Smeg FSP9610X Instruction Manual

Text of Smeg FSP9610X User Guide:

• Smeg FSP9610X, Cleaning and maintenance 28 3. To reassemble the door, put the hinges in the relevant slots in the oven, making sure that grooved sections A are resting completely in the slots. Lower the door and once it is in place remove the pins from the holes in the hinges. 4.4 Cleaning the door glazing The glass in the door should always be kept thoroughly clean. Use absorbent kitchen roll. In case of stubborn dirt, wash with a damp sponge and an ordinary detergent. 4.5 Removing the internal glass panes For easier cleaning the door internal glass panes can be disassembled. 1. Remove the internal glass pane by pulling the rear part gently upwards, following the movement indicated b

• Installation 43 EN 3. Assemble the fastening bracket. 4. Align the base of the hook on the fastening bracket with the base of the slot on the wall fastening plate. 5. Align the base of the fastening bracket with the ground and tighten the screws to fix the measurements. 6. Use 50 mm for the distance from the side of the appliance to the bracket holes.

• Smeg FSP9610X, Installation 46 3. Clip the tongues of the upstand to the ventilation slot of the cooktop. (A) 4. Secure the upstand to the cooktop by tightening the 2 screws previously loosened. 5.5 Electrical connection General information Check the grid characteristics against the data indicated on the plate. The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance. Do not remove this plate for any reason. Perform the ground connection using a wire that is 20 mm longer than the other wires. Power voltage Danger of electrocution •

• Smeg FSP9610X, Use 22 Setting the time On the first use, or after a power failure, the digits will be flashing on the appliance’s display. 1. Press the keys and at the same time. The dot between the hours and the minutes flashes. 2. The time can be set using the key or . Keep the key pressed in to increase or decrease rapidly. 3. Press the key or wait 5 seconds. The dot between the hours and the minutes stops flashing. 4. The symbol on the display indicates that the appliance is ready to start cooki

• Smeg FSP9610X, Use 14 3 Use 3.1 Instructions High temperature inside the oven during use Danger of burns • Keep the oven door closed during cooking. • Protect your hands wearing heat resistant gloves when moving food inside the oven. • Do not touch the heating elements inside the oven. • Do not pour water directly onto very hot trays. • Do not allow children younger than 8 years old to come near the appliance when in operation. • If you need to move food or at the end of cooking, open the door 5 cm for a few seconds, let the steam come out, then open it fully. Improper use Danger of burns • Make sure that the flame-sp

• Smeg FSP9610X, Installation 39 EN 5.3 Adaptation to different types of gas In case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas cocks. Replacing nozzles 1. Remove the pan stands, burner caps and flame-spreader crowns to access the burner casings. 2. Replace the nozzles using a 7 mm socket wrench according to the gas to use (see “Burner and nozzle characteristics table”). 3. Replace the burners in the correct position. Adjusting the minimum setting for natural gas Light the burner and turn it to the minimum position. Extract the gas cock knob and turn the adjustment screw next to

• Smeg FSP9610X, Installation 41 EN General information This appliance may be installed next to walls, one of which must be higher than the worktop, at a minimum distance of 50 mm from the side of the appliance, as shown in figures A and C relative to the installation classes. Any wall units positioned above the worktop must be at a minimum distance of at least 600 mm. If a hood is installed above the cooktop, refer to the hood instruction manual to ensure the correct clearance is left. Depending on the type of installation, this appliance belongs to classes: A - Class 1 (Free-standing appliance)

• Use 15 EN Escaping gas may cause an explosion. If you smell gas or notice any faults in the gas installation: • Immediately shut off the gas supply or close the gas cylinder valve. • Immediately extinguish all naked flames and cigarettes. • Do not use any light or appliance switches and do not pull any plugs out of sockets. Do not use any telephones or

• Smeg FSP9610X, Use 25 EN Cooking information table Food Weight (Kg) Function Runner position from the bottom Temperature (°C) Time (minutes) Lasagne 3 - 4 Convection 1 220 - 230 45 - 50 Pasta bake 3 - 4 Convection 1 220 - 230 45 - 50 Roast veal 2 Fan assisted/Fan forced 2 180 - 190 90 - 100 Pork 2 Fan assisted/Fan forced 2 180 - 190 70 - 80 Sausages 1.5 Fan grill 4 MAX 15 Roast beef 1 Fan assisted/Fan forced 2 200 40 - 45 Roast rabbit 1.5 Fan forced 2 180 - 190 70 - 80 Turkey breast 3 Fan assisted/Fan forced 2 180 - 190 110 - 120 Roast pork neck 2 - 3 Fan assisted/Fan forced 2 180 - 190 170 - 180 Roast chicken 1.2 Fan assisted/Fan forc

• Installation 35 EN 5 Installation 5.1 Clearances above and around domestic appliances This appliance must be installed by an authorised person in accordance with this instruction manual, AS/NZS 5601.1 – Gas installations (installation and pipe sizing), local gas fitting regulations, local electrical regulations, Building Code of Australia and any other government authority. Requi

• Use 21 EN Advice for defrosting and proving • Place frozen foods without their packaging in a lidless container on the first shelf of the oven. • Avoid overlapping the food. • To defrost meat, use the rack placed on the second level and a tray on the first level. In this way, the liquid from the defrosting food drains away from the food. • The most delicate parts c

• Smeg FSP9610X, Use 17 EN 3.4 Using the cooktop All the appliance's control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anti- clockwise to the maximum flame symbol, until the burner lights. If the burner does not light in the first 15 seconds, turn the knob to and wait 60 seconds before trying again. After lighting, keep the knob pressed in for a few seconds to allow the thermocouple to

• Smeg FSP9610X, Description 12 5 Cooktop burner knobs Useful for lighting and adjusting the cooktop burners. Press and turn the knobs anti-clockwise to the value to light the relative burners. Turn the knobs to the zone between the maximum and minimum setting to adjust the flame. Return the knobs to the position to turn off the burners. 2.4 Other parts Shelves The appliance features shelves for positioning trays and racks at different heights. The insertion heights are indicated from the bottom upwards (see 2.1 General Description). Cooling fan The fan cools the oven and comes into operation during cooking. The fan causes a steady outflow of air from above the door which may contin

• Smeg FSP9610X, Cleaning and maintenance 30 Manually disengaging the door lock lever The door lock lever is located in the first slot on the left under the control panel, in the upper part of the front of the oven. During normal cleaning operations, the door lock lever may be activated accidentally. Door lock lever activated (as seen from above) 1. Move the door lock lever to the right until it stops. (as seen from above) 2. Release the door lock lever gently. The spring of the mechanism brings the door lock lever back into the disengaged pos

• Smeg FSP9610X, Contents 3 EN 1 Instructions 4 1.1 General safety instructions 4 1.2 Identification plate 8 1.3 Manufacturer liability 8 1.4 Appliance purpose 8 1.5 This user manual 8 1.6 How to read the user manual 9 2 Description 10 2.1 General Description 10 2.2 Cooktop 11 2.3 Control panel 11 2.4 Other parts 12 2.5 Available accessories 12 3 Use 14 3.1 Instructions 14 3.2 First use 15 3.3 Using the accessories 16 3.4 Using the cooktop 17 3.5 Using the storage compartment 18 3.6 Using the oven 18 3.7 Cooking advice 20 3.8 Programmer clock 21 4

• Smeg FSP9610X, Cleaning and maintenance 31 EN 4.6 Pyrolytic cycle Preliminary operations Before starting the pyrolytic cycle: • Clean the internal glass panel following the usual cleaning instructions. • For very stubborn encrustations spray an oven cleaning product onto the glass (read the warnings on the product); leave for 60 minutes, then rinse and dry the glass using kitchen roll or a microfibre cloth. • Completely remove all accessories from inside the oven. • Remove the rack/tray support frames. • Close the door. Pyrolytic function setting 1. Turn the function knob to the symbol: The pyrolytic cycle minimum duration (2 h

• Smeg FSP9610X, Installation 47 EN The appliance can work in the following modes: • 220-240 V 2~ 3 x 2.5 mm² three-pole cable. • 220-240 V 3~ 4 x 2.5 mm² four-pole cable. • 220-240 V 1N~ 3 x 2.5 mm² three-pole cable. • 380-415 V 2N~ 4 x 2.5 mm² four-pole cable. • 380-415 V 3N~ 5 x 1.5 mm² five-pole cable. 5.6 Access to the terminal board (depending on the model) Access via the plate To connect the power supply cable, access to the terminal board on the rear cover: 1. Remove the screws securing the lid to the rear cover. 2. Sligh

• Smeg FSP9610X, Installation 48 3. Install the power supply cable. 4. At the end, reposition the lid on the rear cover and secure it with the previously removed screws. Access via the rear casing To connect the power cable, remove the fastening screws on the rear casing as shown in the figure. Fixed connection Fit the power line with an omnipolar circuit breaker in compliance with installation regulations. The circuit breaker should be located near the appliance and in an easily reachable position. Connection with plug and socket Make sure that the plug and socket are of the same type. Avoid using adapters, gang sockets or extensions as these could cause overheating and a risk of burns. 5.7 For

• Smeg FSP9610X, Instructions 5 EN • When in use, do not place metal objects, such as dishes or cutlery, on the surface of the cooktop as they may overheat. • Do not insert pointed metal objects (cutlery or utensils) into the slots in the appliance. • Do not pour water directly onto very hot trays. • Keep the oven door closed during cooking. • If you need to move food or at the end of cooking, open the door 5 cm for a few seconds, let the steam come out, then open it fully. • Do not open the storage compartment (if present) when the oven is on and still hot. • The items inside the storage compartment could be very hot after the ove

• Instructions 8 • After carrying out any operation, check that the tightening torque of gas connections is between 10 Nm and 15 Nm. • At the end of the installation, check for any leaks with a soapy solution, never with a flame. • Have the electrical connection performed by authorised persons. • The appliance must be connected to earth in compliance with electri

• Smeg FSP9610X, Cleaning and maintenance 26 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance Recommendations for cleaning the cooktop To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Cleaning the cooktop 1. Pour some non-abrasive detergent on a damp cloth and wipe down the surfaces. 2. Rinse thoroughly. 3. Dry with a soft cloth or a microfibre cloth. Cleaning the cooktop grids, flame- spreader crowns and burner caps 1. Remove the components from the cooktop. 2. Clean them

• Smeg FSP9610X, Installation 44 7. Move the bracket onto the wall and mark the position of the holes to be drilled in the wall. 8. After drilling the holes in the wall, use wall plugs and screws to fasten the bracket to the wall. 9. Push the cooker towards the wall, and at the same time, insert the bracket in the plate fastened to the rear of the appliance. Wall fixing 1. Turn the screw placed behind the cooktop near the gas connection. 2. Attach the chain to the cooker with the screw just removed. 3. Stretch it out horizontally so that the other end of the chain touches the wall.

• Use 24 Minute minder timer The minute minder timer can be activated at any time. 1. Press the key . The display shows the digits and the indicator light flashing between the hours and the minutes. 2. Use the key or to set the required minutes. 3. Wait approx. 5 seconds without pressing any key to finish setting the minute minder. The current time and the symbols and

• Smeg FSP9610X, Use 20 3.7 Cooking advice General advice • Use a fan assisted function to achieve consistent cooking at several levels. • It is not possible to shorten cooking times by increasing the temperature (the food could be overcooked on the outside and undercooked on the inside). Advice for cooking meat • Cooking times vary according to the thickness and quality of the food and to consumer taste. • Use a meat thermometer when roasting meat, or simply press on the roast with a spoon. If it is hard, it is ready; if not, it needs another few minutes cooking. Advice for cooking with the G

• Smeg FSP9610X, Use 23 EN 6. Press the keys and at the same time to reset the programmer clock. Programmed cooking 1. Set the cooking time as described in the previous point “Timed cooking”. 2. Press the key . The sum of the current time plus the pre-set cooking duration will appear on the display. 3. Use the key or to set the required minutes. 4. Wait approx. 5 seconds without pressing any key in order for the function to activate. The current time and the symbols and will appear on the display. 5. At the end of cooking the heating elements will be deactiv

• Smeg FSP9610X, Cleaning and maintenance 34 What to do if... The appliance does not work. • The circuit breaker is faulty: look in the fuse box and check that the circuit breaker is in working order. • Power cut: check whether the kitchen light works. The gas burner does not ignite. • Power cut or damp ignition plugs: light the gas burner with a gas lighter or a match. The oven does not heat up. • Faulty fuse: check and, if required, replace the circuit breaker. • The function knob has not been set: set the function knob. All dishes that are prepared in the oven burn within an extremely short period of time. • Faulty thermostat: call the Authorised Assistance Centres

• Smeg FSP9610X, Description 13 EN Rack Useful for supporting containers with food during cooking. Tray rack To be placed over the top of the oven tray; for cooking foods which may drip. Tray Useful for collecting fat from foods placed on the rack above. Deep tray Useful for collecting fat from foods placed on the rack above. The accessories intended to come into contact with food are made of materials that comply with the provisions of current legislation. Supplied and optional accessories can be requested to Authorised Assistance Centres. Use only original accessories supplied by the

• Smeg FSP9610X, Instructions 9 EN 1.3 Manufacturer liability • The manufacturer declines all liability for damage to persons or property caused by: • use of the appliance other than the one envisaged; • non-observance of the user manual provisions; • tampering with any part of the appliance; • use of non-original spare parts. 1.4 Appliance purpose • This appliance is intended for cooking food in the home environment. Every other use is considered improper. • The appliance is not designed to operate with external timers or with remote-control systems. 1.5 This user manua

Related Products and Documents (Kitchen Appliances):

Comparable Devices:

Similar Resources:

• Superior 10002120 (9 pages) Sandwich MakerArticle number10002120 (white) + 10002138 (black)Power supply 220-240V ~ 50 HzElectrical protection class IOutput power 700 WattNet weight 1.17 kgIndicator lightAutomatic temperature controlNon-stick coated platesFixed plates with triangular design Locking clipV02aINSTRUCTIONS FOR USEENGLISH10002120-2138_SW-43_IM_V02_A_P130021_2013_02_21_GB.ind …

• Air innovations WG15 (41 pages) 1 Wine Cellar Cooling Systems Through-the-Wall Wine Cellar Cooling Systems Installation, Operation and Maintenance Guide Models: WG15 and WG25 50Hz Manufactured by: Syracuse, NY www.wineguardian.com www.airinnovations.com Wine Guardian reserves the right, without noti …

• Takex PIR-T40NAM (12 pages) ①PIR-T40NAM (W) is passive infrared sensor that detects far-infrared rays emitted from the human body and outputs a contact signal. Since this unit significantly reduces lost and false detection using the unique triple mirror and signal processing systems, it can be used both for indoor and outdoor applications. This unit has the following features suitabl …

• Rotronic HygroClip2 ADVANCED (2 pages) 12.1085.0105D12.1085.0105ERotronic.com Rotronic.comProces sSensing.com Proces sSensing.comHYGROCLIP2 ADVANCEDShort Instruction ManualHYGROCLIP2 ADVANCEDKurzbedienungsanleitung1 GENERAL DESCRIPTIONYour Rotronic HygroClip2 Advanced is a lead-ing-edge product that meets all established standards. It will work perfectly for years if you follow the assembly and …

• Gold Medal 2018 (11 pages) Part No. 79434 Instruction Manual 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA Excalibur Hot Wand Model No. 2018, 2018EX …

• Impact Subsea ISM3D (28 pages) www.impactsubsea.com Innovative Underwater Products ISM3D Heading, Pitch & Roll Sensor Installation & Operation Manual Revision: 1.2Date: 09/01/19Impact Subsea LtdT. +44 (0) 1224 460 850E. [email protected]. www.impactsubsea.com …

Comments, Questions and Opinions: