Etec 48E700LC Operation & User’s Manual

Text of Etec 48E700LC User Guide:

• Etec 48E700LC, 48E700LC-17 Installation Connection to a Personal Computer Connecting a PC or laptop Connecting to an amplifer or home theater system Recommended computer display resolution:1920x1080@60 Hz How to Connect a PC • Connect using a male to male VGA cable (not included) from your PC to the “VGA” on the TV’s panel. How to Connect Audio Sound • Connect a 3.5mm audio cable (not included) from the computer’s mini audio output jack to the audio input on the TV’s panel. How to Use • Press the INPUT button on the remote control. Use the buttons  to highlight PC. Press ENTER. NOTE: If your PC uses a standard signal mode, the screen will adjust

• Etec 48E700LC, 48E700LC-31 TV Settings TV Provider Changes & Channel Auto Scan After Initial Setup To enter the Channel Menu: • Press the MENU button • Using the t u arrow buttons; scroll to highlight Channel • Press the down q arrow buttons to highlight Air / Cable Select Cable if you subscribe to a pay television service without a set top box. • Press the t u arrow buttons to highlight Cable. • NOTE: Channel Auto Scan may take several minutes to complete. Cable Mode Air Mode Select Air when TV is connected to an indoor

• Etec 48E700LC, 48E700LC-5 Table of Contents Important Safety Instructions .........................................................................................................................................1 Table of Contents ..........................................................................................................................................................5 Introduction ....................................................................................................................................................................6 Installing the Base .............................

• 48E700LC-14 Installation Connection to Component YPbPr Input How to Connect • Match and insert the green (Y), blue (Pb), and red (Pr) cables into the device and TV. Next, connect the red and white (L & R) audio cables. *NOTE: The picture will be black & white if hooked up incorrectly. You must hook up audio cables separately. How to Use �

• Etec 48E700LC, 48E700LC-12 NOTE: You must remove the pedestal before wall mounting. TV Overview Rear Panel          8. USB Input 9. CABLE-ANTENNA Port supports MP3 and JPEG. 6. HDMI video and up to 7.1-channel digital audio all from one cable. Recommended for best performance. HDMI cable not included. 7. PC Audio Input (3.5mm) - 3.5mm audio cable (not included) for sound. VGA Input - Connect an optional VGA cable (not included) from your personal computer. - Connect an antenna or cable

• 48E700LC-4 Safety Instructions 15. Replacement Parts 16. Safety Check Upon completion of any service or repairs to this TV, ask the service technician to perform safety checks to determine whether the product is in proper operating condition. 17. Wall Mounting The TV should be mounted to a wall only by a professional. The TV may slide or fall, causing serious injury to a child or

• Etec 48E700LC, 48E700LC-32 Aspect Modes 1. NORMAL Recommended for viewing native widescreen content and undistorted 4:3 images (with black bars). 2. WIDE Stretches certain 4:3 content and may reduce visible black bars. 3. ZOOM viewing widescreen content. The Zoom effect will crop images somewhat. 4. CINEMA n eliminating visible side black bars. It may also eliminate or reduce black bars on certain widescreen movies. Press ASPECT to cycle through the following widescreen settings. The ASPECT function offers several viewing display options on the 16:9 screen. Press the ASPECT button to cycle through the following widescreen settings. NOTE: The ASPECT function is not available f

• Etec 48E700LC, 48E700LC-25 Menu Adjustments Note: When adjustments are completed, you may select another menu by pressing the Menu button. Closed Captions The Setup menu includes adjustments for activating the Closed Caption text feature for display on-screen and customiz- ing CC display types and font styles. How to Navigate: Press the MENU button on the remote control. Navigate using arrow t u buttons to select Setup. • Press the down q arrow button to highlight Closed Caption then press the u arrow button to highlight CC Mode. • Navigate using the t u arrow buttons to select CC Off - CC On - CC on Mute. • Press down

• Etec 48E700LC, 48E700LC-16 Installation Connection to Antenna & Cable / Satellite Box We recommend using a high quality roof top antenna, digital cable, or satellite box for the best display and performance. Note: Reception quality is determined by your location, geographical terrain, distance from the local broadcast transmitter, and strength of antenna. Connecting an antenna or basic cable service: • Connect the RF coaxial (75 ohm) cable from existing roof top / in door antenna, or wall outlet. • Finger tighten the Coaxial / RF Cable end to the TV input on the panel. Coaxial / RF Cable (not included) Ant./Cable Wall Outlet Roof Antenna / Cable Outlet Installation Connecting to POWER IN �

• Etec 48E700LC, 48E700LC-23 Menu Adjustments Date & Time Settings Note: When adjustments are completed, you may select another menu by pressing the Menu button. The Time menu includes adjustment of settings for your local time zone and daylight savings time. The clock will adjust automatically after the initial Channel Auto Scan of available broadcast channels in your area. How to Navigate: Press the MENU button on the remote control. Navigate using arrow t u buttons to select Time. • Press down q arrow button to highlight Sleep Timer then press the u arrow button to select time to view before the television timer turns the set off: 5 Min - 10 Min - 15 Min - 30

• 48E700LC-3 Safety Instructions 9. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the TV be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges. Article 810 of the National Electri- cal Code (U.S. A.), ANSI / NFPA 70 provides information with regard to proper grounding of the mast

• Etec 48E700LC, 48E700LC-13 Installation Connection to HDMI Input Blu-ray, HD DVD, or Game Console How to Connect • On the back of your device, connect the HDMI cable form HDMI out on device to HDMI in on the panel. How to Use • Press the INPUT button on the remote, then use the qp arrows to highlight HDMI. Press ENTER . Coaxial / RF Cable (not included) Optional HDMI cable ( not included ) Cable / Satellite set top box Optional HDMI cable ( not included ) Digital set top box, gaming console, or blu-ray w / HDMI interface Digital Cable / Satellite Set Top Box How to connect • On the back of your device, connect the HDMI cable from HDMI out on device to HDMI in on the panel. How to Us

• Etec 48E700LC, 48E700LC-27 Menu Adjustments CEC Settings The CEC menu includes options for controlling functions of compatible external devices connected via the HDMI input. Please refer to the instruction manual of your connected device to confirm if CEC control is possible. How to Navigate: Press the MENU button on the remote control. Navigate using arrow t u buttons to select Setup • Press the down q arrow button to highlight CEC then press the u arrow button to highlight CEC Control. • Navigate using the t u arrow buttons to select On - O ff. When you select On, the CEC functions open. Otherwise the CEC functions close. • Press the down q arrow button to highlight Device A

• Etec 48E700LC, 48E700LC-11 TV Overview IR Receiver 2. INPUT - After connecting your DVD, cable box, etc. select the appropriate input source to view. Press the INPUT button to display the input options. Press the CH+ / CH- buttons to highlight the input source and press the VOL+ button to select. 3. MENU - Press the MENU button to display. Press VOL+ to select from the 6 menu options available. Press the CH+ / CH- buttons to select a feature from the selected menu then press the VOL+/VOL- buttons to adjust the volume settin

• Etec 48E700LC, 48E700LC-19 TV Setup Initial Setup Wizard Initial Setup Wizard IMPORTANT NOTE: If your TV is connected to a Cable or Satellite set top box DO NOT run the “Channel Auto Scan” NOTE: the Setup Wizard only appears when turning on the TV for the first time. How to Navigate the Setup Menus: Use the pq arrow buttons on the remote to move to the menu selection. in STEP 3. After connecting your TV antenna or cable wire, turn the television ON. The quick Setup Wizard will display on-screen to help guide you through the 3 steps listed below: STEP 1: Choosing a Menu Language Use the tu arrow buttons on the remote to

• 48E700LC-1 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radi

• Etec 48E700LC, 48E700LC-15 Installation Connection to Composite Input Connecting a device with a Composite connection. How to Connect • Match and insert the yellow, red, and white A / V cables into the device and TV. How to Use • Press the INPUT button on the remote. Then use the qp arrow buttons to highlight AV. Press ENTER. Audio Video Cable (included) Digital set top box, gaming console or DVD Source Select PC Media HDMI1 HDMI2 HDMI3 YPbPr / AV

• Etec 48E700LC, 48E700LC-26 PC Menu Adjustments In the Setup menu you may adjust the position of images displayed on screen once you connect an input signal from your PC. The recommended resolution is 1920x1080. For use with a laptop computer, refer to your computer’s user manual on instruction for proper display output. If your PC system uses a standard signal mode, the TV screen will adjust automatically. Connect an optional 3.5mm audio cable for stereo sound. Advanced Settings How to Navigate: After conne

• Etec 48E700LC, 48E700LC-22 Menu Adjustments Audio Settings The Audio menu offers options to make sound enhancements while listening through the built-in speakers or to select digital audio options when connected to a Dolby Digital receiver though a (SPDIF) coaxial digital output. How to Navigate: Press the MENU button on the remote control. Navigate using t u arrow buttons to select Sound. Press the q arrow button to highlight Sound Mode, then press the u arrow button to select your sound preference from 5 factory options: Music - Movie - Sports - User - Standard Press down q arrow button to highlig

• 48E700LC-34 MHL Setting Connecting an MHL-enabled device You can connect a MHL-enabled device, such as certain models of smartphones & tablets, and view the device’s screen on the TV. Connecting a MHL-enabled device to the HDMI2 (MHL) input requires a special MHL cable. (Not included) To connect an MHL-enabled device: 3. 4. Connect a MHL cable to the micro USB

• Etec 48E700LC, 48E700LC-30 Menu Adjustments Channel Settings The Channel menu provides the setup / changes of your television to receive broadcast channels, store your favorite channels, add or skip channels in memory and label or name channels. How to Navigate: Press the MENU button on the remote control. Navigate using arrow t u buttons to select Channel. Press the down q button to highlight your preferences. • Highlight Favorite to add channels to your Favorites List. Navigate using the ◄►▼▲ arrow buttons to select channels to be added or deleted from your list

• Etec 48E700LC, 48E700LC-28 NOTE: PRT Setting and Reset RRT are not user adjustable settings. Menu Adjustments USA Parental Control In the Lock menu, you may block television and movie programming based on TV ratings and Motion Picture Association guidelines. To gain access and select your preferences within the Parental menu make certain your input is set to TV. How to Navigate: Press the MENU button on the remote control. Navigate using arrow t u buttons to select Lock. Gain access to parental rating options by pressing the down q arrow button to highlight Enter Password. Enter your 4 digit code (factory default code is “0000�

More Instructions:

Etec 48E700LC Quick start manual 16-07-2022 2

DOWNLOAD

Related Products and Documents (TV):

Comparable Devices:

Similar Resources:

• RCA G36705 (64 pages) colortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevisioncolortelevision …

• Telefunken D32H125A3C (13 pages) English - 17 -ContentsSafety Information ........................................ 18Getting Started ............................................. 19Notications & Features & Accessories ................ 19Features ............................................................... 19Inserting the Batteries into the Remote ................ 20Connect P …

• LG 32LN541C (38 pages) www.lgsolutions.comP/NO : MFL67694912 (1303-REV00)32LN541C 39LN541C 42LN541C47LN541C 55LN541C32LN549E 39LN549E 42LN549E47LN549E 55LN549E32LP560M42LP560MPlease read this manual carefully before operating your set and retain it for future reference.QUICK REFERENCE GUIDELED TV* LG LED TV applies LCD screen with LED backlights. …

• Sharp 21K-FD3RU (22 pages) OPERATION MANUALCOLOUR TELEVISION21K-FD3RU21K-FD5RUPlease read this operation manualcarefully before using the colour television.E1 [ SAFETYPRECAUTIONS ]E2 [ BEFOREOPERATINGTELEVISION ]• Connecting to an antenna• Connecting to an antennavia a VCRE3 [ CONNECTING ANDWATCHING DVD ]• Connecting to a DVDplayer• Watching DVDE4 [ ACCESSORIES ]E5 [ PART NAM …

• Sanyo DS27910 (30 pages) ASFILE NO.SERVICE MANUAL Remote Control ColorTelevisionDS27910 (U.S.A.)ORIGINAL VERSIONChassis No. 27910-00NOTE: Match the Chassis No. on the unit’s back cover with the Chassis No. in theService Manual.If the Original VersionService Manual ChassisNo. does not match theunit’s, additional ServiceLiterature is required. Youmust refer to “Notices” to …

• SunBriteTV 3220HD (1 pages) LCD Screen 31.5-inch diagonal TFT Active MatrixResolution 1366 x 768 Aspect Ratio 16:9Contrast Ratio 3000:1H/V Viewing Angle 178o by 178o Response Time 6.5 millisecondsTV formats 1080i, 720p, 480i, 480pInput Connectors: RF HDMI Video Composite Video Component PCAntenna/CATV (NTSC/ATSC/QAM)HDMI Input x2S-Video x1 and Composite Video x1, L …

Comments, Questions and Opinions: