Manualios.com

Diamond Products SC-7312 Instruction Manual

Diamond Products SC-7312 Manual Online:

3.2, 1833 votes
Diamond Products SC-7312 User Manual
Diamond Products SC-7312 User Guide
Diamond Products SC-7312 Online Manual

Text of Diamond Products SC-7312 User Guide:

  • Diamond Products SC-7312, 10 Maintenance - Before performing maintenance work switch off the SpeediCut (27) and pull off the plug cap. - Always check the SpeediCut before using it to make sure that it is in good working order. In particular, make sure that the cutting disc is properly mounted. Make sure that the cutting wheel is undamaged and suitable for the job it will be used for. - Operate the SpeediCut only at a low noise and emission level. For this ensure the carburetor is adjusted correctly. - Clean the SpeediCut regularly. - Check the fuel tank cap regularly for good sealing. Observe the accident prevention instructions issued by trade associations and insurance companies. NEVER make any modificat

  • Diamond Products SC-7312, 25 Instructions for periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! Users of the SpeediCut must not perform any maintenance work not described in this Instruction Manual. All such work must be carried out by a Diamond Products service center. General Entire SpeediCut Clean exterior, check for damage. In case of damage, have repaired by a qualified service

  • Diamond Products SC-7312, 3 2341 Delivery inventory 1. SpeediCut 2. Universal wrench 13/19 3. Offset screwdriver 4. Screwdriver for carburetor adjustment 5. Instruction manual (not shown) Symbols You will notice the following symbols on the saw and in the Instruction Manual: STOP Read instruction manual and follow the warning- and safety precautions! Particular care and caution! Forbidden! Wear protective helmet, eye and ear protection! Wear protective gloves! Wear respiratory protection! No smoking! No open fire! Direction of cutting wheel rotation Warning: the max. peripheral speed of the cutting disc is 2

  • Diamond Products SC-7312, 20 Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! The spark plug must be replaced in case of damage to the insulator, electrode erosion (burn) or if the electrodes are very dirty or oily. Turn the cover lock (6) to the “Unlocked ” position and carefully remove the filter cover (7). Pull the plug cap (8) off the spark plug. Use only the combinatio

  • Diamond Products SC-7312, 1 Instruction Manual Important: Read this instruction manual carefully before putting the SpeediCut into operation and strictly observe the safety regulations! Keep this instruction manual! Model SC-7312 Model SC-7314

  • Diamond Products SC-7312, 16 A Stopping the engine Push the combination switch (1) down to position . STO P 1 Working in winter In conditions of low temperatures and high humidity the carburetor can ice up. To prevent this, at temperatures below 32° F / 0° C hot air from the cylinder chamber can be inducted. This also brings the engine to operating temperature faster. At temperatures above freezing the carburetor must NOT be fed heated air. Failure to follow these instructions can lead to damage to the cylinder and piston! B Turn the cover lock (2) to the “unlocked ” position and carefully remove the filter cover (3). C 2 3 STOP Take the filter element (4) out of the

  • Diamond Products SC-7312, 13 11 12 14 13 E F NOTE: The two fastening nuts (11) must be loosened before tightening the V-belt or checking the tension. To increase the belt tension, turn the tightening screw (12) to the right (clockwise) with the combination wrench included with the SpeediCut. The belt tension is correctly adjusted when the nut (13) is centred on the mark (14). IMPORTANT: After tightening/inspection, make certain to tighten the fastening nuts (11). Tightening the V-belt / Checking V-belt tension IMPORTANT : Exact V-belt tension is essential for maximum cutting performance with minimum fuel consumption. Improper V-belt tension will result in premature wear to the V-belt and V-belt wheel or damage

  • Diamond Products SC-7312, 11 1 24 25 23 2 3 4 5 6 7 8 14 15 16 17 18 19 20 9 10 2122 12 1113 Displacement cu in (cm 3 ) 4.5 (73) 4.5 (73) Bore in (mm) 1.97 (50) 1.97 (50) Stroke in (mm) 1.46 (37) 1.46 (37) Max. power hp (kW) 5.6 (4.2) 5.6 (4.2) Max. torque Ft/lbs 6.75 6.75 Idling speed rpm 2.500 2.500 Clutch engagement speed rpm 3.800 3.800 Engine speed limitation rpm 9.350 9.350 Max. spindle speed rpm 4.300 4.300 Sound pressure level at the operators ear 1) dB (A) 104 104 Sound pressure level at the bystander’s position (50 ft) 1) dB (A) 86 86 Vibration acce

  • Diamond Products SC-7312, 24 15 16 13 14 Put the guard plate (13) on. Screw on nuts (14) and tighten by hand. To tighten the V-belt see ”Tightening the V-belt / Checking V-belt tension”. Tighten the nuts (14) firmly with the combination wrench. IMPORTANT: When you reposition the cutting attachment, the direction of rotation of the cutting wheel changes. Diamond cutting wheels must be installed in the proper direction of rotation! A Replacing/cleaning the spark arrester screen The spark arrester screen should be checked and cleaned regularly. Loosen the 2 screws (15) and remove the spark arrester screen (16). Reassembly the spark arrester screen and tighten the screws.

  • Diamond Products SC-7312, 23 3 4 5 6 7 Cutting attachment in central / side position NOTE: The SpeediCut is delivered with the cutting attachment mounted in the middle position (C). For cutting up against obstacles, such as curbs or walls, the cutting attachment can be mounted to one side (D). Use this position only when actually necessary, and afterwards return the cutting attachment to the middle position. In this position the SpeediCut has better balance, is easier to guide, and is not as fatiguing for the operator. 1 2 C Repositioning the cutting attachment Loosen n

  • Diamond Products SC-7312, 18 8 9 10 1 2 3 4 7 65 A MAINTENANCE CAUTION: Before doing any work on the SpeediCut turn off the engine, remove the cutting disc, pull the plug cap off the spark plug and wear protective gloves! CAUTION: Start the SpeediCut only after complete assembly and inspection. STOP B IMPORTANT: Because many of the parts and assemblies not mentioned in this Instruction Manual are vital to the safety of the unit, and because all parts are subject to a certain amount of wear and tear, it is important for your own safety that you have the unit checked and maintained regularly by a Diamond Products service center. IMPO

  • Diamond Products SC-7312, 17 Adjusting the carburetor NOTE: The grinding parts are equipped with an electronic ignition to limit the speed. The carburetor also has a fixed jet which cannot be adjusted. At the factory the idling speed has been set to approx. 2,500 rpm, but the running-in process of a new engine may require slight readjustment of the idling speed. E For correct adjustment of the idling speed the following steps must be carried out: Start the engine and run it until it is warm (about 3 - 5 minutes). F Readjust the idling speed. If the cut-off disc is still turning when the engine is running, unscrew the adjusting screw of the throttle valve (9) until the cut-off disc is no longer turning. When

  • Diamond Products SC-7312, 8 Cutting metals IMPORTANT! Always wear approved respiratory protection! Materials that can release toxic substances may be cut only after notifying the proper authorities and under their supervi- sion or that of a person appointed by them. CAUTION! The rapid rotation of the cutting disc heats metal and melts it at the point of contact. Swing the guard as far down as possible behind the cut (19) in order to direct the stream of sparks forward, away from the operator (fire hazard). - Determine the direction of cutting, mark the cut and apply the disc to the material at moderate speed, to cut a guide groove before going to top speed and applying

  • Diamond Products SC-7312, 19 11 12 E STOP NOTE: To install the cutting wheel see “Mounting the cutting wheel”. F Cleaning / changing the air filter Turn the cover lock (11) to the “Unlocked ” position and carefully remove the filter cover (12). There is an O-ring (G/15) between the filter cover (12) and the air filter hood (G/14). G Unscrew the screws (13) and remove the air filter hood (14). Clean the O-ring (15) with a brush and inspect for damage. 13 14 15 H Remove the foam prefilter (17) from the filter cover. Pull the paper cartridge (18) from the hood. Remove the inner filter (16) from the intake openin

  • Diamond Products SC-7312, 15 CAUTION: Observe the SAFETY INSTRUCTIONS on page 5! Start the SpeediCut only after complete assembly and inspection! Move at least 10 ft. away from the place where you fueled the SpeediCut. Make sure you have a good footing, and place the SpeediCut on the ground in such a way that the cutting disc is not touching anything. D 1 2 10 Feet Turn the hood lock (2) to position and hold it there. Pivot the hood (3) back as far as it will go. Release the hood lock and pivot the hood lightly back and forth until the lock

  • Diamond Products SC-7312, 26 Guarantee Diamond Products guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the 90 days after purchase. Please note that in some countries particular guarantee conditions may exist. If you have any questions, please contact your salesman, who is responsible for the guarantee of the product. Please note that we cannot accept any responsibility for damage caused by: • Disregard of the instruction manual. • Non-performance of the

  • 7 Kickback and lock-in - When working with the SpeediCut there is a danger of kickback and lock-in. - Kickback occurs when the top of the cutting disc is used for cutting (15). - This causes the SpeediCut to be thrown back toward the user with great force and out of control. Risk of injury! To prevent kickback, observe the following: - Never cut with the section of the cutting d

  • 5 - Always wear safety shoes or boots (G) with steel toes, non-skid soles, and leg protectors when working with the SpeediCut. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing. - Always wear a work suit (H) of sturdy material. Fuels / Refuelling - Go to a safe, level place before refuelling. Never refuel wh

  • Diamond Products SC-7312, 14 NOTE: For preparing the fuel-oil mixture first mix the entire oil quantity with half of the fuel required, then add the remaining fuel. Shake the finished mixture thoroughly before pouring it into the SpeediCut tank. Caution: Open the tank cap carefully, as pressure might have built up inside! It is not wise to add more engine oil than specified to ensure safe operation. This will only result in a higher production of combustion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the muffler. In addition, fue

  • Diamond Products SC-7312, 6 Cutoff discs - The protection hood must always be on! Change discs only with the engine off! - There are two basic types of cutoff discs: - For metal (hot cutting) - For masonry (cold cutting) NOTE: When using diamond cutoff discs, always make sure to observe the “direction of rotation” markings. Diamond discs should only be used for cutting masonry/brick/ concrete etc. - Cutoff discs are intended only for radial loading, i.e. for cutting. Do not grind with the sides of the cutting disk! This will break the disk(10)! Caution! Never change direction (turning radius less than 15 feet), exert lateral (sideways) pressure, or tip the SpeediCut during cutting (11)! - Use a cuttin

  • Diamond Products SC-7312, 4 2 3 D B A 1 4 E C F SAFETY PRECAUTIONS General precautions - The operator MUST read this instruction manual to ensure safe operation (even if you already have experience in using cutoff saws). It is important to be familiar with the operation of this particular cutoff saw. Users insufficiently informed will endanger themselves as well as others due to improper handling. - Let only persons who have experience in using cutoff saws work with this unit. When letting another person use the SpeediCut

  • Diamond Products SC-7312, 12 Place the spring washer (8) on the arbor and insert the screw (C/9) and tighten by hand. Slowly turn the cutting disc until the stop hole of the V-belt wheel is visible in the drive-arm hole (10). Insert the Allen key (2) as far as it will go. The shaft is now blocked. Tighten the screw with the combination wrench (1) NOTE: Tighten the screw firmly, as otherwise the cutting wheel may slip during cutting. A D 8 1 2 10 PUTTING INTO OPERATION CAUTION: Always turn off the engine and pull off the spark plug cap before doing any work on the SpeediCut! Always wear protective gloves! CAUTION: Start the SpeediCut only after complete assembly and

  • Diamond Products SC-7312, 22 134 2 A 22 Replacing the return spring Remove the fan housing (see above under “Replacing the starter cable”). Take off snap ring (1). Remove the cable pulley (2). Unscrew screw (3) and carefully remove spring housing (4). Remove screws (3) and carefully remove the return spring with housing (4). CAUTION: Danger of injury! If the spring is broken it may pop out! NOTE: The old spring should be recycled. Replacement return springs are delivered already tensioned in the housing. Before installing, lightly grease the new spring with multi-purpose gre

  • 9 In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water. Diamond Products offers the right accessories for all wet cutting applications. - Remove foreign objects such as sand, stones and nails found within the working area. Caution: Watch out for electric wires and cables! The rapid rotation of the cutting disc at the point of

Related Products and Documents (Saw):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Epson T087220 Material safety data sheet epson/t087220-3QA.pdf 24 Apr 2023 4 0.03 Mb
2 Harman Pellet Pro 2 Manual  harman/pellet-pro-2-498.pdf 29 Mar 2023 18 2.24 Mb
3 Frigidaire FAA065P7A2 Installation instructions frigidaire/faa065p7a2-PSR.pdf 20 Dec 2022 3 1.45 Mb
4 Sanyo VPC HD1 - Xacti Camcorder - 720p Instruction manual sanyo/vpc-hd1-xacti-camcorder-720p-QA7.pdf 17 Jul 2023 31 0.16 Mb
5 Portland 61714 Owner's manual and safety instructions portland/61714-6ZR.pdf 11 Nov 2023 12
6 Nespresso Essenza Operation & user’s manual nespresso/essenza-ER5.pdf 22 Jan 2023 46

Similar Resources:

  • Porter-Cable

    1500

    (14 pages)
    1Tile SawInstructionmanualThe Model and Serial No. plate is located on the mainhousing of the tool. Record these numbers in thespaces below and retain for future reference.Model No. ______________________________________Type ___________________________________________Serial No. _______________________________________IMPORTANTPlease make certain that the pers …
  • Brutus

    Power Pro 1100

    (12 pages)
    Read and follow all safetyand operating instructionsbefore using this saw.Power Pro 1100 Tile SawOWNER’S MANUALBT65011 &BT65011INDWARNING!*CE relates to230v-240v only’ …
  • Ryobi

    P500

    (22 pages)
    OPERATOR’S MANUAL5-1/2 in., 18 VOLTLASER CIRCULAR SAW P500SAVE THIS MANUAL FOR FUTURE REFERENCEYour laser circular saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.WARNING: To reduce the risk of injury, …
  • Bosch

    GTS 10 XC Professional

    (421 pages)
    Robert Bosch GmbHPower Tools Division70764 Leinfelden-EchterdingenGERMANYwww.bosch-pt.com1 609 92A 15S (2015.01) PS / 422 EUROGTS 10 XC Professionalde Originalbetriebsanleitungen Original instructionsfr Notice originalees Manual originalpt Manual originalit Istruzioni originalinl Oorspronkelijke gebruiksaanwijzingda Original brugsanvisningsv Bruksanvisning i …
  • REX

    MANTIS 125

    (23 pages)
    REX Band SawXB125・120A・Operation ManualBe sure to read this manualbefore using the machine. Be sure to give this Operation Manualto the user. To ensure safe and effective use, read this Operation Manual carefully before use. Keep this manual handy so the usercan refer to it when necessary.Date of Purchase: Year MonthSales Agent: 50/60HzXB125(ChainVice� …
  • Master-force

    240-0021

    (4 pages)
    Page 1 10” Compact-Slide Miter Saw 240 -0021 For more information or to ask questions, Call Toll-Free: (866) 902-9690 Monday-Friday between 8:30 AM and 5:00 PM ET CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference. Q …

Comments, Questions and Opinions: