14 - 1.5mm 2 - 1x0.14 - 1.5mm 2 1x0.14 - 1.5mm 2 - 1x0.14 - 1.5mm 2 AWG 30 - 14 - 30 - 14 Nm 0.22 - 0.25 - 0.22 - 0.25 7 mm - 7 mm L > 30m L > 30m L > 30m Task The CAN module enables the SIDOOR ATE500E door controller to be connected to a CAN bus. A maximum of 32 nodes can be connected to the CAN bus.

  • Siemens SIDOOR ATE500E, Table of contents ATE500E System Manual, 09/2017, A5E33917696-AD 5 6.4 Operation and parameter assignment .................................................................................... 42 6.4.1 Overview of parameter assignment options ........................................................................... 42 6.4.2 Service buttons / Minimal editor .............................................................................................. 42 6.4.2.1 Service buttons ....................................................................................................................... 43 6.4.2.2 Minimal editor ......................................

  • Siemens SIDOOR ATE500E, Controller 6.10 Technical specifications ATE500E System Manual, 09/2017, A5E33917696-AD 87 Article number 6FB1211-5AT10-7AT2 6FB1211-1AT10-7AT3 Digital inputs Control inputs isolated Yes Control inputs p-switching Yes Input voltage • per DC input, min. 10 V; Observe polarity ! • per DC input, max. 28 V; Observe polarity ! Input current • per DC input, min. 3 mA • per DC input, max. 15 mA Digital outputs Relay outputs Switching capacity of contacts – at 30 V DC, min. 0.01 A – at 30 V DC, max. 1 A 0.5 A – at 50 V D

  • Siemens SIDOOR ATE500E, Controller 6.4 Operation and parameter assignment ATE500E System Manual, 09/2017, A5E33917696-AD 49 Setting the closing forces 1. Press the learn run button (S401) to set the closing forces. 2. The LED display alternates between displaying an "A" and the currently set counterweight in the form of a number from 0 to 6. 3. Select the desired counterweight (0 to 6) by pressing the service button S402 (downwards) or S403 (upwards). Note The closing forces are set in the form of a counterweigh t. The calculation uses the simplified ratio of 1 kg to 10 N. The input ranges from 0 to 6, where 0 stands for "no count

  • Siemens SIDOOR ATE500E, Controller 6.4 Operation and parameter assignment ATE500E 50 System Manual, 09/2017, A5E33917696-AD 6.4.3 Operating options via additional units Description In addition to the parameter assignment options integrated in the controller, parameters can also be assigned to the SIDOOR controller via the following additional units. ● SIDOOR USER SOFTWARE The SIDOOR User Software is part of the SIDOOR SOFTWARE KIT. You can find a detailed description of the SIDOOR SOFTWARE KIT in the SIDOOR SOFTWARE KIT Operating Instructions (http://support.automation.siemens.com/WW/view/en/92711247). ● SIDOOR SE

  • Siemens SIDOOR ATE500E, ATE500E 20 System Manual, 09/2017, A5E33917696-AD Application 4 The comfort SIDOOR ATE500E elevator door drive is an "intelligent" door drive that can open and close cabin and shaft doors at adjustable speeds, accelerations and with adjustable forces.

  • Siemens SIDOOR ATE500E, Product family 3.2 Products ATE500E System Manual, 09/2017, A5E33917696-AD 17 3.2.4 Power supply ① SIDOOR TRANSFORMER ② SIDOOR TRANSFORMER UL ② SIDOOR NT40 SIDOOR power supplies connect the controllers to the respective application-specific power supply. Device selection Product Article No. Description SIDOOR NT40 6FB1112-0AT20-3PS0 Power supply for controllers without an integrated power supply unit. SIDOOR TRANSFORMER 6FB1112-0AT20-2TR0 SIDOOR TRANS

  • Power supply 8.3 SIDOOR TRANSFORMER ATE500E 122 System Manual, 09/2017, A5E33917696-AD 8.3.3 Connection Requirements WARNING Dangerous electrical voltage! When electrical devices are operated, parts of these devices will necessarily carry dangerous voltages. Failure to observe the operating instructions can therefore lead to serious injuries or material dama

  • Siemens SIDOOR ATE500E, Appendix A.1 Profiles and adjustment ranges ATE500E System Manual, 09/2017, A5E33917696-AD 149 A.1.2 MED280 profile Table A- 1 SIDOOR MED280 profiles valid for the SIDOOR ATE500E controller Parameter Unit Profile 1* Profile 2 Profile 3 Profile 4 Profile 5 Profile 6 Creep distance OPEN mm 30 20 20 30 30 30 Cutter distance OPEN mm 50 30 30 40 40 40 Creep distance CLOSE mm 0 0 0 0 0 0 Cutter distance CLOSE mm 60 40 40 60 60 40 Maximum speed OPEN mm/s 700 4

  • Siemens SIDOOR ATE500E, Power supply 8.2 SIDOOR NT40 ATE500E 108 System Manual, 09/2017, A5E33917696-AD 8.2 SIDOOR NT40 8.2.1 Description Intended use The device has been designed for operation exclusively in an industrial environment, and may only be operated in conjunction with the controllers listed in Product combinations (Page 21). Other loads must not be connected to the output connector X2. Note Electromagnetic compatibility The SIDOOR NT40 power supply meets the r equirements of the EMC standard EN 61000-6- 4. The SIDOOR NT40 power supply can cause interference if used in a residential environment. The commissioning eng

  • Siemens SIDOOR ATE500E, Motor 7.2 Installation ATE500E System Manual, 09/2017, A5E33917696-AD 93 Procedure WARNING Risk of injury and damage to property as a result of incorrect installation Improper and incorrect installation can lead to serious injuries. Observe the instructions for safe installation.

