Galleon 6KRT Operation & User’s Manual
|
3. Operations 3-1. Operating Mode/Status Description Mode/Status Description UPS Power On When UPS is powered on, it will enter into this mode for a few seconds for initializing the CPU and system. AC Mode When the input voltage is within acceptable range, and the UPS is turned on (the inverter is running), the UPS will provide pure and stable sine wa
Galleon 6KRT, Table of Contents 1. Safety and EMC instructions .................................................................... 4 1-1. Transportation and Storage ........................................................... 4 1-2. Preparation .................................................................................. 4 1-3. Installation ................................................................................... 4 1-4. Connection Warnings ............................................................ 5 1-5. Operation ..................................................................................... 5 1-6. Standards .....................................
6. Specifications MODEL 6KRT(L) 10KRT(L) CAPACITY* 6000 VA / 5400 W 10000 VA / 9000 W INPUT Voltage Range Low Line Loss 110 VAC ± 3 % at 50% Load; 176 VAC ± 3 % at 100% Load Low Line Comeback Low Line Loss Voltage + 10V High Line Loss 300 VAC ± 3 % High Line Comeback High Line Loss Voltage - 10V Frequency Range 46Hz
Galleon 6KRT, 3-7-2-4. Information Information displays all parameter setting value and status. Press “UP” or “DOWN” to explore the pages. 3-7-2-5. Setting This menu is used to configure the parameter settings or do the calibrations. NOTE: Some settings will be only available in some operation modes. If the setting is not available in current mode, the LCD will show prompt message with “Item can not be set in this mode”. Press any button or just wait for several seconds until this message fades.
Galleon 6KRT, regulations. Warning: ● For standard battery pack, there are one DC breaker to disconnect the battery pack and the UPS. But for other external battery pack, make sure a DC breaker or other protection device between UPS and external battery pack is installed. If not, please install it carefully. Switch off the battery breaker before installation. NOTE: Set the battery pack breaker in “OFF” position and then install the battery pack. ● Pay highly attention to the rated battery voltage marked on the rear panel. If you want to change the numbers of the batt
Galleon 6KRT, 2-3. Rack/Tower Installation 2-3-1 Tower Installation The UPS system is shipped with two sets of feet and 6 extensions (2 short extensions plus 4 long extensions) that can be used to tower install the UPS module in 3U or UPS module with one battery bank in 6U. Install UPS module in 3U Assemble two feet and one short extension as one tower stand shown in step 1. Align the two stands approximately 35cm apart in step 2. Then, put UPS module in the stands as shown in step 3. Step 1
Galleon 6KRT, 5. Storage and Maintenance 5-1. Storage Before storing, charge the UPS at least 7 hours. Store the UPS covered and upright in a cool, dry location. During storage, recharge the battery in accordance with the following table: Storage Temperature Recharge Frequency Charging Duration -25°C - 40°C Every 3 months 1-2 hours 40°C - 45°C Every 2 months 1-2 hours 5-2. Maintenance The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified maintenance personnel.
Galleon 6KRT, Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully.
Galleon 6KRT, 2. Installation There are two types: standard and long-run models. Please refer to the following model table. Model Type Model Type 6KRT Standard model 6KRTL Long-run model 10KRT Standard model 10KRTL Long-run model 2-1. Unpacking and Inspection Unpack the package and check the package contents. The shipping package contains: ● One UPS ● One user manual ● One monitoring software CD ● One RS-232 cable (option) ● One USB cable ● One parallel cable and one share current c
5) Calibration Interface Description 1. Batt: Calibrate the battery voltage measurement. Calibration range is from 0V to 5.7V. The default value is 0V. It is available on all operation modes. 2. Inv: Adjust the inverter output voltage; the adjustable range is from 0V to 6.4V, the default value is 0V. It is only available in line / battery / converter
Galleon 6KRT, 2-3-2 Rack Installation Please follow below steps to mount UPS into 19” rack or rack enclosure. Step 1: Attach mounting ears to the side mounting holes of UPS using the screws provided and the ears should face forward. Please refer to chart 1. Chart 1 Step 2: Lift the UPS module and slide it into rack enclosure. Attach the UPS module to the rack with screws, nuts and washers (user-provided) through its mounting ears and into the rack rails. Please refer to chart 2. Chart 2 2-4
Galleon 6KRT, Backup Time Parameters Setting: Batt Groups: Set the number of battery group ranging from 1 to 6. The default value is 1 group; Batt Cap: Set the battery capacity such as 7AH, 9AH, 10AH, 12AH, 17AH, 26AH, 40AH, 65AH, 100AH and so on. The default value is 9AH. Factor: Calibrate the displayed backup time by adjusting this multiplier factor. The formulation is listed below: Displayed backup time=Original calculated backup time×Multiplier factor The value of default factor is 1.0, and it ranges from 0.5 to 2. These parameters are for the battery backup time calculation
Galleon 6KRT, 1) Bypass setting Interface Description 1. Status (only available in bypass / AC mode) 1.1 Open/Forbid: Open: Bypass allowed. When selected, UPS will run at Bypass mode depending on bypass enabled/disabled setting. Forbid: Bypass not allowed. When selected, it’s not allowed for running in Bypass mode under any situations. 1.2 Enable/Disable This option appears only when Bypass status is set to “Open”. Enable: Bypass enabled. When selected, Bypass mode is activated. Disable: Bypass disabled. When selected, automatic bypass is acceptable, but “manual bypass” is not availabl
Galleon 6KRT, 3-5-9. Changing battery quantity (number) The default battery (12V) quantity of this UPS system is 20 (for one series), but 18, 19 could also be applied in this system. However, before changing the battery quantity, the UPS should be fully shutdown and the cabinet cover should be removed, and the jumpers on the control board should be re-set as below table: Note:1 = insert with jumper; 0 = no jumper; x = these pins are for other functions. NOTE: This operation should be done by professional technicians, please contact the dealer for support 3-6. Parallel UPS Operation For parallel UPS operation, please contact your
Galleon 6KRT, prolong the backup time. If there is no more load to be taken off at that time, you have to shut down all loads as soon as possible to protect the devices or save data. Otherwise, there is a risk of data loss or load failure; 2) In Battery mode, if buzzer sounds annoying, you could enter ”Control->Mute” on LCD to silence it. Please refer to the section of “LCD operation”; 3) The backup time of the long-run model depends on the external battery capacity; 4) The backup time may change under different environment temperature and load type; 5)
Galleon 6KRT, Warning 0D: Over Temp The internal temperature is too high and reach the warning level: 1) Maybe the environment is hot; 2) Maybe the fan is blocked or failed; 3) Maybe ventilation is blocked by the wall or other goods. 4) Load is too heavy. 1) Make sure ambient temperature not over 40ºC. 2) Make sure the fan is OK. 3) Make sure ventilation is well. 4) Remove some loads if possible. Warning 0E: Charger Fail Charger failed. Contact the dealer for repair. Warning 10: IP Fuse Open Input fuse on the power stage board is
Galleon 6KRT, 1. Safety and EMC instructions Please read carefully the following user manual and the safety instructions before installing the unit or using the unit! 1-1. Transportation and Storage Please transport the UPS system only in the original package to protect against shock and impact. The UPS must be stored in the room where it is ventilated and dry. 1-2. Preparation Condensation may occur if the UPS system is moved directly from cold to warm environment. The UPS system must be absolutely dry before
Galleon 6KRT, Move the arrow to “Yes” by up or down button, then press “ON/ENTER”, the UPS will be starting up with beeping once. You could also enter the “control menu” to select the instruction “Turn On” to startup the UPS. Please refer to the section of “LCD operation”. 3) A few seconds later, the UPS will enter into Line mode; “Line mode” will be displayed on LCD. (In line mode, if the utility power is abnormal, the UPS will transfer to Battery mode without interruption.) 3-5-2. Turn on the UPS without utility power supply (to Battery mode) 1) Ma
Galleon 6KRT, time since this would cancel the protective earth of the UPS system and of all connected loads. If the external battery cabinet is connected, the UPS output Anderson connector may be electrically live even if the UPS system is not connected to the building wiring outlet. In order to fully disconnect the UPS system, first press the “OFF” button and then disconnect the mains. Ensure that no liquid or other foreign objects can enter into the UPS system. The UPS can be operated by any individuals with no previous experience. 1-6. Standar
E&C Cheerups 600 UPS Installation manual and operators instructions
Cheerups 600 |
CyberPower RMCARD305 UPS Operation & user’s manual
RMCARD305 |
Powerware 9330 UPS Installation & operation manual
9330 |
Xtreme 1000VA UPS User & installation manual
1000VA |
Tripp Lite HT1000UPS UPS Owner's manual
HT1000UPS |
Galleon 1K UPS Operation & user’s manual
1K |
Actidata actiLib Autoloader 1U UPS Quick start manuals
actiLib Autoloader 1U |
Dell PowerVault Storage Area Network UPS Manual
PowerVault Storage Area Network |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Avocent | SwitchView SwitchView DVI | Brochure & specs | avocent/switchview-switchview-dvi-TOV.pdf | 09 Oct 2022 | 8 | 0.6 Mb |
2 | HSY | F107E | Operation & user’s manual | hsy/f107e-EPI.pdf | 02 Mar 2024 | 2 | |
3 | VarTech Systems | VT29B-M | Operation & user’s manual | vartech-systems/vt29b-m-366.pdf | 25 Mar 2023 | 17 | |
4 | Teltonika | T-Wireless COM | Operation & user’s manual | teltonika/t-wireless-com-9PC.pdf | 11 Jul 2023 | 16 | |
5 | Lafayette | ZEUS | Operation & user’s manual | lafayette/zeus-YLH.pdf | 21 Aug 2022 | 16 | |
6 | Sony | HCD-SD1 | Service manual | sony/hcd-sd1-O3K.pdf | 02 Oct 2023 | 51 |
SafeCom
Power Safecom T-Former Series Stabilized pure sine voltage technology ( US Patent 8,415,822) Safecom TFPS Series Installation Manual FEB-2015 SAFECOM US Patent 8,415,822. 1
…
T-Former Series(15 pages) |
Toshiba
UNINTERRUPTIBLE POWER SYSTEM (UPS) G9000 SERIES INSTALLATION AND OPERATION MANUAL 480/480 V 1000kVA Document No.: 91649-0041 Reference: 4GBA0051 Rev. A September. 2014
…
G9000 SERIES(72 pages) |
S&C
May 29, 2018© S&C Electric Company 2017-2018, all rights reservedInstruction Sheet 659-555S&C PureWave® SMS-250 Storage Management System263 kW/263 kVA, 380 VPower Conversion SystemTable of ContentsSection Page Section PageIntroductionQualified Persons ..............................2Read this Instruction Sheet ......................2Retain this I …
PureWave SMS-250(16 pages) |
Centralion
UNINTERRUPTIBLE POWER SYSTEM SERVICE MANUAL Blazer series 400VA,600VA and 800VA Model: 400VA: 400VA/115V,400VA/230V 600VA: 600VA/115V,600VA/230V 800VA: 800VA/115V,800VA/230V 115V/220V/230V/240V 50Hz/60Hz Prepared by:FulinApril 9, 2002
…
400VA(33 pages) |
Victron energy
®TDS | QUICK GUIDEVictron MultiPlusInverter/Charger Battery Back-Up - 500VA to 1600VAPage 1 of 12© Newton Waterproofing SystemsNewton House, 17-20 Sovereign WayTonbridge, Kent, TN9 1RHwww.newtonwaterproofing.co.uktech@newtonwaterproong.co.uk+44 (0)1732 360 095Opening Hours:Monday to Thursday 8:00am - 5:30pmFriday 8:00am - 5:00pmRevision 1.0 - 17th …
Multiplus(12 pages) |
Tripp Lite
Owner’s Manual1111 W. 35th Street • Chicago, IL 60609 USA(773) 869-1234 • www.tripplite.comCopyright ©2007 Tripp Lite. All rights reserved. SmartOnline™ is a trademark of Tripp Lite.Important Safety WarningsFront PanelInstallationRear PanelService235617Operation (Normal Conditions)7Operation (Special Conditions)9Communications10Warranty17Specificati …
Power Supply(56 pages) |
Samsung Flat Panel TV PPM42M8HBPPM42M8HB (Flat Panel TV ePDF Manual, #94JKY8) PPM42M8HB, 2 |
Heat Wise Burner SU-2AProduct manual for Heat Wise SU-2A Burner SU-2A, 16 |
Singer Sewing Machine 107W50Sewing Machine Instructions for using and adjusting (Singer 107W50) 107W50, 11 |
Oracle Storage StorageTek T10000Oracle Storage StorageTek T10000 Operator's manual StorageTek T10000, 132 |
IMG STAGE LINE Spotlight Leuchtkraft ODC-100/CTWIMG STAGE LINE Spotlight Leuchtkraft ODC-100/CTW Instruction manual Leuchtkraft ODC-100/CTW, 35 |
Whirlpool Oven W10351242BPDF Guide (@5A15AV), Whirlpool W10351242B Oven (30th Sep 2023) W10351242B, 16 |
Samsung Digital Camera TL500TL500 Manual del usuario - XKKC25 TL500, 129 |
Philips Headphone SBCHP090/02User Manual: Philips SBCHP090/02 (14K142, Upd.Friday 29-09-2023) SBCHP090/02, 2 |
UltraLite Work Light ALS TurboWork Light Operator's manual (UltraLite ALS Turbo) ALS Turbo, 16 |
Audiovox Car Receiver AVXMTGHR1DAAVXMTGHR1DA Operation manual - H265P1 AVXMTGHR1DA, 29 |
Sigma Camera Lens APO 70-300mm F4-5.6 DG MACROInstructions for Sigma APO 70-300mm F4-5.6 DG MACRO Camera Lens APO 70-300mm F4-5.6 DG MACRO, 4 |
Godrej Air Conditioner GSC 18 FGA 5 WOGGodrej Product User Guide: GSC 18 FGA 5 WOG PDF Service manual - 72Z4A2 GSC 18 FGA 5 WOG, 23 |