ADTRAN 1200080L1 Operation & User’s Manual
|
ADTRAN 1200080L1, Appendix B. Signaling States Vs. Mode of Operation 61200.080L1-1 FXS+ Dual Voice Option Module 31 See Tables B-C and B-D for descriptions of FXS mode for signaling states. Table B-C FXS+ Mode (Loop-Start) FXS FXS+ 2W Input RX A RX B TX A TX B 2W Output (Outgoing call from FXS+) Loop Open X 1 0 1 No Ringing (Idle) Loop Closed X 1 1 1 No Ringing (Incoming call to FXS+) Loop Open X 0 0 1 Ringing Loop Closed X 0 1 1 No Ringing The A and B signal bit states on the DS-1 signal are as follows: 0 = logic 0 is the DS-1 stre
ADTRAN 1200080L1, Chapter 3. Operation 16 FXS+ Dual Voice Option Module 61200.080L1-1 2W STATUS (2-Wire Status) There are three information fields, Busy, Ringing, and MW (message waiting). See Figure 3-3. An asterisk (*) indicates an item is active. Figure 3-3 2-Wire Status Display Busy An asterisk is present if loop current is flowing through the 2-wire circuit. Ringing An asterisk is present if ringing voltage is being applied to the 2-wire circuit from the ring-generator on the FXS+ option module. Message Waiting (MW) An asterisk is present if the card i
ADTRAN 1200080L1, Chapter 2. Installation 61200.080L1-1 FXS+ Dual Voice Option Module 9 Modules Without Hot Replaceable Label on Back Panel Power to the TSU 100/600 must be Off when installing or removing the FXS+ Dual Voice option module without a Hot Replaceable label on the back panel. Placement of the Option Module Figure 2-1 represents the action required for proper placement of the option module. 1. Remove cover plate from the TSU 100/600 rear panel. 2. Slide option module into the rear panel until it is positioned firmly against the
ADTRAN 1200080L1, Chapter 3. Operation 14 FXS+ Dual Voice Option Module 61200.080L1-1 Once the option module is selected, the FXS+ menus appear as a subset of, and operate the same as, menus for the TSU 100/600. With the cursor on one of the TSU 100/600 four main menu choices press Enter or a menu number to display the first two submenu items. Use the up and down Arrows to place the cursor on the desired item and press Enter to display the first two submenu choices. TSU 100 MAIN MENU 1)STATUS 2)CONFIG 3)UTIL 1)NI PERF REPORTS 2)NI ERRORS 3)ACTIVE ALARMS 4)VIEW HISTORY 5)PORT STATUS
Chapter 1. Introduction 4 FXS+ Dual Voice Option Module 61200.080L1-1 FXS+ Option Module Specifications The FXS+ Dual Voice option module conforms to the following specifications: Voice Channels 2 (4 with plug-on module installed) Transmission Levels TX: +3 to -5 dB TLP, 1 dB steps RX: 0 to -8 dB TLP, 1 dB steps Frequency Response 300 - 3400 Hz (± 1.0 dB) 2-wire Impedance 600 Ω + 2.15 µF
ADTRAN 1200080L1, Chapter 3. Operation 18 FXS+ Dual Voice Option Module 61200.080L1-1 Port Configuration Menu Items and Their Choices Mode Mode sets the type of 2-wire to T1 signaling and super- vision to be used. Choices include: • FXS_LS This mode sets the port to use FXS loop-start type signaling on the T-Span and loop-start supervision on the analog 2-wire interface. This mode supports far- end disconnect by removing tip-ground during the call if signaled to do so over the T-span. When used with an ADTRAN FXO+, this feature allows line-curre
ADTRAN 1200080L1, Chapter 2. Installation 61200.080L1-1 FXS+ Dual Voice Option Module 7 Chapter 2 Installation UNPACK AND INSPECT Carefully inspect the FXS+ Dual Voice option module for any shipping damages. If damage is suspected, file a claim immediately with the carrier and then contact ADTRAN Customer Service. If possible, keep the original shipping container for use in shipping the FXS+ module back for repair or for verification of damage during shipment. Shipped by ADTRAN The following items are included in the ADT
ADTRAN 1200080L1, Chapter 3. Operation 61200.080L1-1 FXS+ Dual Voice Option Module 19 disconnect supervision. This mode also requires other options to be selected. These options are: supervi- sion, dial tone, loop reverse battery, and ringback. These options are described in detail elsewhere. Ringing cadence for incoming calls is two seconds on, four seconds off. • TANDEM_GS This mode sets the port to use E&M signaling on the T-Span and ground start supervision on the analog 2-wire interface. Ground-start operation is often used with trunk interfaces to PBX and key systems to prevent glare conditions. Approp
ADTRAN 1200080L1, Appendix B. Signaling States Vs. Mode of Operation 32 FXS+ Dual Voice Option Module 61200.080L1-1 Table B-D FXS+ Mode (Ground Start) FXS+ FXS+ 2W Input RX A RX B TX A TX B 2W Output (Outgoing call from FXS+) No Ring Gnd or Loop Open 1 1 0 1 Idle Ring Gnd 1 1 0 0 No Tip Gnd Ring Gnd or Loop Closed 0 1 1 1 Tip Gnd Loop Open 0 0 0 1 Tip Gnd & No Ringing Loop Closed 0 0 1 1 Tip Gnd & Ringing ( Inco
ADTRAN 1200080L1, Appendix A. 2FXS+ Failure Messages 61200.080L1-1 FXS+ Dual Voice Option Module 27 Appendix A FXS+ Failure Messages FAILURE MESSAGES AT POWER-UP The following messages indicate a probable component failure on the FXS+ Module: E01 - EPROM CS EPROM checksum error E02 - RAM ERR Static RAM error E03 - RNG FQ HI Ring generator frequency too high E04 - RNG FQ LO Ring generator frequency too low E05 - NO RING No ringing from ring generator E06 - TEST FAIL Self test could not finish E07 - RINGING Ringing detected incorrectly E10 - SIGNALING Failure of signal bit transmission
Chapter 3. Operation 61200.080L1-1 FXS+ Dual Voice Option Module 21 • Ringback This option generates ringback tone towards the T-span when enabled and the FXS+ card is in one of the Tamden modes. This may be needed on some cases when the network does not provide ringback tone. Choices include: - Enabled - Disabled. Port Configuration Menu Items/Parameters Summary Table 3-A provides
ADTRAN 1200080L1, Chapter 3. Operation 22 FXS+ Dual Voice Option Module 61200.080L1-1 PORT UTIL (Port Utility) Port Utility, a submenu of the TSU 100/600 Main menu item Utilities (UTIL) displays the current software information for each port installed in the unit. This information is required when requesting assistance from ADTRAN Customer Service or when updates are needed. When Port Utility is displayed, place the cursor on it and press Enter to display the first available port. See Figure 3-6. 3)UTIL 1)ENTER PASSCODE 2)TIME/DATE 3)FACTORY RESTORE 4)REINIT UNIT 5)UNIT ID 6)SOFTWARE REV 7)POR
ADTRAN 1200080L1, Appendix B. Signaling States Vs. Mode of Operation 30 FXS+ Dual Voice Option Module 61200.080L1-1 Ground start signaling provides its own tip ground in response to ring ground in the Tandem Mode. See Table B-B. Table B-B Tandem Mode The A and B signal bit states on the DS-1 signal are as follows: 0 = logic 0 is the DS-1 stream 1 = logic 1 is the DS-1 stream X = value is not significant Loop Open = phone on-hook Loop Closed = phone off-hook FXS+ 2W Input (Outgoing call from FXS+) Loop Open Loop Cl
ADTRAN 1200080L1, Chapter 3. Operation 61200.080L1-1 FXS+ Dual Voice Option Module 17 PORT CONFIG (Port Configuration) Port Configuration, a submenu of TSU 100/600 main menu item Configuration, is used to configure the FXS+ option module. The following submenu items are used to configure the parameters: • MODE • RX LVL (TLP) • TX LVL (TLP) • FAULT RESP • TANDM OPTIONS - Supervision - Dial Tone - Loop Rev Bat - Ring Back When Port Configuration is displayed, place the cursor on it and press Enter to activate. Scroll to display the port to be configured and activate with Enter. See Figure 3-5. The unit displays the first of five submenu ite
ADTRAN 1200080L1, Chapter 3. Operation 61200.080L1-1 FXS+ Dual Voice Option Module 25 TSU FEATURES USED WITH FXS+ OPTIONS In addition to the FXS+ menu items, two additional menu items of the TSU 100/600 may be operated in conjunction with the FXS+ option module. These are Factory Restore and Run Self Test. Factory Restore Factory Restore, a submenu of the TSU 100/600 Main menu item Utilities (UTIL), restores the factory installed default setting for all FXS+ option module parameters. When Factory Restore is displayed, place the cursor on it and press Enter. The unit is restored to preset factory defaults and returns
ADTRAN 1200080L1, Chapter 3. Operation 24 FXS+ Dual Voice Option Module 61200.080L1-1 VIEW SIG BITS (View Signaling Bits) View Sig Bits is used to view the status of the RX and TX signaling bits in the DS-1 stream. See Figure 3-8. The status of both the A and B bits is displayed. Figure 3-8 View Signaling Bits Display SET TX SIGNAL (Set Transmit Signal) Set TX Signal allows the A and B signal bits in the TX direction to be forced to a desired state for test. SET 2-W OUTPUT (Set 2-Wire Output) Set 2W Output allows the 2-wire voice interface output to be forced to a desired state for
ADTRAN 1200080L1, Appendix B. Signaling States Vs. Mode of Operation 61200.080L1-1 FXS+ Dual Voice Option Module 29 Appendix B Signaling States SIGNALING STATES VS. MODE OF OPERATION The four tables in this appendix describe the signaling states for voice card and the DS-1 PCM stream. Ground start signaling is not used in PLAR mode. See Table B-A. Table B-A PLAR Mode FXS+ FXS+ 2W Input RX A RX B TX A TX B 2W Output Loop Open X X 1 1 - Loop Closed X X 0 0 - Loop Open 1 1 1 1 No Ringing Loop Open 0 X 1 1 Ringing Loop Closed 0 X 0 0 No Ringing The A and B signal bit states on the D
ADTRAN 1200080L1, Chapter 2. Installation 12 FXS+ Dual Voice Option Module 61200.080L1-1 WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure. Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN. For Service, RMA requests, or mor
ADTRAN 1200080L1, Chapter 1. Introduction 2 FXS+ Dual Voice Option Module 61200.080L1-1 Functional Description The FXS+ is designed to fit in the option slot of the TSU 100/600 and is subject to its operation and control. The FXS+ is configured from the front panel of the TSU 100/ 600 or by an external personal computer (PC) program. The internal menus for its configuration are a part of the FXS+ module and are automatically installed when the FXS+ is plugged into the unit. Features The FXS+ Dual Voice option module has the following features: • Each 2
Table of Contents 61200.080L1-1 FXS+ Dual Voice Option Module iii Table of Contents Chapter 1. Introduction...................................................................................... 1 FXS+ Dual Voice Overview .................................................................................... 1 Functional Description.............................................
ADTRAN 1200080L1, Chapter 2. Installation 61200.080L1-1 FXS+ Dual Voice Option Module 11 POWER UP TESTING AND INITIALIZATION The FXS+ option module executes an abbreviated self test during the power up sequence, as described in the TSU 100/600 manual. No initialization input is required. Any previously configured setting for the FXS+ is restored automatically upon power up. Successful Self Test The green OK LED, located with the Module LEDs on the front panel, illuminates when a successful self test is completed and the configuration is successfully restor
ADTRAN 1200080L1, Chapter 1. Introduction 61200.080L1-1 FXS+ Dual Voice Option Module 5 Physical Description The FXS+ is an option module which plugs into the option slot in the rear of the TSU 100; see Figure 1-1. PORT X.3 DUAL FXS PORT X.1 PORT X.2 Figure 1-1 FXS+ Dual Voice Option Module The FXS+ rear panel includes a plastic plug over a cutout for additional connectors. This allows a plug-on board to be added to the FXS+ module. The PORT X.3 indication is linked to the port numbering philosophy of the TSU 100 product family. The X represents the slot number, and the .3 indicat
ADTRAN 1200080L1, Chapter 2. Installation 10 FXS+ Dual Voice Option Module 61200.080L1-1 Wiring The FXS+ Dual Voice option module offers two connec- tors for an analog voice interface. The connector is universal and accepts either an RJ-45 (8 Pin) or an RJ-11 (6 pin modular plug). The pinout is given in Table 2-A. The required wiring connection is: Connector Type (USOC) = RJ-45 Part number = AMP # 555164-1 Table 2-A 2-Wire Voice Pinout Connection PIN NAME DESCRIPTION 5 TIP TIP lead of 2-wire interface 4 RING Ring lead of 2-wire interface 1, 2, 3, 6, 7, 8 UNUSED - Pins used to mate with the FXS+ connector are as follows: RJ-11
EverFocus EDR410M Voice Recorder Specifications
EDR410M |
Sony ICD-BM1AVTP - Memory Stick Media Digital Voice Recorder Voice Recorder Specifications
ICD-BM1AVTP - Memory Stick Media Digital Voice Recorder |
Sony FS-85USB Voice Recorder Brochure
FS-85USB |
Sony ICD-R100PC - Icd Recorder Voice Recorder Specifications
ICD-R100PC - Icd Recorder |
Jung RAN 514 Voice Recorder Operating instructions manual
RAN 514 |
Panasonic RR US430 - Digital Voice Recorder Voice Recorder Operating instructions manual
RR US430 - Digital Voice Recorder |
Sony DCR-IP45 - Micromv Digital Camcorder Voice Recorder Operating instructions manual
DCR-IP45 - Micromv Digital Camcorder |
Olympus DW 90 Voice Recorder Instructions
DW 90 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Beko | HII64500FT | Operation & user’s manual | beko/hii64500ft-R9F.pdf | 13 Sep 2022 | 28 | |
2 | Philips | SPA1300/05 | Instructions for use | philips/spa1300-05-576.pdf | 13 Feb 2023 | 2 | 2.48 Mb |
3 | AEG | HG694340XB | Operation & user’s manual | aeg/hg694340xb-J89.pdf | 04 Dec 2022 | 20 | 1.46 Mb |
4 | Doro | Primo 305 | Operation & user’s manual | doro/primo-305-746.pdf | 25 Jan 2024 | 87 | |
5 | Elenco Electronics | EDU-37432 | Operation & user’s manual | elenco-electronics/edu-37432-2C4.pdf | 09 Feb 2023 | 4 | 0.72 Mb |
6 | Linx | MS Compact | Operation & user’s manual | linx/ms-compact-Y87.pdf | 30 Oct 2022 | 11 |
Uqique
Please read the instructions carefully before using the productProduct DescriptionThank you for choosing Uqique™ mini digital voice recorder, arguably the smallest digital voice recorder in the market that uses ADPCM algorithm to transmits crystal-clear and high-definition audio. Not just a voice recording device, it is also a MP3 media player and a USB …
UQ-VR896(1 pages) |
Edirol
Owner’s Manual1MP05012534As of Oct. 1, 2007 (EDIROL-1)Information When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below.EUROPE EDIROL (Europe) Ltd. Studio 3.4 114 Power Road London W4 5PYU. K.TEL: +44 (0)20 8747 5949FAX:+44 (0)20 8747 5948http://www.edirol …
R-09HR(124 pages) |
Sony
4-267-069-81(1)ICD-PX312IC RecorderOperating InstructionsGetting StartedBasic OperationsOther Recording OperationsOther Playback OperationsEditing FilesAbout the Menu FunctionUtilizing Your ComputerAdditional InformationTroubleshootingIndex
…
ICD-PX312(133 pages) |
Sony
NW-E50/E70E ModelChinese ModelSERVICE MANUALPORTABLE IC AUDIO PLAYERSPECIFICATIONSVer 1.3 2004.09Sony CorporationPersonal Audio CompanyPublished by Sony Engineering Corporation9-877-731-042004I16-1 2004.09ATRAC3plus*4 hr. 20 min. (64 kbps)5 hr. 50 min. (48 kbps)ATRAC3*2 hr. 00 min. (132 kbps)2 hr. 30 min. (105 kbps)4 hr. 10 min. (66 kbps)MP31 hr. 00 min. …
NW-E50(24 pages) |
Technogeek
Technogeek 611 Digital Voice Recorder cum Mp3 PlayerReg. Office : 205, 1B, Varun Arcade, Nr. Lawkim Industries, Ghodbunder Road, Thane, Maharashtra - 400610. Customer Care : 70455 21889 / 70455 31889 Email. : [email protected] Product Manual Product Features :* Voice Recording* Play Music : Multiple Music Format.* FM Radio* E-Book Reading : TXT Format* …
611(4 pages) |
Zoom
© 2019 ZOOM CORPORATIONCopying or reprinting this manual in part or in whole without permission is prohibited.Product names, registered trademarks and company names in this document are the property of their respective companies.All trademarks and registered trademarks in this document are for identication purposes only and are not intended to infringe o …
F8(6 pages) |
Crown Processor PIP-BEQPIP-BEQ (Processor ePDF User Guide, #KJZM96) PIP-BEQ, 16 |
Braun Electric Shaver CT6ccBraun Electric Shaver CT6cc Manual CT6cc, 35 |
Telex Intercom System XO-1Telex Intercom System User instructions (File: telex-xo-1-intercom-system-2, 24th Nov 2023) XO-1, 2 |
TP-Link Wireless Router TL-WN321GTL-WN321G Operation & user’s manual - 3AI994 TL-WN321G, 39 |
Samsung Digital Camera Galaxy Camera#A46WLY: Galaxy Camera Digital Camera Setup manual Galaxy Camera, 12 |
Olympus Digital Camera VS026401Digital Camera PDF Quick start manual VS026401, 2 |
CHC Handhelds HCE320HCE320 (Handhelds ePDF Manual, #KW3FTB) HCE320, 15 |
ProForm Other 545 SProForm Product User Manual: 545 S PDF Manual - E22DA9 545 S, 19 |
Nissan Automobile VERSA SEDANNissan Automobile VERSA SEDAN Manual VERSA SEDAN, 10 |
GE Refrigerator PSE26KSESSGE PSE26KSESS Manual (Energy manual), @729898 PSE26KSESS, 1 |
Midland Two-Way Radio ML3215ML3215 Operating instructions manual - 88AQOW ML3215, 12 |
3M Monitor Dynapro 350 Monitor, ET 3170 Terminal and ET 3200 Series Computers#9FHTG9 Dynapro 350 Monitor, ET 3170 Terminal and ET 3200 Series Computers: 3M Monitor Owner Documentation Dynapro 350 Monitor, ET 3170 Terminal and ET 3200 Series Computers, 4 |