  • Siemens SIDOOR ATE500E, ATE500E 4 System Manual, 09/2017, A5E33917696-AD Table of contents 1 Introduction ............................................................................................................................................. 7 2 General safety instructions ...................................................................................................................... 9 3 Product family ....................................................................................................................................... 12 3.1 Overview .....................................................................

  • Siemens SIDOOR ATE500E, Motor 7.5 Technical specifications ATE500E 100 System Manual, 09/2017, A5E33917696-AD Accessories SIDOOR motor holder Order number 6FB1104-0AT03-0AD0 General technical data: product brand name SIDOOR Product designation Motor support Design of the product for SIDOOR motor MED280 SIDOOR motor mounting bracket Order number 6FB1104-0AT01-0AS0 General technical data: product brand name SIDOOR Product designation mounting bracket Design of the product for rubber-bonded metal mounting Installation/ mounting/ dimensions: Width of mounting bracket mm 90 Height of mounting

  • Motor 7.5 Technical specifications ATE500E System Manual, 09/2017, A5E33917696-AD 101 SIDOOR deflector unit Order number 6FB1104-0AT07-0AS0 General technical data: product brand name SIDOOR Product designation deflector unit Design of the product with deflector pulley Installation/ mounting/ dimensions: Width of the support in

  • Siemens SIDOOR ATE500E, Controller 6.2 Drive functions ATE500E 32 System Manual, 09/2017, A5E33917696-AD 6.2.12 Oscillation protection The oscillation protection prevents permanent oscillation of the door at the end stop. End position "open" If the system is pressed out of the end position with the drive order "open" present, the system detects that the "open" position has been left, and attempts to return to the end stop with the set static opening force. After reaching the end stop, the drive is pressed against t

  • Siemens SIDOOR ATE500E, Power supply 8.4 SIDOOR TRANSFORMER UL ATE500E System Manual, 09/2017, A5E33917696-AD 133 8.4.4 Test voltage Figure 8-8 Diagram test voltage The type test and the manufacturing test can only be performed by the manufacturer. The field can also be performed by the user. Requirements for performing the field test: General Disconnect SIDOOR TRANSFORMER from the power supply by pulling out the power plug, disconnect the connection to the SIDOOR control circuit device. Inspection (A) & (B) ● Interconnecting input lines (PRI) L1 and L2/N ●

  • Siemens SIDOOR ATE500E, Product family 3.1 Overview ATE500E System Manual, 09/2017, A5E33917696-AD 13 Overview of the product family Figure 3-1 System setup EC technology The ATE500E controller supports three-phase EC motors.

  • Siemens SIDOOR ATE500E, Controller 6.6 Connecting terminals and interfaces ATE500E 74 System Manual, 09/2017, A5E33917696-AD Wiring and connecting DANGER Risk of injury due to electrical voltages The protective cover has to be removed to connect the CAN cable or to activate/deactivate the terminating resistor. Perform the following protective measures before removing the protective cover: • Disconnect the controller from all live cables. • By grounding, ensure that the user/fitter, the controller and other conductors have the same voltage p

  • Siemens SIDOOR ATE500E, ATE500E 12 System Manual, 09/2017, A5E33917696-AD Product family 3 3.1 Overview SIDOOR Door control system is the general term for a controller of an access system. The SIDOOR product family is primarily intended for operating sliding doors. Door control systems are characterized by the fact that there are always two defined states: namely for the open and closed positions of the door. The door is always controlled between these two positions in accordance with the guidelines. In a

  • Controller 6.6 Connecting terminals and interfaces ATE500E System Manual, 09/2017, A5E33917696-AD 61 Table 6- 6 Properties of slots and interfaces Slot X3 X4 X6 Connector WAGO 721-103/026- 045 PHOENIX 1792757 PHOENIX 1792799 SZS 0.6x3.5 SZS 0.6x3.5 SZS 0.6x3.5 1x1.5 - 2.5mm 2 1x0.2 - 2.5mm 2 1x0.2 - 2.5mm 2 1x1.5 - 2.

  • Controller 6.9 Diagnostics ATE500E 84 System Manual, 09/2017, A5E33917696-AD Display Description Fault resolution E Motor overvoltage • Check the input voltage of the controller at the power supply connector X3: The maximum supply voltage permitted for the controller is 36 V +3%. • Check the line voltage. • Check the power supply and rep

  • Siemens SIDOOR ATE500E, Controller 6.6 Connecting terminals and interfaces ATE500E 62 System Manual, 09/2017, A5E33917696-AD 6.6.2 Digital input signals Slot X6 You can connect the following signals for drive functions of the ATE500E controller to the LIGHT BARRIER / DCPS, NUDGING, CLOSE and OPEN inputs of the terminal X6: Table 6- 7 Overview of signals for drive functions at slot X6 Slot X6 Drive functions LIGHT BARRIER / DCPS Light barrier (Page 24) or DCPS (Door Closed Position Sensor) (Page 25) NUDGING Nudge (Page 26) CLOSE DOOR CLOSE (command given via digital inputs) (Page 27) OPEN DOOR OPEN (comman

  • Siemens SIDOOR ATE500E, ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ Automatic Door Controls SIDOOR ATE500E System Manual 09/2017 A5E33917696 -AD Introduction 1 General safety instructions 2 Product family 3 Application 4 Product combinations 5 Controller

  • Siemens SIDOOR ATE500E, Controller 6.2 Drive functions ATE500E System Manual, 09/2017, A5E33917696-AD 29 6.2.8 Overload protection Description of function If the drive motor or controller are subject to high loads, an automatic overload protection function will activate, based on the temperature of the motor or controller. The overload protection initially reduces the drive parameters. If a specific maximum temperature is exceeded, the motor is deenergized when at a stop, and executes no further drive commands until the temperature has fallen. "4" is shown on the 7-segment display (H401) while the overload pro

Related Products and Documents (DC Drives):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 HP Presario All-in-One CQ1-2100 Setup poster hp/presario-all-in-one-cq1-2100-61Q.pdf 13 Oct 2022 1 3.6 Mb
2 High Tech Pet Bluefang BF-22 Instruction manual high-tech-pet/bluefang-bf-22-WDA.pdf 22 Jan 2023 32
3 North Star 47500 Owner's manual north-star/47500-65F.pdf 11 May 2023 35
4 Frigidaire FFU14F5HW - 13.7 cu. Ft. Frost Free Upright Freezer Product specifications frigidaire/ffu14f5hw-13-7-cu-ft-frost-free-upright-freezer-N9B.pdf 11 Nov 2022 2 0.29 Mb
5 Weeview SID WV3000 Operation & user’s manual weeview/sid-wv3000-3B1.pdf 25 Oct 2022 10
6 Nextar X3i Quick start nextar/x3i-73V.pdf 03 Aug 2023 1

Similar Resources:

  • Eurotherm

    584SV Series

    (255 pages)
    (8527+(50'5,9(68;769#6HULHV)UHTXHQF\,QYHUWHU3URGXFW#0DQXDO+$79694:8334##,VVXH#5#&RS\ULJKW#(XURWKHUP#'ULYHV#/LPLWHG#4<<<All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form orby any means to persons not employed by a Eurotherm group company without written permission f …
  • Santerno

    SINUS H

    (97 pages)
    • 15G0176B100 • SINUS H VARIABLE FREQUENCY DRIVE USER MANUAL - Extension I/O Module - Issued on 13/04/16 R.00 Software Version 32.41 • This manual is integrant and essential to the product. Carefully read the instructions contained herein as they provide important hints for use and maintenance safety. • This device i …
  • IMMOOS

    SS1 oGB

    (28 pages)
    Operating instructions1-person evacuation systemfor fixed and detachable ropewaysThe 1-person evacuation system is compatible with the self-driven carriage Type SS1 mGB / Typ SS1 oGB / Typ SS1 Twin mGB / Typ SS2 mGB.Corresponds to the today‘s valid, European harmonized CEN standards and the regulation (EU) 2016/424 „cableway installation“ and is addi …
  • HAUTAU

    HS

    (72 pages)
    HAUTAULIFT&SLIDE HARDWAREMOUNTING INSTRUCTIONSHS comfort drive Timber, Timber-Alu coveredHAUTAU, a MACO Group companyOnly for use by certied specialists!TIMBERALU …
  • Parker

    Gemini GT6 Series

    (81 pages)
    Artisan Technology Group is your source for quality new and certied-used/pre-owned equipment• FAST SHIPPING AND DELIVERY• TENS OF THOUSANDS OF IN-STOCK ITEMS• EQUIPMENT DEMOS• HUNDREDS OF MANUFACTURERS SUPPORTED• LEASING/MONTHLY RENTALS• ITAR CERTIFIED SECURE ASSET SOLUTIONSSERVICE CENTER REPAIRSExperienced engineers and techni …
  • MSW

    MSW-FI-7500

    (13 pages)
    EXPONDO.DEFREQUENCY INVERTER MSW-FI-7500MSW-FI-5500MSW-FI-3700MSW-FI-2200MSW-FI-1500MSW-FI-15000MSW-FI-11000MSW-FI-750BEDIENUNGSANLEITUNGUser manual | Instrukcja obsługi | Návod k použití | Manuel d´utilisation | Istruzioni per l‘uso | Manual de instrucciones …

Comments, Questions and Opinions: