Faraday LW401 Operation, Installation, And Maintenance Manual
|
Faraday LW401, 29 LW-401 Operation, Installation, and Maintenance ManualLW-401 TABLE 7 PROGRAMMING SHEET Level Sublevel Description 1 1 Initiating Device Circuit Zone 1 Enabled Bypassed 2 Initiating Device Circuit Zone 2 Enabled Bypassed 3 Initiating Device Circuit Zone 3 Enabled Bypassed 4 Initiating Device Circuit Zone 4 Enabled Bypassed 5 Initiating Device Circuit Zone 5 Enabled Bypassed 6 Initiating Device Circuit Zone 6 Enabled Bypassed 7 Initiating Device Circuit Zone 7 Enabled Bypassed 8 Initiating Device Circuit Zone 8 Enabled Bypassed 2 1 Optional LWZE-4A/LWZE-8A/
Faraday LW401, 10 Operation, Installation, and Maintenance Manual LW-401 To Acknowledge Alarms 1. Unlock and open the door. 2. Press ACK to acknowledge (Block Acknowledge) all alarms and other conditions. The system ALARM and the Zone ALARM LEDs on the front panel stop flashing and remain on. The system’s internal audible silences. To Silence The Notification Appliance Circuits Press SILENCE after all alarms are acknowl- edged. The BYPASS LED on the front panel flashes. The following four conditions are checked before the Notification Appliance Circuit(s) can be silenced: 1. If either NAC is programmed as NON- SILENCEABLE, it will not silence. 2. If the NAC in
Faraday LW401, i Table of Contents 1 INTRODUCTION .......................................................................................................................1 Standard Components ........................................................................................................2 MAIN BOARD ................................................................................................................................ 2 DISPLAY ....................................................................................................................................... 2 FRONT PANEL
Faraday LW401, 11 LW-401 Operation, Installation, and Maintenance ManualLW-401 Zone operation are described below. • Shorting-type input devices and smoke detectors are compatible with all zone types. • Manual fire alarm stations and smoke detectors can be mixed on zones where local codes allow. • On verified zones, the manual station reports alarms when activated, without delay. Alarm Verification The Alarm Verification Feature provides the LW-401 with a way to verify an alarm from area-type smoke detectors. This feature can be used to reduce incidences of false alarms. A detector supervised wit
19 LW-401 Operation, Installation, and Maintenance ManualLW-401 Level 6-4 - Set Simplified Zone Code Rounds 1. The selected number of rounds is shown by the red zone LEDs as indicated in the following table: Zone 3 LED = 3 rounds Zone 4 LED = 4 rounds Zone 5 LED = 5 rounds Zone 6 LED = 6 rounds Zone 7 LED = 7 rounds Zone 8 LED = 8 rounds 2. Press the Reset key to advance the pointer (yellow zo
Faraday LW401, 6 Operation, Installation, and Maintenance Manual LW-401 Installing the Control Panel Remove all system power before installation, first battery and then AC. (To power up, connect the AC first, then the battery.) All wiring must comply with national and local codes. Install the LW-401 control panel by following the steps listed below. 1. Install the enclosure. Fasten the enclosure securely to a clean, dry, shock and vibration free surface. Consider the following placement factors when mounting the enclosure: height as it
5 LW-401 Operation, Installation, and Maintenance ManualLW-401 INSTALLATION Unpacking the Equipment The LW-401 is shipped in two cartons; one of the cartons contains the LW-401 enclosure. The other carton contains the LW-401 electronics, the transformer, and the mounting hardware. Follow the proce- dure below to unpack the LW-401 equipment. 1. Locate and ope
Faraday LW401, 26 Operation, Installation, and Maintenance Manual LW-401 4ELBAT SNOITALUCLACYRETTABROFSTNEMERIUQERLACIRTCELE TNEMEGANAMREWOPDNA ybdnatS tnerruC mralA tnerruC tnerruCdraoBniaM A011.0A021.0 :)4-1senoZ(tnerruCCDI senoZCDIforebmuN =)ybdnatS(A900.0________ =)mralA(A021.0________ A______ A0 A0 A______ CANrepA5.1=<tnerruC:tnerruCeciveDCAN 1etoNeeS________1CAN ________2CAN A0 A0 A______ A______ A5.0=<tnerruC:tnerruCtroPyrailixuA 1etoNeeSeludoM8-EZWL A810.0tnerruCybdnatS A810.0tnerruCmalA syaleRdemmargorPforebmuN =A620.0x________ A______ A0 A______ A______ A600.0tnerruCybdnatSeludoMA4-EZWL A600.0tnerruCmralA syaleRdemmargorPforebmuN =A620
Faraday LW401, 2 Operation, Installation, and Maintenance Manual LW-401 Standard Components A standard four zone LW-401 has one module—the main board. An expander board is added to provide four additional zones, when needed. MAIN BOARD The Main board of the LW-401 contains the intelligence for the system and performs all of the input/output processing as listed below: • Two supervised Notification Appliance Circuits provide 24 VDC at 1.5 amps. Each circuit operates Class B (Style Y) and can be independently programmed to operate a number of different ways (Non-Coded, March Time, Temporal, or Simple Zone Code). • Two Form C relays rate
Faraday LW401, 16 Operation, Installation, and Maintenance Manual LW-401 ENABLING THE PROGRAM MODE Enter Password 1. Press the RESET key and hold it down while simultaneously pressing the DRILL key. The System TROUBLE LED turns on steady and the letter E flashes on the seven segment display. 2. Enter the password by pressing the appropriate keys (ACK = 1, RESET = 2, DRILL = 3, SILENCE = 4); then press the SILENCE key. For example, the default password is 1111. To enter the default password, press the ACK key four times and then press the SILENCE key. The seven segment display either displays F to indicate an
18 Operation, Installation, and Maintenance Manual LW-401 5. Press the Drill key to map the selected Zone to the desired Output. 6. Press the Silence key to select another Zone to be programmed and return to Step 3. 7. Press the ACK key when done. Program Level 6 - Set System Timing 1. Press the Reset key 6 times to select Program Level 6. 2. Press the Silence key
Faraday LW401, 22 Operation, Installation, and Maintenance Manual LW-401 3. Press the Drill key to change the state of the selected output. 4. Press the ACK key when done. Test Level 4 - Last Event Record 1. Press the Reset key 4 times to select Test Level 4. 2. Press the Silence key to select the event to be reviewed per the following table: Example: 4-1 reviews the last zone in alarm. Level Feature 4-1 Review Last Alarm 4-2 Review Last Zone Trouble 4-3 Review Last Verification 4-4 Review Last Supervisory 3. The Zone Alarm LED for the last zone in alarm will be on. Similarly, the Zone Troub
Faraday LW401, 13 LW-401 Operation, Installation, and Maintenance ManualLW-401 Set Output Control Matrix (Program Level 5) The LWZE-4A Zone/Output Expander mod- ule has four output relays and four open collector outputs. The LWZR-8 Relay module has eight output relays. Initiating Device Circuits can be mapped to these outputs. Any number of zones can be mapped to any output. The first zone in alarm will turn the output on. Also, any zone can be mapped to any number of outputs. When the zone alarms, all mapped outputs will t
Faraday LW401, ii List of Illustrations 1. LW-401 Control Panel ...........................................................................................................1 2. LW-401 Front Panel ..............................................................................................................2 3. LW-401 Enclosure .................................................................................................................5 4. Transformer Mounting ...........................................................................................................6 5. Mounting the Standoffs and Spacers................................................................................
Faraday LW401, 3 LW-401 Operation, Installation, and Maintenance ManualLW-401 CODE DESCRIPTION 1 AC power fail 2 NAC 1 trouble 3 NAC 2 trouble 4 Ground fault 5 Municipal tie fault 6 Battery fault 7 System Configuration fault 8 Auxiliary port fault 9 Outputs bypassed 0 Hardware failure E Enter password A Password accepted F Password fail P Program mode t Test mode L Leave Program/Test mode The Function Keys The ACK key is used to acknowledge alarms, troubles, and supervisory conditions. In general the LEDs change from pulsing to steady to indicate that the condition was acknowledged. The SILENCE key silences the notification appliance circuits that are configured as sile
Faraday LW401, 7 LW-401 Operation, Installation, and Maintenance ManualLW-401 labeled A in Figure 6, leaving a 1 /4 inch gap between the standoff and the head of the screw. b. Place the slots on the bottom of the LW41-MB on the two screws. c. Secure the board in place by fasten- ing the remaining four screws labeled B to the metal hex standoffs. d. Tighten the bottom two screws. 6. Optional modules. Refer to the specific optional module Installation Instruction sheet for the appropriate installation. 7. Before connecting any wire to its screw terminal, refer to the Checkout Procedure (page 27) and the LW-401 Connection Diagram, P/N 315- 096185FA. Prior to connectin
Faraday LW401, 20 Operation, Installation, and Maintenance Manual LW-401 4. Press the Reset key to advance the pointer (yellow zone LED) to the desired Option Card. 5. Press the Drill key to activate the desired Option Card. 6. Press the ACK key when done. Test Mode The test mode allows the user to test that the LW-401 is operating correctly. There are six levels to the test mode. Each level tests different functions within the LW-401. Reading the LW-401 Display As the system is tested, the 7-segment display shows the current test level and sublevel. When a test level is selecte
Kidde Fire Systems PEGAsys Fire Alarms Installation, operation and maintenance manual
PEGAsys |
Digital Monitoring Products XR550FC Fire Alarms Operation & user’s manual
XR550FC |
Notifier AFP-300 Fire Alarms Programming manual
AFP-300 |
Faraday MPC-6000 Fire Alarms Programming manual
MPC-6000 |
Simplex SafeLINC 4020 Fire Alarms Operating instruction
SafeLINC 4020 |
Faraday MPC-6000 Fire Alarms Programming manual
MPC-6000 |
Ansul Checkfire MP-N Fire Alarms Installation, recharge, inspection and maintenance manual
Checkfire MP-N |
Faraday MPC-6000 Fire Alarms Installation, operation and maintenance manual
MPC-6000 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Olympus | CAMEDIA D-555 Zoom | Basic manual | olympus/camedia-d-555-zoom-E48.pdf | 21 Jul 2023 | 92 | |
2 | Orion | 5520 | Manual | orion/5520-8GE.pdf | 13 Jul 2022 | 2 | |
3 | Asus | Z71 | Installation & replacement | asus/z71-7MV.pdf | 12 Mar 2023 | 13 | |
4 | Fbt | MODUS 15 | Brochure & specs | fbt/modus-15-5C3.pdf | 18 Feb 2023 | 4 | 0.59 Mb |
5 | Konica Minolta | magicolor 2480MF | Supplementary manual | konica-minolta/magicolor-2480mf-Q4H.pdf | 29 Apr 2023 | 46 | |
6 | Miller | HF-251D-1 | Owner's manual | miller/hf-251d-1-1C6.pdf | 29 Jul 2023 | 38 |
Tyco
Model RC-1 Retard Chamber For Variable Pressure Wet Pipe Sprinkler Systems 300 psi (20,7 bar) Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500Page 1 of 4 JULY 2009 TFP920General DescriptionThe Tyco® Model RC-1 Retard Chamber is required in installations that will be subject to pressure varia-tions, as are generally associated w …
RC-1(4 pages) |
EMS
©2018 EMS Ltd. All rights reserved. TSD115 Iss2 17/09/2018 AJMWireless RIMProgramming Guide
…
FireCell FCZ-170-111(22 pages) |
INIM Electronics
IFM4R 1 1 - IFM4R 2 - PRCAB + IFMABDECEN 54-2EN 54-4EN 54-21EN 12094-108320832-CPR-F1342cert. N.991KIFM4RModulo interno 4 uscite relèInternal module with 4 relay outputsMódulo interno 4 salidas reléModule interne 4 sorties relaisMódulo interno 4 saídas reléInterne module 4 relaisuitgangen
…
PREVIDIA MAX(24 pages) |
Notifier
1 I56-5921-000 INSTALLATION AND MAINTENANCE INSTRUCTIONS Model FS-WST Addressable Wall Mount Strobe Notifier by Honeywell9 Columbia Way Baulkham Hills,NSW 2153 Australiawww.notifier.com.auSPECIFICATION Item Parameter Description Note Operating Voltage DC24V( DC15V~ DC32V) …
FS-WST(2 pages) |
Evonicfires
1EVONIC - 104 INSTRUCTION MANUAL ISS. 6EVONIC - 104 INSTRUCTION MANUAL ISS. 6NEWTONNEWTONE-SmartE-SmartINSTRUCTION MANUALINSTRUCTION MANUALNewton 6Newton 6Newton 7Newton 7Newton 9Newton 9Newton 10Newton 10EnglishEnglish
…
Newton 6(22 pages) |
Autronica
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS Fire Alarm Control Panel BS-60 Commissioning handbook Program version P1-BS60-202E-0
…
AutroSafe BS-60(28 pages) |
Apogee Media Converter AD-16XApogee AD-16X Manual (Operation & user’s manual), @171YUV AD-16X, 24 |
Hanna Instruments Measuring Instruments HI 96735Manual: Hanna Instruments HI 96735 (769939, Upd.27.01.2024) HI 96735, 2 |
MTD Lawn Mower 12A-446M729MTD 12A-446M729 Guide (Operator's manual), @4262LS 12A-446M729, 20 |
Omron Other CJ1M -#U7WW6J: CJ1M - Other Brochure CJ1M -, 15 |
FUNAI LCD TV 32FW502WLCD TV Operation & user’s manual (FUNAI 32FW502W) 32FW502W, 28 |
Onkyo Receiver HT-R820THXUser Guide: Onkyo HT-R820THX (PN1MFC, Upd.16.12.2023) HT-R820THX, 141 |
Ectaco Electronic dictionary Partner EAF430TXEctaco Product Guide: Partner EAF430TX PDF Operation & user’s manual - Z1K87M Partner EAF430TX, 22 |
Weider Other Cobra 1000User Manual: Weider Cobra 1000 (96N1B3, Upd.11/12/2023) Cobra 1000, 20 |
Jet Lathe JML-1014VSJet Lathe JML-1014VS Owner's manual JML-1014VS, 16 |
Belkin Recording Equipment TuneStudioOperation & user’s manual for Belkin TuneStudio Recording Equipment TuneStudio, 108 |
PureLink Amplifier DD-250PureLink Amplifier DD-250 Owner's manual DD-250, 12 |
Studiomaster Music Mixer air pro seriesair pro series Instruction manual - 4769B4 air pro series, 12 |