Epson PP-1002 Operation & User’s Manual
|
Epson PP-1002, 101 Maintenance Maintenance information of your product appears. PP-100II PP-100 PP-100AP PP-50 Item Description Total discs published Cumulative number of discs the product has published (writing/printing). Number of printed discs Cumulative number of discs the product has printed. Maintenance Box free space Free space of the maintenance box (0 to 100%) If Maintenance Box free space is close to 0%, it is time to replace it. Service life of Drive 1/2 Usage status of the drive 1 and drive 2. (0 to 100%) If Service life of Drive is close to 100%, it is time to replace it. Item Description Number of printed discs Cumulative number of discs the product has
23 Basic Operations Handling Stackers Handle the stackers as shown below. Stacker 1/Stacker 2 Stacker 1 and Stacker 2 are the same. Handle them in the same way. Attach Line up the indentations and attach. Remove Gently lift and pull towards you to take out. Stacker 1 Stacker 2
Epson PP-1002, 47 Using Software Input Stacker Allows you to select the stacker where the discs to be written/printed are set. Output Stacker Allows you to select the stacker to which to output published discs. Label Type Allows you to select the type of disc label to be printed. Color Select Color to print in color, and select Black for monochrome printing. Quality/ Speed PP-100II PP-100 PP-50 1: Prints labels with an emphasis on printing quality. 2: Prints labels with an emphasis on printing speed. PP-100AP 1: Prints labels with an emphasis on printing quality. 2: Prints labels with an emphasis on printing speed. 3: Prints labels with even more emphasis on speed than wh
Epson PP-1002, 26 Software Settings This section describes the basic settings of the software required for using the product (PP-100II/PP-100/PP-100AP/ PP-50) after the setup. (For the setup procedure, see Setup Guide for Mac.) Installing Software The installation procedure installs the following software on your PC. (For the installation procedure, see Setup Guide for Mac.) • EPSON Total Disc Utility This software is used to set up the product and check the product status from your PC. • EPSON Total Disc Maker This software is used to edit the write data* and the print data for the label surface and to publish using this product. • Printer driver * Editing write
32 Write Settings (Only for PP-100II/PP-100/PP-50) Follow the steps below to set Write Speed and Write Verification with the PP-100II/PP-100/PP-50. 1 Start up EPSON Total Disc Utility. See “Starting EPSON Total Disc Utility” on page 39. 2 Select Common Settings for Publishing from the To ol s menu. 3 Click Write Settings. The Write Settings screen appears. 4 Set Write Sp
Epson PP-1002, 87 Maintenance Cleaning the Print Head Head cleaning is a function for cleaning the surface of the print head to maintain the print quality. Run head cleaning if the printing becomes faint or gaps appear in the printing. Print head cleaning consumes ink. Before running print head cleaning, you can run a nozzle check to check whether or not the nozzles are clogged. This makes it possible to prevent consuming extra ink during print head cleaning. (See “Checking the Print Head Nozzles” on page 85.) Causes and Solutions for Print Head Drying Cause Prevention This product has a print head cap to prevent it from drying, the same way th
Epson PP-1002, 140 6 Grasp the fixture as shown in the figure below, and push the printer tray in the direction of the arrow indicated below. 7 Open the disc cover. 8 Pull out the printer tray. 9 Use a soft cloth to wipe off any dirt on the printer tray. 10 Close the disc cover. The printer tray automatically closes when the power is turned on in Step 14. 11 Reinstall the maintenance box.
Epson PP-1002, 10 WARNING The connection of a non-shielded interface cable to this product will invalidate the EMC standards of this device. You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your authority to operate the equipment. For PP-100/PP-100AP in Europe, PP-100II and PP-50 This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC Compliance Stat
Epson PP-1002, 93 Maintenance Correcting the Printing Position Adjust the printing position if it has shifted towards the top, bottom, left, or right. 1 Set one unprinted disc into Stacker 1. 2 Display the Printer Utility screen of the EPSON Total Disc Utility. See “Properties screen (General screen)” on page 41 for display procedure. 3 Click Printing Position Correction.
Epson PP-1002, 11 Before Using this Product For PP-100II/PP-50 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to c
Epson PP-1002, 48 Color Options area In Color Options area, you can adjust print colors. Display the printer driver screen, and select Color Options to display the Color Options area. • If you wish, you can make color adjustments at the time of printing without making color adjustments to the actual data. • If Color is set to Black in the Print Settings area, color adjustments cannot be made. • For adjusting print colors, see “Adjusting Print Colors” on page 79. Notes
Epson PP-1002, 20 Turning Power On/Off This section describes how to turn the power on and off. Turning On the Power 1 Connect the power cord. 2 Press the power button. The Power light flashes green, then stays on. Turning Off the Power Press the power button until the Power light flashes. The Power light flashes in green then goes off; then the power is turned off. • The fan may continue to operate after the power is turned off, but it will automatically stop after 15 minutes. • The product may not be recognized by the PC when the power is turne
Epson PP-1002, 41 Using Software Properties screen (General screen) On the Main screen, double-click a model name for Device Name or click [Properties] to display the device’s Properties screen. Click the General tab, Maintenance Info tab, and About tab to display each screen. Click Printer Utility in each screen to display the Printer Utility screen. You can also display the Properties screen by clicking in Publish view of EPSON Total Disc Maker. Notes
129 Troubleshooting 6 Pull out the printer tray. 7 Remove the disc, and close the disc cover. The printer tray automatically closes when the power is turned on in Step 9. 8 Reattach the maintenance box cover. 9 Insert the power plug into the outlet, and turn on the power.
Epson PP-1002, 115 Troubleshooting Error Associated with Disc Transfer Lights Conditions/Remedies Power BUSY ERROR INK STACKER 1 2 3 4 Disc pick error Resolve the problem as follows. 1. Open the disc cover and fully separate the discs in the input stacker to prevent them from sticking together. 2. Close the disc cover and retry to publish a disc. Multiple feed error Resolve the problem as follows. 1. Open the disc cover. 2. Remove all the discs from both the drive tray and the printer tray. 3. Fully separate the discs in the input stacker to prevent them from sticking together. 4. Close the disc cover and retry to publi
Epson PP-1002, 24 Stacker 3 Attach (Only for PP-100II/PP-100/PP-100AP) Hold the handle, line up the indentations, and attach. Remove (Only for PP-100II/PP-100/PP-100AP) Hold the handle, lift it up, and then pull towards you to take out. For PP-50 Stacker 3 is fixed. Its shape differs from that of stacker 3 for the PP-100II, PP-100 and PP-100AP. • When you insert Stacker 3, first check that there are no discs in Stacker 4, and then attach it. • When you use Stacker 3, set the lock lever to LOCK, and do not pull out Stacker 4.
Epson PP-1002, 80 The adjusting procedure differs, depending on whether you publish with EPSON Total Disc Maker or with other applications. When publishing with EPSON Total Disc Maker Set in the dialogue that is displayed when you click Color Settings... in Publish view of EPSON Total Disc Maker. Click Color Correction to configure each setting. When publishing with other applications Select Color Correction in the Color Options area of the printer driver to set Mode and Gamma. Click Adjustments to set the rest of the items. • If you set Print Mode Setting to Black in Publish view of EPSON Total Disc Maker, you can adjust only Gamma, Brightness, and Contrast. • Select ColorSync w
Epson PP-1002, 90 Aligning the Print Head If the print position when the print head moves from right to left is not aligned with the print position when the print head moves from left to right, gaps may appear in vertical lines, and the print results may become blurry. If this happens, run print head alignment. 1 Set one unprinted disc into Stacker 1. 2 Display the Printer Utility screen of the EPSON Total Disc Utility. See “Properties screen (General screen)” on page 41 for display procedure. 3 Click Print Head Alignment.
25 Basic Operations Stacker 4 (Only for PP-100II/PP-100/PP-100AP) Pull out Hold the Stacker 4 grip and pull out the stacker. Push in Hold the Stacker 4 grip and push the stacker in. • Do not apply strong force to Stacker 4 when handling it. • When the BUSY light and the STACKER 4 light are flashing rapidly, a disc is being ejected, so do not pull out Stacker 4. Discs may be dama
Epson PP-1002, 81 Maintenance Maintenance Replacing the Ink Cartridge Checking the Ink Levels When it becomes time to replace even one of the six ink cartridges, printing is no longer possible. The INK light on the control panel notifies you the ink levels as follows. • When the INK light flashes, the remaining ink of that color is low. Prepare a new ink cartridge. • When the INK light turns on, it is time to replace the ink cartridge of that color. Replace it with a new ink cartridge. You can check the ink level
Epson PP-1002, 135 Troubleshooting Disc Recording Surface is Stained with Ink When the disc recording surface is stained with ink, the printer tray may be dirty. Clean the printer tray by following the procedure below. For PP-100II 1 Turn the product off. See “Turning Off the Power” on page 20. 2 After the Power light goes off, unplug the power plug from the outlet. 3 Remove the two screws to remove the maintenance box cover. 4 Grasp the fixture as shown in the figure below, and push the printer tray in the direction of the arrow indicated below. 5 Open the disc
Epson PP-1002, 33 Software Settings Uninstalling the Software If the software could not be installed properly, uninstall (delete) the software, and then reinstall it. 1 Turn off the product. See “Turning Off the Power” on page 20. 2 Exit all applications that are running. 3 Click [System Preferences] in the Dock. 4 Click [Print & Scan] ([Print & Fax] in Mac OS X v10.6) in Hardware. 5 Select the printer to be deleted, and click [-]. 6 When the confirmation message appears, click Delete Printer. 7 Click [Applications]. 8 Click EPSON Software. 9 Click [Uninstaller]. You may be asked for an administrator password when uninstalling the
Epson PP-1002, 111 Troubleshooting Label Printing Problems Symptom/Problem Status Check/Remedy Procedure • Rubbing • Lines or streaks are formed • Blurriness • Text or lines are shaky • Incorrect color tones • Some colors are not printed • Unevenness in the printing • Mosaic-like patterns are printed • Printing is grainy (jagged) Are the print head nozzles clogged? Perform a nozzle check to confirm the status of the print head, and if it is clogged, perform head cleaning. See the information below for details. • “Checking the Print Head Nozzles” on page 85 • “Cl
Epson PP-1002, 92 6 Select the number of the pattern with the fewest vertical lines. In the illustration above, the pattern with the fewest vertical lines is “5”, so select “5.” If you want to print the print head alignment pattern again, to check it, set a disc in Stacker 1, and click Realign. 7 Click Finish.
Epson 980N - Stylus Color Inkjet Printer Disc Duplicator Start here manual
980N - Stylus Color Inkjet Printer |
Epson 4000 - Stylus Pro Color Inkjet Printer Disc Duplicator Product support bulletin
4000 - Stylus Pro Color Inkjet Printer |
Epson LQ-680 Pro Disc Duplicator Specifications
LQ-680 Pro |
Epson Stylus C 60 Disc Duplicator Service manual
Stylus C 60 |
Epson RX500 - Stylus Photo Color Inkjet Disc Duplicator Start here manual
RX500 - Stylus Photo Color Inkjet |
Epson EMP 600 Disc Duplicator Specifications
EMP 600 |
Epson Stylus Pro 4480 Disc Duplicator Specification sheet
Stylus Pro 4480 |
Epson StylusRIP Professional (Stylus Photo 2200 Disc Duplicator Start here manual
StylusRIP Professional (Stylus Photo 2200 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Deni | 15600 | Instructions for proper use and care manual | deni/15600-2PT.pdf | 21 Sep 2023 | 6 | 0.1 Mb |
2 | Lincoln Electric | 2002 Town Car | Owner's manual | lincoln-electric/2002-town-car-8C3.pdf | 28 Sep 2022 | 249 | |
3 | Linksys | WMP11 - Wireless-B PCI Card | Specifications | linksys/wmp11-wireless-b-pci-card-ED2.pdf | 07 Jul 2022 | 2 | |
4 | Nokia | Lumia 1320 | Quick start manual | nokia/lumia-1320-42H.pdf | 30 Aug 2023 | 2 | |
5 | Central Machinery | 33684 | Assembly and operating instructions manual | harbor-freight-tools/33684-L98.pdf | 31 Oct 2023 | 18 | 3.57 Mb |
6 | Shark | Press & Refresh GS5000 Series | Operation & user’s manual | shark/press-refresh-gs5000-series-L5J.pdf | 24 Nov 2022 | 17 |
Addonics Technologies
Technical SupportIf you need any assistance to get your unit functioning properly, please have your product information ready and contact Addonics Technical Support at:Hours: 8:30 am - 6:00 pm PSTPhone: 408-453-6212Email: http://www.addonics.com/support/query/T E C H N O L O G I E Swww.addonics.com1:11 HDD Duplicator(HDUS11SNDX)User Guide
…
HDUS11SNDX(16 pages) |
MicroBoards Technology
Quick Reference Guidefor Windows Vista, XP, and 2000Rev 08.9.24Please visit our Technical Support website at www.microboards.netFor a more in-depth look at the installation process, please referto the Installation section of the User’s Manual.Be sure your computer meets the Minimum SystemRequirements as stated in the User’s Manual and thatyou have read …
GX-2(2 pages) |
Edge10
duplicate digital media...take a closer look at our web2.0site www.edge10.comThe EdgeDupe is a standalone device which enables users to have multiplecopies of their CD, Blu-Ray DVD, USB stick or SD Card in a matter of minuteswith no PC required. The EdgeDupe is a professional grade duplicating unit,which combined with high quality Pioneer drives, makes it th …
SD707(3 pages) |
Riso
Please contact the following for supplies and service:2021/11About This MachineBasic OperationsFunctions for Master MakingFunctions for PrintingUseful FunctionsFunctions for ScanningSetting the Operation ConditionsRISO ConsoleReplacing ConsumablesMaintenanceTroubleshootingAppendix069-36005123456789101112The “RISO MH9450/9350 Basic Guide”, which supports …
MH Series(218 pages) |
Primera
CD/DVD/BD Disc PublisherBränn och Skriv ut på CD-, DVD- och Blu-ray skivor – Automatiskt!• Programvara för bränning ochutskrift för Windows®Vista/XP/2000 och Mac®Enkel produktion av CD-, DVD- och Blu-Ray skivorHar du någonsin varit tvungen att brännaskivor en i taget och sedan manuellt skrivaut och klistra på etiketter? I så fall vet du hurmyc …
Disc Publisher SE(2 pages) |
Addonics Technologies
Technical SupportIf you need any assistance to get your unit functioning properly, please have your product information ready and contact Addonics Technical Support at:Hours: 8:30 am - 6:00 pm PSTPhone: 408-453-6212Email: http://www.addonics.com/support/query/v8.1.11T E C H N O L O G I E Swww.addonics.comUser Guide1:11 HDD Duplicator NB(HDUS11NB)
…
HDUS11NB(18 pages) |
Sangean Portable Radio PR-D9W -#393JWX: PR-D9W - Portable Radio Operating instruction PR-D9W -, 25 |
Cuisinart Kitchen Appliances CEK-50CEK-50 (Kitchen Appliances ePDF Guide, #EIJYD9) CEK-50, 12 |
Casio Digital Camera EXH20GPDF User Guide (@24MI73), Casio EXH20G Digital Camera (Sat 01.2024) EXH20G, 192 |
Astar LCD TV LTV-40HBGAstar LTV-40HBG LCD TV Operation & user’s manual LTV-40HBG, 53 |
Kenwood Car Video System Spectrum 855 AV#UY6V88: Spectrum 855 AV Car Video System Using manual Spectrum 855 AV, 56 |
LG Speaker System SoundPlate LAP340LG Speaker System SoundPlate LAP340 Owner's manual SoundPlate LAP340, 20 |
Cognex Barcode Reader DM503Cognex Barcode Reader Quick reference manual (File: cognex-dm503-quick-reference-manual-16, 05th Oct 2023) DM503, 16 |
Castex Scrubber TS-2700Scrubber Operator and parts manual (Castex TS-2700) TS-2700, 45 |
Philips Electric Shaver HQ6990Philips Electric Shaver Operation & user’s manual (File: philips-hq6990-operation-user-s-manual-9, Wed 11.2023) HQ6990, 9 |
AEG Coffee Maker PE8038-MCoffee Maker PDF Operation & user’s manual PE8038-M, 41 |
Mazda Automobile DemioUser Manual: Mazda Demio (9X3EAA, Upd.Wednesday 29-11-2023) Demio, 358 |
Audiovox GPS NPD5500 - Navigation System - in-dashAudiovox NPD5500 - Navigation System - in-dash GPS Owner's manual NPD5500 - Navigation System - in-dash, 36 |