Manualios.com

Develop D 16G Service Manual

Develop D 16G Manual Online:

4.2, 1195 votes
Develop D 16G User Manual
Develop D 16G User Guide
Develop D 16G Online Manual

Text of Develop D 16G User Guide:

  • D-16 (2) Removal of the PH Unit NOTES • NEVER attempt to replace the PH Unit with power being supplied to the printer. Doing that could lead to exposure to the laser beam, resulting in blindness • NEVER attempt to disassemble or adjust the PH Unit. Doing that could lead to exposure to the laser beam, resulting in blindness. 1. Remove the IR Unit. ☞ D-15 2.

  • Develop D 16G, S-13 PRE-ROTATION To select if the pre-rotation opera- tion for the Fusing Roller is per- formed when the Start key is pressed. • The default setting is “OFF”. ON OFF • If “OFF” is selected, the length of time until the first copy can be printed is shorter. FUSER TEMP.Ad To specify the fusing temperature when using plain paper (more than 186 mm). ✽ When a fusing failure has occurred • The default setting is “0”. 0(Standard) 1(Higher) Function Purpose Setting Details/Precautions

  • Develop D 16G, D-2 2. REPLACEMENT/CLEANING OF PARTS (1) Cleaning of the Paper Take-Up Roll 1. Raise the main unit to separate it from the Paper Feed Cassette. (2) Replacement of the Paper Take-Up Roll 1. Raise the main unit to separate it from the Paper Feed Cassette. 2. Using a soft cloth, wipe clean the surface of the Paper Take-Up Roller. 4136E002AA 2. Remove the Paper Take-Up Roller at the two points indicated. 4136E004AC

  • Develop D 16G, S-20 COPY ADF GLASS AREA To check for dirt in the scanning section of the Automatic Document Feeder. ✽ If spots appear in the copies <Procedure> 1. Load A4 L or Letter L paper into Tray1. 2. Press the Start key to start the “COPY ADF GLASS AREA” function. 3. Two copy samples are fed out. 4. Check that no spots appear in the copy samples. 5. Press the Stop key to stop the “COPY ADF GLASS AREA” function. CCD MOVE TO HOME To move the scanner to its home position in order to secure the scanner. ✽ When tra

  • Develop D 16G, D-1 1. MAINTENANCE SCHEDULE • To ensure that the printer produces good printed pages and to extend its service life, it is recommended that the maintenance jobs described in this schedule be carried out as instructed. NOTES • K = 1,000 printed pages • The contents of the Maintenance List are subject to change without notice. • For the part numbers, see Parts Manual and Parts Modification Notice. PM Parts Clean Replace Ref. Page in This Manual Continuous Making one printed page per job Paper Take-Up Roll When a paper take-up fai

  • Develop D 16G, D-34 NOTE If the Stop key is pressed, instead of the Yes key, the main screen is displayed and the set- ting returns to that before it was changed. Place the test pattern on the Original Glass again, make another test copy, and check it.

  • Develop D 16G, T- 8 3. TIMING CHART Original loaded Start key pressed Begin scanning of first page Begin scanning of second page Finish scanning of first page Finish scanning of second page Feeding two A4 L pages H L OFF ON Stop L H OFF ON Original Detection Sensor PC1 Paper Take-Up Clutch CL1 ADF Main Motor M5 Leading Edge Detection Sensor PC3 Original scanning Forward rotation

  • Develop D 16G, D-3 Finland, Sweden Norway VARO! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen. LOUKAN 1 LASERLAITE KLASS 1 LASER APPARAT VAROITUS! Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Puolijohdelaser Laserdiodin suurin teho 15 mW Aallonpituus 770-800 nm VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, so

  • Develop D 16G, D-19 (4) Removal of the Scanner Assy. 1. Remove the Original Cover. 2. Remove the Upper Cover Assy. (Original Glass). ☞ D-18 5. Remove the two screws, and then remove the Scanner Motor Mounting Bracket. 6. Remove the two screws, and then remove the Scanner Motor. 3. Remove the two screws, and then remove the Flat Cable Holding Plate. 4. Unplug the flat cable.

  • Develop D 16G, G-1 1. SPECIFICATIONS Name Installation method Original type Detectable Original sizes Paper capacity Registration Original loading orientation Productivity Original feeding Mode Power source Power consumption Dimension Weight Operating environment : : : : : : : : : : : : : : Automatic Document Feeder Inserted at upper-rear side of main unit Plain paper: 35 to 128 g/m 2 (9 to 34 lb.) A5 L, B5 L, A4 L, Legal L, Letter L, Invoice L Custom size width: 138 to 216 mm; length: 130 to 356 mm Maximum 50 sheets (80 g/m 2 ) (21 lb.) Center Face up 12 sheets/minute (with plain A4 L or Letter L paper) Standard mode DC 24 V, DC 5 V (supplied by main unit) Less than 30 W

  • Develop D 16G, T- 2 2 (13) C14A3: IR lamp malfunction <Detection Timing> <Troubleshooting Procedures> Description • The luminosity level of the Exposure Lamp is not stabilized within the predetermined period of time. Relevant Electric Parts IR Unit Controller/Mechanical Control Board (PWB-P) Step Action Ref. Page WIRING DIAGRAM Control Signal Location (Electric Parts) 1 Check the connection of the connectors, and then correct them if necessary. –– – 3 Replace PWB-P. –– – 4 Replace the Scanner Assy. –– –

  • M-4 3. PAPER PATH • The system employs a two-way paper supply system, in which paper is fed from either Tray 1 or the Multiple Bypass Tray. • When the optional Paper Feed Cassette is mounted, the system offers a three-way paper supply system. • The paper taken up and fed in by the Paper Take-Up Roll is transported through the printer by the Image Transfer Roller

  • Develop D 16G, T- 1 5 (2) C0210: H.V. abnormal <Detection Timing> <Troubleshooting Procedures> Description • The Drum Charge Monitor Voltage (HVC_MON) signal falls outside a predetermined range at any time after the lapse of a predetermined period of time after the Power Switch has been turned ON. • The Image Transfer Voltage Monitor signal (T_MON_V) and Image Transfer Current Monitor signal (T_MON_I) fall outside a corresponding predetermined range. Relevant Electric Parts Fusing Unit Controller/Mechanical Control Board (PWB-P) Step Action Ref. P

  • Develop D 16G, E-5 3. REPLACEMENT OF UNITS (1) Replacement of the Toner Cartridge <Removal Procedures> <Installation Procedures> 1. Lift up the Exit Tray and remove it. 2. Open the Front Door. 3. Remove the Imaging Cartridge. 4. Pull the lever of the Toner Cartridge in the direc- tion shown in the illustration and disconnect the Toner Cartridge from the Drum Cartridge. NOTE • If the Drum Cartridge is to be placed on a floor or similar place, use care to prevent toner from scat- tering around. 1. Take out a new Toner Cartridge and shake it in the horizontal direction sufficiently so that toner is agitated. NOTE • Placing the Toner Cartridge in an uprigh

  • M-3 8. Paper Feed • Paper is fed from Tray 1. 9. Bypass Paper Feed • Paper is fed from the Multiple Bypass Tray. 10. Image Transfer • A DC positive charge is applied to the Image Transfer Roller to transfer the visible image on the surface of the PC Drum onto the paper. 11. Paper Separation • The Charge Neutralizing Plate neutralizes any charge left on the pap

  • Develop D 16G, T- 3 3 (8) Printer system: Blank or black prints <Typical Faulty Images> <Troubleshooting Procedures> Step Check Result Action 1 Is a printed page blank? YES Check PH Unit connectors for proper connection. 2 Is the coupling of the drive mechanism of the Imaging Cartridge properly connected? NO Check coupling of drive mechanism for connection and correct as necessary, or replace Imaging Cartridge (Drum Cartridge, Toner Car- tridge). 3 Is the drum charge voltage contact point or PC Drum ground contact point

  • Develop D 16G, M-12 6-4. Detection of Toner Cartridge (1) Installation detection • The Imaging Cartridge, when loaded in position, is detected as follows. At the comple- tion of a warm-up cycle, the IC chip built into the Toner Cartridge (TC detection board) detects electrically whether or not the cartridge is loaded in position. (2) Interchangeability detection • The built-in IC chip (TC detection board) detects the applicable marketing area of the Toner Cartridge when power is turned ON or when the Front Door is opened and closed. (3) Toner Near Empty and Toner Empty Detection • The Toner Empty Detection Sensor detects the amount of tone

  • Develop D 16G, T- 3 6 (12) Printer system: Foggy background <Typical Faulty Image> <Troubleshooting Procedures> Step Check Result Action 1 Is PC Drum scratchy? YES Replace Drum Cartridge. 2 Is developing bias contact terminal in good contact with the mating part? NO Clean contact terminal or check terminal position. 3 Is PH window dirty? YES Clean. 4 Is the problem eliminated after checks have been made up to step 3? NO Replace High Voltage Unit (HV1). Replace Controller/Mechani- cal Control Board (PWB-P). 4011T004AA

  • T- 6 2. PAPER MISFEED 2-1. Initial Check Items • When a paper misfeed occurs in the printer, first make the following initial checks. Precautions for Clearing Misfeed • Reset the misfeed condition by opening and closing the Front Door after the misfeed has been cleared. Check Action Does the paper meet product specifications? Replace paper. Is the paper curled, wavy,

  • Develop D 16G, T- 3 (4) Motors Step Check Result Action 1 Is the LOCK signal of the Controller/Mechanical Con- trol Board HIGH when the printer is in the standby state? NO Replace the Con- troller/Mechanical Control Board. Replace the motor. 2 Does the REM signal of the Controller/Mechanical Control Board go from HIGH to LOW when the motor is energized? YES Replace the motor. NO Replace the Con- troller/Mechanical Control Board. Step Check Result Action 1 Does the input signal to the Controller/Mechanical Control Board go from HIGH t

  • T- 2 9 (4) Image reading system: Black streaks or bands <Sample of Image Quality Problem> <Troubleshooting Procedures> Step Check Result Action 1 Is the document damaged or dirty? YES Replace the document. 2 Is the Original Pad dirty? YES Clean it. 3 Does the Original Cover not lie flat? YES If the Original Cover is deformed or the hinges are damaged, re

  • Develop D 16G, T- 1 7 (4) C0510: Fuser temperature low <Detection Timing> <Troubleshooting Procedures> Description • The temperature detected by the Thermistor remains lower than the set temperature continuously for a predetermined period of time while the fusing temperature control is being provided. (The set temperatures are as follows: 140 °C during a print mode at 600 dpi; 70 °C during the standby mode.) Relevant Electric Parts Fusing Unit Thermistor (TH1) Fusing Roller Heater Lamp (H1) Controller/Mechanical Control Board (PWB-P) Thermostat (TS1) Power Unit (PU1) Step Action Ref. Page WIRING DIAGRAM Control Signal Location (Electric Parts) 1 Replace

  • Develop D 16G, D-13 9. Remove the three screws, unhook the tab, and then remove the Left Rear Frame. 10. Remove the three screws from the Left Rear Frame. 11. Remove the four screws, and then remove the Metal Bracket. 12. Remove the two screws, unhook the tab, and then remove the Left Rear Frame. 13. Remove the Upper Left Cover. 14. Remove the two screws, and then remove the Upper Right Cover and Protective Metal Bracket. NOTE • The Protective Metal Bracket is tightened together with the Upper Right Cover.

  • D-5 3-3. Disassembly (1) Removal of the Paper Feed Cassette Paper Take-Up Unit 1. Raise the main unit to separate it from the Paper Feed Cassette. (2) Removal of the Paper Size Detecting Switch 1. Remove the Paper Feed Cassette Paper Take-Up Unit. 2. Unhook the two tabs, and then remove the cover. 4516D003AB 3. Remove the actuator. 4136D035AA 4. Remove the six screws, unplug the two connec- to

  • Develop D 16G, S-23 5. SECURITY MODE • This mode is used to set various security functions. 5-1. Security Mode Function Tree 5-2. Security Mode Setting Procedure NOTE • Be sure to keep the access procedure for the Security mode from any unauthorized per- sons not involved with service operations. <Procedure> 1. Display the Service mode screen. ☞ S-11 2. Press the Stop key, then the 9 key. 3. The Security mode screen appears. <Exiting Procedure> • Press the Panel Reset key. (1) Security Function Purpose Setting Details/Pr

  • Develop D 16G, M-7 (2) When the pre-start control is provided 5-2. Print End Sequence Start key ON Polygon Motor Main Motor Paper Take-Up Solenoid /S1 Drum Charge Output Exposure Output Developing Output Image Tra ns fer Output Drum charge DC Drum charge DC Charge Reverse bias Unexposed area output ON Negative output 4980M017AB 4980M014AA Image Transfer Output Developing Output Polygon Motor Main Motor Drum Charge Output Laser Output Unexposed area illumination PS3 ON ON ON DC Substantially entire surface exposure AC ON Unexposed area illu- mination Reverse bias Charge Positive Negative N

Related Products and Documents (All in One Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 American Standard Copeland 7005.201 Installation instructions manual american-standard/copeland-7005-201-2FA.pdf 30 Jun 2022 8 0.96 Mb
2 Christie 38-VIV302-01 Operation & user’s manual christie/38-viv302-01-725.pdf 06 Sep 2023 52 1.39 Mb
3 Panasonic CF-VCF351W Operating instructions panasonic/cf-vcf351w-V74.pdf 25 Mar 2024 4 0.3 Mb
4 AMF MODEL S-4000 LT Parts and service manual amf/model-s-4000-lt-JN5.pdf 12 Mar 2024 82 5.56 Mb
5 Kenwood SJ330 series Operation & user’s manual kenwood/sj330-series-319.pdf 22 Feb 2023 2
6 ATEN KH1508A Specification aten/kh1508a-U71.pdf 14 Oct 2022 4 0.81 Mb

Similar Resources:

  • Lexmark

    X644E

    (191 pages)
    www.lexmark.comUser’s GuideMay 2006Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,registered in the United States and/or other countries.© 2006 Lexmark International, Inc.All rights reserved.740 West New Circle RoadLexington, Kentucky 40550X642e Laser MFP …
  • Panasonic

    DP-MC210

    (24 pages)
    This Quick Reference Guide provides safety instructions and a basic description of the unit’s functions. An illustrated leaflet provides instructions for easy installation. Please read before using the unit and save for future reference.The supplied Setup CD-ROM provides the Operating Instructions in PDF format with a detailed description on how to use the …
  • HP

    PHOTOSMART 5600

    (63 pages)
    CONFIDENTIAL Writer: Amy Laffitte - John Turner File Name: a-frnt Codename: RUGER Part Number: 229719-003 Last Saved On: 8/12/02 6:42 PM HP TFT5600 Rackmount Keyboard and Monitor (RKM) User Guide January 2004 (Fourth Edition) Part Number 229719-004 …
  • HP

    Officejet J5730

    (2 pages)
    HP Officejet J5730 All-in-One Printer, Fax,Scanner, CopierGet a low cost per page, fast results and the peace of mind of HP reliability backed up by athree-year warranty. Print and copy at up to 27 ppm black, 22 ppm colour. Enjoy theconvenience of a 35 page ADF, one-touch copying and more.The HP Officejet J5780 All-in-One series is designed for small busines …
  • Xerox

    Phaser 6125

    (6 pages)
    color laser printerPhaser® 6125QuickUseGuide6125 EN NL SV NO DA FI Rev ACopyright © 2008 Xerox Corporation. All rights reserved.Handleiding voor snel gebruikNLSnabbreferensguideSVHurtigbruksveiledningNOHurtig betjeningsvejledningDAPikaopasFI …
  • Samsung

    SL-M3870FW

    (410 pages)
    BÁSICOManual del usuarioBÁSICOManual del usuarioEsta guía contiene información relativa al proceso de instalación, funcionamiento básico y solución de problemas en Windows.AVANZADOEste manual contiene información relativa al proceso de instalación, configuración y funcionamiento avanzados, así como de solución de problemas, en diversos sistemas o …

Comments, Questions and Opinions: