Manualios.com

Emulex LP8000 Installation And Reference Manual

Emulex LP8000 Manual Online:

4.4, 1721 votes
Emulex LP8000 User Manual
Emulex LP8000 User Guide
Emulex LP8000 Online Manual

Text of Emulex LP8000 User Guide:

  • Emulex LP8000, The reader is cautioned that any changes or modifications to the equipment not expressly approved by Emulex could void the user’s authority to operate this equipment. This class B digital apparatus meets all requirements of the Canadian Interference − Causing Equipment Regulations. Cet Appareil numerique de la classe B respecte toutes les exigences du reglement sur le material brouilleur du Canada. The above statement applies to products marketed in Canada. VCCI Notices and Translations (Japan Only) Note VCCI regulations provide that changes or modifications not expressly approved

  • Emulex LP8000, Hardware Reference Copper Port (DB9) Pinout This pinout applies to embedded copper ports. Pin Signal Direction 1 TX+ Output 2 VCC VCC 3 Fault - Input 4 Key NC 5 RX+ Input 6 TX- Output 7 ODIS + Output 8 GND GND 9 RX- Input

  • Install Host Bus Adapter Board Record IEEE address and serial number. Each host adapter is shipped with a unique address identifier called the IEEE address. The Fibre Channel industry uses a World Wide Name (WWN) derived from the IEEE address, and this number is need for arbitrated loop connectivity. The serial number is used when communicating with Emulex. Both numbers ar

  • Emulex LP8000, GLM The GLM is designed and certified for applications using point−to−point optical fiber links only. Use of the product with multiple input or multiple output optical links (for example, star couplers) is prohibited since it is incompatible with the GLM’s certification. The GLM will not allow normal data transmission on the optical link unless it is connected to another similar GLM or compatible laser product. For OFC GLMs, another manufacturer’s laser product is not considered compatible unless it contains the open fiber link

  • Emulex LP8000, Class 1 laser product. Any system level product that incorporates the small form factor transceivers must provide power supply protection that guarantees a voltage of 5.0 volts or less at the small form factor transceivers. The functional power supply range of the small form factor transceivers product is specified as 3.135 to 3.465V typically. Operation outside of this range may degrade the performance and lifetime of the transceiver. The transceiver will remain operational with laser emissions below Class 1 limits provided the power supply

  • Emulex LP8000, Manual Notice Translation: This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Emulex Drivers, Software and Manuals 16

  • maintenance, service operations or adjustments can be performed the GBIC. Small Form Factor Transceiver The small form factor transceiver is an integrated duplex data link for bi−directional communications over multimode or single mode optical fiber. Each small form factor transceiver consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains a semiconduc

  • Emulex LP8000, This equipment complies with CISPR22/EN55022 Class A. Warning This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. This Declaration identifies the product, manufacturer's name and address, and applicable specifications recognized in the European Union. DECLARATION OF CONFORMITY Manufacturer: Emulex Corporation 3535 Harbor Blvd. Costa Mesa, CA 92626 USA declares under sole responsibility that the product: Product Name: LightPulse™ LP8000 Fibre Channel PCI Host Adapter Assembly Number: FC1020019−XX (Embedded DB9 model) to

  • Emulex LP8000, In Europe, all optical GLMs, GBICs, 1x9 and small form factor transceivers sold by Emulex are certified as Class 1 laser component assemblies that conform to the requirements contained in the CENELEC (European Committee for Electrotechnical Standardization) standard EN60825−1:1994 (including amendment 11) and EN60825−2:1994. GLMs, GBICs, 1x9 and small form factor transceivers are certified by a recognized European testing agency and have appropriate markings on the assembly. The DHHS conformity label and European conformity mark will not be visible externally once the optical GLM, GBIC, 1x

  • Emulex LP8000, Attach Media Attach fibre optic or copper cable to the host bus adapter. Attach Fiber Optic Cable (Multi/Single Mode) Note The host adapter will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode.) Use fiber optic cable supporting a data rate of 1.0625 Gb/s for short−wave and long−wave lasers, that adheres to the following specifications: Fiber Optic Cable Maximum Length Minimum Length Connector 62.5/125 �

  • Emulex LP8000, Attach Copper Duuplex Cable Use copper Twinax or Quad Axial cable that adheres to the following secifications: Cable Type Maximum Length Data Rate Connector Twinax or Quad Axial 30 meters 1.0625 Gb/s DB9 Connect the copper duplex cable to the DB9 connector on the host adapter board as shown. 1. Connect the other end of the cable to the Fibre Channel device.2. After the media is connected to the host adapter, you are ready to apply power to the computer. Emulex Drivers, Software and Manuals 8

  • Emulex LP8000, FCC Compliance Information Statement; Model LP8000−F1 (1 X 9): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535 Harbor Blvd., Costa Mesa, CA 92626, USA, (714) 662−5600 Note: This equipment has been tested and found to comply with the

  • Emulex LP8000, Installation Caution Emulex LightPulse Host Bus Adapters (HBAs) contain electronic components that can be damaged by static electricity through an electrostatic discharge (ESD) event. To prevent ESD damage, maintain frequent contact with any grounded metal surface. A grounding wrist strap is useful for this purpose. Handle the card carefully at all times and preferably by the edges. Avoid touching electronic components and keep the card in the original packaging until you are ready for installation. Compatibility Software Environments

  • Emulex LP8000, Change the GBIC Connector A GBIC, or Gigabit Interface Converter, is a connector that offers a flexible choice of copper or fiber optic media. A GBIC supports either short wave or long wave optical transmission. These types are available: Short−wave fiber optic GBIC with dual SC connectors• Long−wave fiber optic GBIC with dual SC connectors• Copper GBIC with DB9 connector• Caution An Emulex supplied GBIC is required to maintain regulatory compliance with worldwide certifications (for example, FCC, C−Tick, CE, and so on). A GBIC should be matched with its cabling to obtain op

  • Emulex LP8000, System Level Certification All GLMs and GBICs sold as accessories by Emulex or host adapters containing embedded 1x9 or small form factor transceivers are certified as Class 1 laser products within the U.S. and Class 1 laser component assemblies outside of the U.S. Manufacturers of products properly incorporating the GLM, GBIC, 1x9 or small form factor transceiver do not need to recertify their product for laser safety. The procedure for full system certification is therefore identical to that used for any other electronic system. When applying for system level certification

  • Emulex LP8000, Hardware Reference FCC and Regulatory Notices CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A` LASER DE CLASSE 1 TO IEC 825−1 (1993) + CENELEC HD 482 S1 The above statement applies to products marketed in the European Union. Model LP8000−D1 (Embedded Copper) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfere

  • Set Jumpers The host adapter has two jumper blocks (JX1, JX2) that control the host adapter's device ID. The default Device ID is F800. Device ID Jumper Setting F800 JX1:1−2, JX2:2−3 F801 JX1:2−3, JX2:1−2 1AE5 JX1:2−3, JX2:2−3 Emulex Drivers, Software and Manuals 4

  • Emulex LP8000, Apply Power Verify that the host adapter is securely installed in the computer.1. Verify that correct media is attached.2. Plug in and turn on the computer.3. Observe LEDs for Power On Self Test (POST) results.4. View LEDs Green and yellow display lights (LEDs) can be seen through openings in the host adapter's mounting bracket. Green indicates power and yellow signifies port activity. A third LED is present on LP8000 models with embedded optical interfaces, and indicates that light is being received by the port. POST conditions and results are summarized in this table. Gre

  • Emulex LP8000, Hardware Reference Declaration of Conformity Note Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment. DECLARATION OF CONFORMITY Manufacturer: Emulex Corporation 3535 Harbor Blvd. Costa Mesa, CA 92626 USA declares under sole responsibility that the product: Product Name: LightPulse™ LP8000 Fibre Channel PCI Host Adapter Assembly Number: FC1020017−XX (GBIC model) FC1020016−XX (embedded optical, 1x9 model) Accessories: Emulex PN 2300029 (Active Copper DB9 GBIC Module) Emulex PN 2300028 (Shortwave Optical GBIC Module) Emulex PN 2300030 (Longwave Optical GBIC

Related Products and Documents (PCI Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Yamaha PSR-210 Manual de instrucciones yamaha/psr-210-247.pdf 23 Jun 2022 29 2.59 Mb
2 Bissell 1313 Series Operation & user’s manual bissell/1313-series-68V.pdf 17 Sep 2022 12
3 Sharp 32C241 Operation manual sharp/32c241-QJ7.pdf 24 Aug 2022 47 1.47 Mb
4 Rival SC7500-IUK Instruction manual rival/sc7500-iuk-SX1.pdf 30 Jul 2022 5 0.19 Mb
5 Krell Industries MD2 Owner's reference manual krell-industries/md2-12I.pdf 22 Oct 2022 13
6 Aleratec DVD/CD Flash Copy Tower Operation & user’s manual aleratec/dvd-cd-flash-copy-tower-ULV.pdf 24 Feb 2024 38 2.08 Mb

Similar Resources:

  • Broadcom

    BCM94301MPL

    (60 pages)
    Contents: Broadcom BCM94301MPL Internal 802.11b Mini PCI Card User's GuideBroadcom BCM94301MPL Internal 802.11b Mini PCI Card User's GuideIntroductionCompleting the SetupUsing the Broadcom BCM94301MPL Wireless UtilitySpecificationsRegulatory InformationTroubleshooting Glossary Information in this document is subject to change without notice.© Copy …
  • ADLINK Technology

    PCIe-7432

    (32 pages)
    Advance Technologies; Automate the World.Manual Rev.: 2.00Revision Date: Jan. 29, 2016Part No: 50-11259-1000PCIe-743232CH Isolated DI/32CH Isolated DOPCIe Card …
  • LaCie

    eSATA PCI Card

    (1 pages)
    Mac HD12Mac HD2Mac HDMac HDeSATA HubTHUNDERBOLT™ SERIES112Mac HDMac HDMac HDLaCieeSATA3 4100% RecyclableCopyright © 2012, LaCie 120113Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation in the U.S. and/or other countries.3www.lacie.comwww.lacie.com/registerhttp://manuals.lacie.com/esata-hub www.lacie.com/products/warrantywww.lacie.c …
  • ADLINK Technology

    NuDAQ-2500 Series

    (64 pages)
    Advance Technologies; Automate the World.Manual Rev. 2.01Revision Date: December 21, 2006Part No: 50-12265-100NuDAQ-2500 SeriesHigh PerformanceAnalog Output Multi-function CardsUser’s Manual …
  • Yeastar Technology

    TDM800

    (2 pages)
    TDM800 Instruction - 1 - Hardware Installation In order to successfully install the TDM800 card into your PC, please follow these directions carefully. Otherwise, your hardware maybe will not function properly and could become damaged. Steps 1. Pow …
  • D-Link

    DWA-X3000

    (2 pages)
    • DWA-X3000 || AX3000 Wi-Fi 6 PCIe Adapter with Bluetooth® 5.1 • 2 x High Performance Antennas• Magnetized Antenna Base with 3 ft (1 m) RF Cable• Low Profile Bracket• Bluetooth® Header Cable• Quick Installation Guide• CD-ROMENGLISHPACKAGE CONTENTSQuick Installation GuideDWA-X3000AX3000 Wi-Fi 6 PCIe Adapter with Bluetooth® 5.1INSTALLA …

Comments, Questions and Opinions: