DIGITAL YACHT iNavHub Installation & Quick Start Manual

Text of DIGITAL YACHT iNavHub User Guide:

• DIGITAL YACHT iNavHub, DIGITAL YACHT LTD iNavHub Quick Start Guide 1. Introduction Congratulations on the purchase of your iNavHub Wireless Router. It is recommended that your router is installed by a professional installer. If the iNavHub is to be connected to the internet via a Digital Yacht WL510 long range Wi-Fi Adaptor it is recommended that this installation/configuration is carried out by someone with suitable IT experience and knowledge of ethernet networks. The iNavHub can be used in the following configurations; 1)

• DIGITAL YACHT iNavHub, DIGITAL YACHT LTD iNavHub Quick Start Guide  To fit an SMA Extension cable, unscrew the 5dB antenna from the iNavHub and screw the extension cable between the iNavHub and the antenna. Now you will be able to hide the iNavHub unit behind a bulkhead and mount the antenna in the cabin for maximum Wi-Fi range.  Provide power connections to the unit from the boat’s supply. Power is connected to the iNavHub’s two core Power cable on the Red and Black wires. The Red wire is the positive

• DIGITAL YACHT iNavHub, DIGITAL YACHT LTD iNavHub Quick Start Guide Installation Step 4  The following steps only need to be followed if you are connecting the iNavHub to an NMEA 0183 device on the boat. The iNavHub is pre-configured to handle data at 38400 baud which is the high speed NMEA 0183 format used by AIS units and NMEA Multiplexers. If you wish to use the iNavHub with standard 4800 baud NMEA equipment, you will need to download and install the AISNet Configuration tool. http://www.digitalyacht.co.u

• DIGITAL YACHT iNavHub, DIGITAL YACHT LTD iNavHub Quick Start Guide 4. Network Configuration Digital Yacht have pre-configured the iNavHub so that in most situations it will work straight out of the box with no additional configuration required. The iNavHub default settings are as follows; IP Address - 192.168.1.1 Subnet Mask - 255.255.255.0 DHCP Range - 10.22.0.0 to 10.22.0.255 SSID - iNavHub Password - inavhubpass The choice of IP addresses is suitable for most situations, but if you wish to change this or change the SSID and password then this can be done by any device connected to the iNavHub by

• DIGITAL YACHT LTD iNavHub Quick Start Guide 5. Sharing Long Range Wi-Fi Connection When you use the iNavHub with the Digital Yacht WL510, all routing of the wireless connections to the internet are automatically configured. After you have connected wirelessly to the iNavHub as detailed in section 4, you should be able to display the WL510 login page by

• DIGITAL YACHT iNavHub, DIGITAL YACHT LTD iNavHub Quick Start Guide To test and prove that the system is working, you can download our free iAIS app from the Apple store and the following guide assumes that you have already done this. Go to the Settings>Wi-Fi and ensure that your device is wirelessly connected to the iNavHub network. Run iAIS and go to the Instruments>Setup>TCP/IP menu. Select UDP mode, Port 2000 and then switch the Link button to ON. You should now see the raw NMEA 0183 data being received in the monitor window as shown below; This proves that the iNavHub is correctly converting NMEA 0183 data to wireless data which can be used in any UDP compati

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• Ublox NINA-W1 Series (55 pages) UBX-17005730 - R11 C1 - Public www.u-blox.com NINA-W1 series Stand-alone Wi-Fi and multiradio modules System integration manual  Abstract This document describes the system integration of NINA-W1 series stand-alone modules, which includes the NINA-W13 (Wi-Fi) and NINA-W10 and NINA-W15 series (multiradio) modules. These modules feature a …

• NETGEAR MBR624GU - 3G Mobile Broadband Wireless Router (2 pages) )NSTALLATION'UIDE3G Mobile Broadband Wireless Router MBR624GUYour wireless 3G/UMTS USB modem (sold separately) must be activated before you install the router. For a list of compatible wireless USB modems, see the NETGEAR website at http://www.netgear.com/3G. To configure the router during installation, you need a computer with an Ethernet port. Your …

• EnGenius ETR9350 (16 pages) Quick Start Guide – ETR9350 Wireless Broadband Router. 1 ETR9350 3G Travel Router Quick Start Guide Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, the router automatically enters the self-test phase. During self-test phase, Power LED will blink briefly, and then will be lit continuously to indicate …

• Atatech BT402 (2 pages) ATATECHIndustryLimited Bluetooth4.0www.atateches.comEmail:[email protected] ThankyouforpurchasingaBluetoothDongleBT402productandwehopeyouenjoyusingit.Installation Steps: 1. Uninstall previous version of BlueSoleil …

• LG BP530 (68 pages) OWNER’S MANUALSmart 3D Blu-ray Disc™PlayerPlease read this manual carefully before operating your set and retain it for future reference.www.lg.comBP530P/NO : SAC35673302 …

• Ubiquiti UDM (9 pages) UDM AC Power CordPackage ContentsSystem RequirementEither of the following is required:iOS or Android™ Mobile Device with UniFi Network App InstalledWeb Browser: Google Chrome (Other browsers may have limited functionality)IMPORTANT: We strongly recommend using UPS backup and powerregulation to prevent equipment damage due to stability issues withlocal AC …

Comments, Questions and Opinions: