Digital Information Preproofer 940 Installation Manual

Text of Digital Information Preproofer 940 User Guide:

• 4 Assemble the System Installation Steps 4-8 Preproofer – HW Installation manual . Check the position of the AntiCurling device. When the bar is in the lowest position, it should not touch the blue paper roll side holders. 14.) Insert the 6” media side guides onto the roll media spindle. Load the roll media paper edge coming under the spi

• Digital Information Preproofer 940, 4 Assemble the System Installation Steps 4-10 Preproofer – HW Installation manual . 17.) Load the paper media through the anti-curling bar. Feed paper through the metal rod and around the metal plate and into the epson printer slot. (1) Metal rod (2) Metal plate 18.) Unsnap the black plastic guides inside BOTH the Epson machines (5 or 7 pieces in each machine). (1) Plastic Guide 19.) In the lower printer, remove the 2 of 5 screws (second screw from the left and second screw from the right) in the lower

• Digital Information Preproofer 940, Function test Installation Steps 5 Preproofer – HW Installation manual 5-1 . 5 Function test Before installing and configuring the software components, test the system like: 1) Go through the sw installation check list from the document “Quick Start SW for Preproofer ACAPULCO x400 x800 english.pdf” to correctly install the necessary programs for the shufflebox. Start the sw EPS100605. 2) PRINTER FRONT Set on the control panel to “Roll paper cut” 3) PRINTER BACK Set on the control panel the paper to “Sheet” 4) PRINTER FRONT Load the 6” paper roll on the top printer 5) PRINTER FRONT On the control panel, press the paper feed but

• Digital Information Preproofer 940, 4 Assemble the System Installation Steps 4-6 Preproofer – HW Installation manual . (2) Left side roll holder: remove 2 screws 11.) In the Top printer, remove 3 or 5 screws holding the back cover. (1) Remove screws (2) Back Cover 1 1 1 1 1

• Digital Information Preproofer 940, Assemble the System Installation Steps 4 Preproofer – HW Installation manual 4-5 . 8.) Glue the Vertical cable channel behind the side legs. (1) Vertical cable channel 9.) On each Epson printer, remove the plastic media deflectors (3 or 5 on each printer) by opening the front cover and unscrewing 2 screws on each deflector. (1) Front Cover (2) Plastic media deflector 10.) On the Top printer remove the right side roll holder by removing 3 screws and the left side roll holder by removing 2 screws. Remove the plastic cover. Reassemble again both the right side roll holder and left side roll holder. (1) Right side roll ho

• Digital Information Preproofer 940, Digital Information Ltd. Technoparkstrasse 1 CH-8005 Zürich © Copyright by Digital Information Ltd. 2006 This manual is proprietry in nature and the sole property of Digital Information. It may not be reproduced, in whole or in part, without the express written permission of Digital Information. Digital Information reserves the right to modify and/or delete any material and/or capabilities described herein. All the documentation in this manual is instructional and for the operation of Preproofer

• Digital Information Preproofer 940, Assemble the System Installation Steps 4 Preproofer – HW Installation manual 4-7 . 12.) In each location of screws removed, insert round plastic washer and screw with new elongated screws. Do not tighten screws. ( 1) Plastic washer with new screw 13.) Insert the Anti-curling device tighten it with new screws. (1) Anti-curling device 1 1 1 1

• Digital Information Preproofer 940, 4 Assemble the System Installation Steps 4-4 Preproofer – HW Installation manual . 4.) Insert the upper shelf and tighten it with 2 screws, washers and nuts on each side. 5.) Insert the lower shelf and tighten it with 2 screws, washers and nuts on each side 6.) Glue the lower cable channel underneath the bottom shelf. (1) Cable Channel (2) Hole for Power Supply Shuffle Box, Ethernet cable (3) Hole for USB Cable (4) Open end for mains cable 7.) Glue the upper cable channel underneath the bottom of the top shelf. (1) Hole for

• Digital Information Preproofer 940, Introduction Warning 1 Preproofer – HW Installation manual 1-1 . 1 Introduction The Preproofer 940/980 is a fully automatic system printing double-sided proofs in 8up format. The system is based on two Epson Stylus 9400/9800 printing engines, enabling print widths of 111cm (44”). The Preproofer 740/780 is a fully automatic system printing double-sided proofs in 4up format. The system is based on two Epson Stylus 7400/7800 printing engines, enabling print widths of 61cm (24”). Please note: Installation of this equipment must be done by a tr

• Digital Information Preproofer 940, Assemble the System Installation Steps 4 Preproofer – HW Installation manual 4-9 . 15.) Position the Bottom Epson Printer on the bottom shelf with the threaded hole underneath the printer aligned over the shelf hole. Take the printer locking device (large plastic spaced, thin plastic washer and long screw). Insert the plastic spacer in between the printer and the shelf and align it in centre to the shelf hole and the printer hole. Insert the long screw into the thin plastic washer and screw it from underneath the shelf. (1) Large plastic washer (2) Thin plastic washer Caution: Do not leave the printer on the stand without securing it

• Digital Information Preproofer 940, Assemble the System Installation Steps 4 Preproofer – HW Installation manual 4-17 . 36.) Disconnect the Y-Motor connector with 2 pins on the Epson CPU Board and reconnect female connector of the cable to the male connector on the CPU Board. (1) Y-Motor connector with 2 pins 37.) Connect the 2 wire Male connector to the Y-Motor female connector. (2) 2 wire male connector to Y-Motor female connector. 38.) Route the cables for the lower printer through the cable channel as shown. 39.) Route the cables for the Lower printer through the cable channel . 1 1

• Digital Information Preproofer 940, 4 Assemble the System Installation Steps 4-16 Preproofer – HW Installation manual . 32.) Connect the keypad cable (4 pin plug) to the Interface Box. 33.) Connect the Y-Motor cable (5 pin plug). The wires should look as shown. (1) 5 pin plug (2) 4 pin plug 34.) Reclick the keypad very carefully. 35.) 1 1

• Digital Information Preproofer 940, Table of contents Preproofer – HW Installation manual I . Table of contents 1 Introduction ............................................................................................................... 1-1 2 Safety ...................................................................................................................... 2-1 2.1 Warning............................................................................................................................................ 2-1 3 Tools and Materials requi

• Safety Warning 2 Preproofer – HW Installation manual 2-1 . 2 Safety This section provides important safety information and must be read before switching on or operating the equipment. 2.1 Warning All precautions mentioned in this document must be strictly observed at all times. Personnel MUST therefore read the contents of the document BEFORE commencing any work o

• 4 Assemble the System Installation Steps 4-14 Preproofer – HW Installation manual . 28.) Remove the top screws on the back cover of the lower printer. (1) Top sc re ws 29.) Remove screws on the back. (1) screws on the back 1 1 1 1 1

• Digital Information Preproofer 940, 4 Assemble the System Installation Steps 4-18 Preproofer – HW Installation manual . 40.) Connect the 9 pin ethernet cable to the connector on the Interface Box. (1) Connect to Power Supply (2) Ethernet Cable 41.) Attach Ethernet cable from the PC to the Epson interface Box. 42.) Connect the Power Supply cable.Minimum of 12 V supply is required for the interface box to work. The power supply should be able to deliver minimum of 1.5A. (1 )The green lamp on the Ethernet connector will be lit. 43.) Align b

More Instructions:

Digital Information Preproofer 940 Installation manual 10-12-2022 35

DOWNLOAD

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• HP FM892UT#ABA - TouchSmart Tx2-1032cm - Turion X2 Ultra 2.3 GHz (2 pages) Q7523AQ7521AInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallQ7521A, Q7522A, Q7523AInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInstallInst …

• DataCard SP75 Plus (12 pages) Quick Install GuideSP75 Plus Card PrinterNetwork InstallationUSB Installation (over)Quick Install GuideSP75 Plus Card PrinterUSB InstallationNetwork Installation (over) …

• HP C8187A (4 pages) HP Officejet Pro L7000 Series All-in-One Printer, Fax, Scanner, Copier L7580 • L7680 • L7780 Print at breakthrough speeds • Bring color speeds and proven HP performance into your office. Print at up to 35 pages per minute (ppm) black and up to 34 ppm color. • Produce professional-quality documents. Conveniently and efficiently create h …

• HP LaserJet P4014 (22 pages) HP®P4014 • P4015 • P4045CARTRIDGE REMANUFACTURING INSTRUCTIONSCC364X TONER CARTRIDGECC364A TONER CARTRIDGE3232 West El Segundo Blvd., Los Angeles, California 90250 USA • Ph +1 310 280 9620 • Fx +1 310 838 7294 • [email protected] • www.uninetimaging.com© 2008 UniNet Imaging Inc. All Trademark names are property of their respecti …

• HP DesignJet Z2600 (28 pages) © Copyright 2016 HP Development Company, L.P.Large Format DivisionCamí de Can Graells 1-21 · 08174Sant Cugat del VallèsBarcelona · SpainAll rights reservedPrinted in XXX*T0B52-90006*T0B52-90006HP DesignJet Z2600 PostScript® PrinterProduct Assembly Instructionsセットアップ 手 順组装说明印表機組裝說明프린터 조립 지침Petunjuk Pe …

• Dascom DP-330L (26 pages) DP‐3ThDASCw330Dherm COM EuropHeuweg 89168 UlGermanwww.dascom SerOpeDP-3mal pe GmbH 3 lm y m.com iesrator’s330Pri sManunte ualr 3799 925b …

Comments, Questions and Opinions: